Evolis Avansia Instruction Manual

Other manuals for Avansia

3

Table of contents

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide

IRA3D

IRA3D POETRY4 Original instructions

How to clean AVANSIA?

INTRODUCTION

This documentation explains how to clean Avansia:

•Routine printer cleaning

•Manual printer cleaning

Note: To optimize printing quality, Evolis recommends

these cleaning cycles frequencies:

Routine printer cleaning - Every 1000 printing cards

Manuel cleaning – Every 10000 cards

Editorial

Staff

Indice

Modification

type :

Author:

21-03-2016

A0

Creation

NF

TECHNICAL

NOTE

CONTENT

ROUTINE PRINTER CLEANING.......................................... 2

Cleaning roller replacement 6

MANUAL PRINTER CLEANING......................................... 9

Flip over rollers cleaning 10

Primary transfer rollers cleaning 15

Feeding roller cleaning 18

Transport rollers cleaning 20

Cleaning rollers cleaning 24

Filter Cleaning 27

Print head cleaning 29

2

ROUTINE PRINTER CLEANING

Recommended cleaning cycle: Every 1000 cards.

Servicing accessory: Evolis Avansia Adhesive cleaning card.

Before cleaning, remove cards from the printer.

Evolis Avansia cleaning cards can only be used once.

The frequency and quality of cleaning are determining factors to prolong the life of the print

head, printer, prevent printing, transport and feeding issue. Special care should be taken for this

operation.

Follow the procedure below:

Access to User mode:

When the power starts and the printer turns on in Normal Mode, and [Ready] appears on the LCD Panel.

1. Press once on Menu

2. “Printer info” is displayed: Press on

3. “Version” is displayed: Press on

4. “Cleaning” is displayed: Press on Set

3

5. “Cool down” is displayed; wait until the figure drops to 70 (around 10 mn if the printer is hot).

6. “Remove film” is displayed

Open the front cover (a) and remove the Transfer film (b) then close the front cover.

7. “Remove cards” is displayed

Open the black cover (a) open the feeder (b) and remove the cards (c).

b

a

a

b

c

4

8. “Cleaning Set Cleaning Crd” is displayed

Remove the film protection from the Evolis Avansia adhesive cleaning card and insert it as shown on the

picture.

9. “Cleaning Set: Start” is displayed: Press on Set

10. “Cleaning Cleaning “is displayed: The cleaning starts automatically.

11. “Cleaning Complete” is displayed: The cleaning is completed and the cleaning card is ejected.

5

12. Put back the transfer film in the retransfer module (a), close the front cover (b) and put back the card (c).

Close the feeder (a) and the top cover (b). Your printer is ready to use.

a

c

b

b

a

6

Cleaning roller replacement

An adhesive cleaning roller is delivered with the Transfer film, it has to be installed each time you

change the ribbon

1. Open the front cover.

2. Remove the cleaning tape cassette.

7

3. Lift up the tape spindle and remove the cleaning roller.

4. Put back the new cleaning roller.

5. Clip the cleaning roller

8

6. Put back cleaning tape cassette (blue part).

7. Close the front cover.

9

MANUAL PRINTER CLEANING

Recommended cleaning cycle: Every 10000 cards or after each technical hardware maintenance.

Servicing accessories: Evolis pre-saturated cleaning cards, cotton swabs, wipes, dry air pressure

spray.

Remove cards from the printer.

Cleaning cards can only be used once.

The frequency and quality of cleaning are determining factors to prolong the life of the print

head, printer, prevents printing and feeding issues. Special care should be taken for this

operation. Do not hesitate to use several pre-saturated cleaning cards if necessary.

Blow the different parts of the printer with a dry air pressure spray to remove dust before the

cleaning.

10

Flip over rollers cleaning

1. Turn off the printer.

2. Open the top cover (a) and remove card feeder (b).

3. Open the front cover (a) and the trapdoor cover (b).

b

a

b

a