ETC Source Four Mini LED User manual

Product information and specifications subject to change.

Part Number: 7063M1240 Rev A

Released: 2014-02

Low Voltage User Manual

Revision A

Table of Contents

ETC® and Source Four Mini™ are either registered trademarks or trademarks of Electronic

Theatre Controls, Inc. in the United States and other countries.

ETC permits the reproduction of materials in this manual only for non-commercial

purposes. All other rights are reserved by ETC.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Basic Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Install Lens Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Terminate 12V Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Adjusting the yoke position . . . . . . . . . . . . . . . . . . . . . . .4

Setting the angle with the yoke . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Focusing the beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Shaping the Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Pattern Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Color Frame Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using a C-clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Cleaning the Glass Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

1 Source Four Mini Low Voltage User Manual

Introduction

A selection of field installed lens tubes are available (sold separately), providing

19°, 26°, 36°, and 50° field-angles. The Source Four Mini Low Voltage can be field

outfitted for using either a canopy mounting kit or a miniature c-clamp, both sold

separately.

WARNING:

Please note the following safety warnings before use:

Do not mount the luminaire on or near combustible surfaces.

Do not operate the luminaire without a lens installed.

Always hang the luminaire with the color frame retaining clip in

the locked position.

The Source Four Mini Low Voltage luminaire ships

standard with a yoke, a three foot bare end power

cable, a dimmable 12V MR16 lamp and is intended

for low voltage installations only.

WARNING:

This luminaire is intended for

12 volt operation and power

input. DO NOT connect this

luminaire to a line voltage

system (120V or otherwise).

canopy kit and

lens tube sold

separately

miniature

c-clamp and lens

tube sold

separately

Basic Assembly

Color frame

retainer clip

Yoke

Pattern Holder

Slot

Shutter Barrel

Shutters x4

Lamp housing

knob

Safety attachment

point

Color frame

Lens tube

(sold separately)

Lamp housing

Beam focus

knob

INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO

PERSONS

IMPORTANT SAFETY INSTRUCTIONS

Lighted lamp is HOT!

WARNING - To reduce the risk of FIRE OR INJURY:

1) Turn off power and allow to cool before replacing lamp.

2) Lamp gets HOT quickly! Contact only switch/plug when turning on.

3) Do not touch hot lens, guard, or enclosure.

4) Keep lamp away from materials that may burn.

5) Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage

lamp.

6) Do not operate the luminaire with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

3 Source Four Mini Low Voltage User Manual

Install Lens Tube

A lens tube (sold separately) must be installed prior to use of the Source Four Mini

Low Voltage luminaire. There are four lens tube sizes available; 19°, 26°, 36°, and

50°

Step 1: Unscrew the beam focus knob from the loose lens tube.

Step 2: Slide the lens tube into the shutter barrel.

Step 3: Re-install the beam focus knob.

Terminate 12V Wiring

The Source Four Mini Low Voltage luminaire is provided with a bare end (2 wire)

power cable for termination to a standard low voltage (12 volt) system.

To install this luminaire using a canopy mount, reference the Source Four Mini Low

Voltage Canopy Mounting Kit Installation Guide provided with the canopy mounting

kit for wire preparation and canopy installation instructions.

WARNING:

DO NOT connect this luminaire to a line voltage system.

Mis-wiring your luminaire presents a possible risk of injury

to you and definite damage to the luminaire.

Beam focus knob

Adjustments

Adjusting the yoke position

The Source Four Mini Low Voltage luminaire provides multi-positioning capabilities

within its yoke for overall luminaire angle.

Setting the angle with the yoke

Step 1: Loosen the yoke locking knob. Do not remove the knob.

Step 2: Tilt the luminaire to the desired position.

Step 3: Tighten the yoke locking knob to secure position.

Focusing the beam

Step 1: Loosen the beam

focus knob located

under the barrel. Do

not remove the knob.

Step 2: Slide the lens tube

forward or backward to

achieve the desired

beam edge.

Step 3: Once the luminaire is

focused, tighten the

beam focus knob.

Yoke locking

knob

Beam focus knob

5 Source Four Mini Low Voltage User Manual

Shaping the Beam

The beam can be shaped using the four shutters or with a pattern.

The Source Four Mini has four shutters:

left, right, top, and bottom. Each shutter

can be pulled out or pushed in to create

the desired beam shape.

Color Frame Holder

Source Four Mini lens tubes ship with a 2 ¾” or 70mm color frame, which is a metal

frame used to hold color media (often referred to as gel) in front of the lens. The

color frame holder is equipped with a retaining clip that prevents the color frame

from falling out during use.

WARNING:

Make sure the color frame is locked in position with the retaining

clip.

1” Diameter

Pattern Projection

The Source Four Mini Low Voltage luminaire has a

pattern holder slot on the top side of the shutter

barrel, in front of the shutter. It accommodates a E-

size (37.5mm with a 25.4mm image area) pattern

holder.

Use an optional donut in the color frame holder to

enhance pattern projection.

When the slot is not in use, a small sheet metal cover

secured with a Phillips screw prevents light leakage.

Step 1: Use a Phillips screwdriver to loosen the

screw on the slot cover. Do not remove the

screw.

Step 2: Slide the cover completely forward to

expose the slot.

Step 3: Insert the pattern holder.

Step 4: Slide the slot cover back toward the

shutters until it meets the pattern handle.

Leave enough space to move the handle.

Step 5: Secure the slot cover by tightening the

screw.

Step 1: Release the retaining clip by gently

pushing it up.

Step 2: Insert the color frame.

Step 3: Lock the retaining clip by gently pushing it

down.

Additional accessories are available for the Mini that

also fit into the color frame holder including the top

hat, short top hat, half hat, short half hat, and donut.

When an accessory is used, the color frame should be installed in the rear slot of

the holder.

Using a C-clamp

A miniature c-clamp is available (sold separately) for use with the Source Four Mini

Low Voltage luminaire.

Step 3: Loosen the c-clamp yoke bolt and rotate the yoke to the desired position.

Step 4: Tighten the bolt to lock the luminaire.

Note:

Always insert the color frame open side down.

CAUTION:

Tighten the c-clamp pipe bolt to about 18in/lbs. (Approximately finger

tight plus up to one-quarter turn.) Do not use excessive force.

Note:

The Source Four Mini yoke has a c-clamp hole with a .406” diameter.

Retaining

clip

Color

Frame

Holder

Yoke bolt

Pipe bolt

c-clamp

The c-clamp attaches the luminaire yoke and allows

you to adjust the position of the luminaire once it is

mounted to a pipe (fits to a 3/8” to 1” pipe).

Step 1: Tightly fasten the c-clamp to the yoke with

the provided yoke bolt and lock washer.

Step 2: Place the c-clamp on the mounting pipe,

and then tighten the pipe bolt to secure it.

7 Source Four Mini Low Voltage User Manual

Replacing the Lamp

AVERTIR:

Risque d'incendie ou de blessures. Eviter toute matière

inflammable. Débrancher avant de changer la lampe. Ne pas

toucher la lampe.

WARNING:

Allow the lamp housing to cool before replacing the lamp.

CAUTION:

RISK OF FIRE - USE 50 WATT OR SMALLER, 12 VOLT, TYPE

MR16 SHIELDED LAMP.

PRUDENCE:

Pour éviter risque d'incendie utiliser seulement une lampe 12V

type MR16 50Watts maxi. avec écran.

CAUTION:

DRY LOCATIONS ONLY.

POUR EMPLACEMENTS SECS SEULEMENT.

Note:

It is recommended to use an MR16 lamp with a nominal beam

angle of 35 degrees.

Step 1: Disconnect power to the Source Four Mini before installing the lamp.

Step 2: Loosen the brass lamp housing knob on the back of the lamp housing. The

knob is not captured so it may come loose from the luminaire.

Step 3: Pull the lamp housing away from the

luminaire body.

Step 4: Pull on the lamp carefully to remove it from

the lamp housing.

Step 5: Gently push down on the replacement lamp

until it is seated in place.

Step 6: Re-align the housing into the grooves of the

luminaire.

Step 7: Align the knob with the hole, and tighten the

lamp housing knob.

Lamp housing

knob

Other manuals for Source Four Mini LED

Table of contents

Other ETC Dj Equipment manuals

ETC

ETC Source Four LED S4LEDLS User manual

ETC

ETC Source 4WRD User manual

ETC

ETC Desire series User manual

ETC

ETC Source Four PARN User manual

ETC

ETC Source 4WRD User manual

ETC

ETC Desire series Configuration guide

ETC

ETC Prodigy FlyPipe Studio User manual

ETC

ETC IRIDEON AR500 User manual

ETC

ETC Releve Spot Mounting instructions

ETC

ETC Source Four jr User manual

ETC

ETC ColorSource Spot V 1.0 User manual

ETC

ETC ColorSource Linear Pearl User manual

ETC

ETC fos/4 Series User manual

ETC

ETC Source Four jr User manual

ETC

ETC ColorSource Spot jr v2.0 User manual

ETC

ETC ColorSource Fresnel V User manual

ETC

ETC High End Systems SHOWGUN Manual

ETC

ETC F-Drive R12 Series User manual

ETC

ETC Source Four Zoom CE User manual

ETC

ETC Source Four Mini LED User manual

ETC

ETC Desire D40 User manual

ETC

ETC High End Systems SolaPix 19 User manual

ETC

ETC ColorSource Linear User manual

ETC

ETC Irideon WLZ User manual

Popular Dj Equipment manuals by other brands

ALPHA LITE

ALPHA LITE ALPHA 1500 User manual book

Chauvet

Chauvet OVATION E-930VW Quick reference guide

Zumtobel

Zumtobel APHRODITE Home Instructions for use

Snow Masters

Snow Masters Zig Oscillator user manual

EuroLite

EuroLite 50530554 user manual

Beamz

Beamz BUV243 user manual

thomann

thomann Stairville DJ Lase 40-G MK-III user manual

Eagletone

Eagletone 6 Eyes Flower user manual

EuroLite

EuroLite FLD-1508 user manual

Technical Pro

Technical Pro LG8xSEA user manual

JB Systems

JB Systems Lounge Laser DMX Operation manual

Lightmaxx

Lightmaxx Vega Halo 90 user manual

Elation

Elation FUZE WASH Z350 user manual

Maverick

Maverick MK3 WASH Quick reference guide

Infinity

Infinity TF-260C7 Fresnel manual

Chauvet

Chauvet EVE E-50Z Quick reference guide

Eliminator Lighting

Eliminator Lighting E 138 manual

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC user manual