Erone SEL2641R433-K8 User manual

Block Programmable

Receiver 800/1600 Users

SEL2641R433-K8/K8P/K16P

Installation

Manual

We appreciate your choice of this product.

This product is addressed to manage the access in

automatic door control systems

This appliance has been carefully manufactured and checked.

The manufacturer has designed this system to assure the best rielability and

satisfaction in the time

We recommend to read carefully this manual before to proceed to the installation

Pag. 2

Layout

Legend

1 : Backlighted LCD display

2 : LCD trimmer adijust

3 : Terminal boards

4 : Relay1

5 : Relay 2

6 : 4 pin strip connector

7 : RJ11 phone connector

8 : Buzzer

9 : D-type 9 pin male connector

10 : Plugs

11 : Screws

12 : Aerial net

13 : Receiver box

Fig. 1

K223B

Fig. 2

ER ONE

Pag. 3

Contents

ImportantRecommendations ........................................Pag.4

GeneralRemarks.................................................Pag.4

Receivercomposition..............................................Pag.4

Versions ..................................................Pag.4

Technicalspecifications ............................................Pag.4

Compatibility ..................................................Pag.5

Introduction ..................................................Pag.5

MASTERtransmitteruseguide............................Pag.5

USERtransmitteruseguide..............................Pag.5

KEYPADuseguide ....................................Pag.5

Installation ..................................................Pag.6

Electrical connections

Transmittersprogramming ..........................................Pag.7

MASTER transmitter memorization

USER transmitter memorization

Main menu structure

MenuDelete ..................................................Pag.9

Single user cancellation

All users cancellation

Complete initialization of the receiver

MenuModifyuser................................................Pag.10

Enable / Disable

Modify relay or key parameters

Copyanddatatransfermenu........................................Pag.11

Memory Visualization on the LCD

Print user list

Print events

Transmitter S/N configuration

Data transfer from and to a backup device

Receiverconfigurationmenu ........................................Pag.15

Change Password

Relay configuration ( Relay1 - Relay 2)

Facility Code set-up ( Facility Code 1 - Facility Code 2 )

Receiverauto-testsystem...........................................Pag.17

RS232Connections...............................................Pag.18

Accessories ................................................Pag.19

Pag. 4

Important recommendations

0Never interfere with the product when connected to a

power source;

0Avoid direct contact with water;

0Regularly check the state of the product;

0Respect the current norms;

0Wear protected glasses to avoid injury during the drilling

phase;

0Change the factory code;

General remarks

Radio

The materials and the technology used have made it possible to

create a system functioning on the 433,05 - 434,790 MHz

frequency band, used by LPD equipments and therefore subject

to european radio and electromagnetic compatibility regulations

(CE).

Rolling Code

In order to guarantee your safety and the total inviolability of the

communication between transmitter and receiver, the code sent

out by the transmitter changes every time the equipment is used

and is recognised by the receiver only, thanks to an unfalsifiable

code-setting calculation. The system thus conceived avoids all

risk of being recording or of the code being copied (268 million

combinations).

Composition of the receiver

See fig. 2

Item Description Q.ty

1 Receiver 1

2 Antenna wire 1

3 Assembly screws 4

4 Plugs 4

Technical specifications

!Receiver

Carrier frequency 433,92 MHz

Local oscillator freq. 6,6128 MHz

Power supply 12/24 Vac/dc

Modulation AM/ASK

Number of memorizable users 812 - 1631 (*)

Number of relays 2

Type of output contact 1 NO, 1 NO/NC

Commutable power 24 VA

Maximum relay voltage 60 V

Absorbtion 95 mA (relay excited)

Housing protection IP 40

Operating temperature from -10°C to +55°C

Overall dimensions 180x140x68mm

Weight 330gr

(*) According to the version

!Transmitter Types E2-E4-E2M

Operating Frequency 433,92 MHz

Power supply 12 Vdc

Modulation AM/ASK

Number of functions 2 or 4

Coding type Rolling Code

Number of combinations 2

E.r.p. 100 - 200 µW

Absorbtion 18 mA

Range in open space with

receiver with antenna 100-200 meters

Housing protection IP 44

Operating temperature -10°C to +55°C

Dimensions 82x48x16 mm

Weight 32gr

Battery type Alkaline - 23A

Receiver Transmitters

SEL2641R433-KX S2TR2641E2 - E4 - E2M

( Series 024A)

SETR2641AM2

( Series mini AM)

SEDK2641A4 (Digikey )

Compatibility

Look at the following table for the compatibility between the

receiver and the different series of Erone Transmitters

Versions

SEL2641R433-K8 RX 800 Users

SEL2641R433-K8P RX 800 Users PCCOM (*)

SEL2641R433-K16P RX 1600 Users PCCOM (*)

(*) PCCOM : Internal firmware with predisposition for the

connection to a PC with Software PCCOM

Pag. 5

Introduction

This receiver allows to manage 800 pre-coded transmitters

( 2 or 4 keys ) for a wireless access control system.

There are 2 output relays with NO and NC/NO contacts.

The managing of the users is fully wireless: the receiver can

be programmed by using a special transmitter called

“MASTER transmitter”.

This is memorized during the first installation.

The internal EEPROM allows to memorize up to 7 MASTER

transmitters.

All the operations are displayed throught a 16x2

backlighted LCD display.

The menu is friendly and very easy.

Master transmitter use guide

Each MASTER transmitter allows to set the receiver using

just 2 keys.

The transmitter keys can have different meanings

depending upon the phase, as shown in the following

examples:

Activation of the LEFT key

Answer NO to a question

Activation of the RIGHT key

Answer YES to a question

Simultaneous activation of the both keys

LEFT and RIGHT : Back to the previous menu

Activation of the LEFT key

Cyclical scroll upwards a

digit

Activation of the RIGHT key

Gives confirmation to the

present digit and shifts the cursor

to the next digit of the number.

Number setting

Menu managing

YES

Answer to a question

Activation of the LEFT key

Cyclical scroll of the available

options of a menu

Activation of the RIGHT key

Confirme the choice and entry

into the lower menu

User transmitter use guide

The standard transmitters ( called USER Transmitters ) are

memorised making use of the MASTER transmitter ( in

single mode or by blocks ).

The USER transmitter keys activate the relays according

to the memorised configuration.

During the normal use, the simultaneous activation of

both the keys of the transmitter is disabled.

This facility is only used during the programming

procedure ( see pag. 8 ).

Keypad use guide

The receiver can be programmed using the transmitter

DIGIKEY, called KEYPAD.

See. Fig. 3 the corrispondence between the transmitter

keys and the Keypad keys.

Keypad key (1) = Transmitter left key

Keypad key (2) = Transmitter right key

Fig. 3

Keypad key (0) = Transmitter left+right key

Pag. 6

123456789

0-(12/24)CNO CNO NF

Fig. 9

Fig. 8

!Position the receiver on a plane, open it and

remove the pre-forated parts (fig. 4) situated at the

back of the receiver with the aid of a screwdriver.

!Make a hole in the pre-forated parts ( 5) (fig. 6).

!Put the plugs in the holes (fig. 7) or adapt the holes

to the nature of the support.

!Fix the receiver using the screws supplied (fig. 8).

!Make holes in the guiding slits (only in those used),

!Proceed to the electric connection (fig. 10), and

thread the wires through the guiding slits (fig. 9).

ERONE advice

When assembling the equipment outdoors, we advise you to

protect the receiver in a container with an IP54 level of

protection.

Electrical connections

ERONE advice

A telephone wire (0.6 mm ) is sufficient for the input of the

receiver and the relay cabling.

Receiver power supply:

- connecting clip 3: 0V

- connecting clip 4: 12/24 Vac/dc

Connect the output contacts:

- connecting clip 5: common relay 1

- connecting clip 6: NO contact relay 1 (contact normally

open)

- connecting clip 7: common relay2

- connecting clip 8: NO contact relay 2 (contact normally

open)

- connecting clip 9: NC contact relay 2 (contact normally

closed)

Connect the antenna

- connecting clip 1: antenna conductor or antenna wire

supplied with the receiver

Installation

Fig. 4 Fig. 5

Fig. 6 Fig. 7

Fig. 10

ERONE advice

The installation and positioning of the antenna are

fundamental for good reception. Carry out tests

before fixing the antenna definitively. Place the

antenna as high as possible and far from all types of

metal structures which could shield the receiving part

of the antenna.

Pag. 7

Transmitter programming

The configuration of the receiver is possible only after the

memorization of one or more MASTER transmitters.

If the memory is empty, follow the following procedure:

Connect the power-supply and switch on the receiver. On

the display will appear the initial message.

The initial message can be different depending upon the

password configuration ( see procedure on pag. 15 for the

password setting).

The receiver is sold with a default value of the password :

( “11111”).

E R O N E 4 3 3 / 8 0 0

This symbol stands for

“Password enabled” See pag. 15

E R O N E 4 3 3 / 8 0 0

W E L C O M E

If the initial message has the “Welcome” instead of the

key symbol, it means that the password has been reset

( “00000”).

MASTER transmitter memorization

Push simultaneously the keys LEFT and RIGHT of a MASTER

transmitter .

On the display appears the following message:

S N 0 0 0 0 0 E R L ½ K Y A

S T O R E M A S T E R ?

Where 00000 is the Serial Number of the Master

transmitter used.

With an answer YES, the display shows “ EXECUTED OK”

and the transmitter is memorized.

On the first line of the display is present the information of

the abilitation of the whole transmitter, the relays activated

( 1 or 2 or ½” both” ) and the corresponding transmitter

keys : see pag. 10.

With an answer NO there is the return to the initial

message.

Main menu structure

The menu is organized into different levels, with a main

level and several lower levels. Once composed the right

password you entry into the main level.

See below the structure of the main level with the different

lower options.

ERONE 433/800

00000

FREE MEMORY

0000

DELETE

MODIFY USER ?

COPY MEMORY ?

CONFIG

USER STORED 0000

EXIT ?

Welcome message

Password request

(1) Free Memory

situation and user

rmemorization menu

(2) Delete menu

(3) User modify

(4) Data display and

data transfer

(5) Configuration of

the receiver:

(password, relays,

etc.)

(6) Number of stored

users / exit

(*)

(*) : The welcome message changes according to the version

Pag. 8

USER transmitters memorization

The procedure begins at point (1) of the main menu.

S T O R E U S E R M E N U

U S E R S N 0 0 0 0 1

The cursor blinks under the first left digit of the Serial

Number to set.

For this operation there you can use 3 different methods:

1) With the TX MASTER

Scroll up the digit with the LEFT key ( cliclically ) and shift

right to confirm with the RIGHT key.

Push LEFT+RIGHT keys simultaneously to cancel and to go

back to the upper menu;

2) With the KEYPAD

Use the keys of the keypad to set the right number and shift

right to confirm with the key (#);

3) With the TX USER

Push the key B of the USER transmitter which has to be

memorized: its Serial Number will replace the default

number of the message. Then push the RIGHT key of the

MASTER transmitter.

Once set ( for instance) the S/N : 20160, as explained

above, the program will ask for the relay [ 1, 2 or ½ ] and

the keys configuration [ A,B,C,D].

U S E R S N 2 0 6 1 0

R E L A Y : ½ K E Y : A

Modify the parameters RELAY and KEY according to your

needs by using the MASTER transmitter.

The next step allows to choose a “single” or a “block”

memorization.

U S E R S N 2 0 6 1 0

S T O R E S I N G L E ?

With an answer “YES” to the above question this phase

ends and the message “EXECUTED OK” appears on the

display.

With an answer “NO” begins the procedure for the block

memorization: the display will show the S/N of the first

transmitter of the block.

Entry the number of TX with the TX MASTER

S T O R E 0 0 0 0 T X

A R E Y O U S U R E ?

Give the confirmation with the RIGHT Key of the MASTER

transmitter.

NOTE :

If the memory contains already any transmitter with S/N

included in the range of the block, the entire operation is

cancelled and on the display appears the following

message:

S N X X X X X R L X K Y X

S E R I A L E X I S T !

Where XXXXX is the Serial Number of the transmitter

already present in the memory, RL X is the relay activated

and KY X is the transmitter key associated.

U S E R S N 2 0 6 1 0

H O W M A N Y T X 0 0 0 0

The next question proposed is the number of transmtters of

the block.

Pag. 9

Menù : Delete

This procedure begins at the point 2 of the main menu.

Through this procedure it is possible to delete:

!A single USER

!All the USERS

!The whole memory ( Complete initialization of the

receiver memory )

The structure of this sub-menu is the following:

Item 2 of the main

Delete single user

Delete all the users

Complete initialization

of the memory

Use the LEFT key of the MASTER transmitter to scroll the

different choices and select the operation to do with the

RIGHT Key.

Use both keys of the MASTER transmitter to return back

to the main menu.

Single user cancellation

With this choice you are asked for the Serial Number of

the transmitter to delete:

D E L E T E U S E R / M E M

U S E R S N 2 0 6 0 9

Entry the S/N using one of the methods of pag.8 ( TX

Master, KEYPAD or key B of the transmitter to delete ,

where possible).

Finally will appear the message:

D E L E T E S N 2 0 6 0 9

A R E YOUSURE

In this case with an answer YES the transmitter with S/N

20609 will be deleted and both the parameters “free

memory” and “stored TX number” will be updated.

DELETE USER/MEM?

USER

DELETE USER/MEM?

ALL USER

DELETE USER/MEM?

INIZIALIZE RX

DELETE USER/MEM?

ALL USER

All users cancellation

This option allows to delete all the USER transmitters and

to keep in the memory the MASTER transmitters.

D E L E T E U S E R / M E M

A L L U S E R ?

A further confirmation is required to finish the procedure

D E L A L L U S E R

A R E YOUSURE?

With a final YES, the cancellation will be carried out the

message “EXECUTED OK” appears on the display and

the receiver returns to the initial message.

Complete initialization of the receiver

With this option the following actions are carried out:

- cancellation of all the USER transmitters;

- cancellation of all the MASTER transmitters;

- cancellation of the current password and restore of the

default password ( “11111”).

- Restore at “0800 / 1619” of the free memory number

- Reset to “0000” of the stored transmitter number.

D E L E T E U S E R / M E M

I N I Z I A L I Z E R X ?

With the answer YES you are asked for a further

confirmation:

I N I Z I A L I Z E R X

A R E YOUSURE?

With a final YES the memory is completely cancelled, the

message EXECUTED OK appears and the receiver

returns to the initial message.

Pag. 10

Menu : Modify User

This procedure is at the item 3 of the main menu.

Through this procedure it is possible to carry out the

following actions on a USER transmitter, only if it is present

in the memory:

!Modify the activated relay and the corresponding

transmitter key;

!Enable or disable the single USER

M O D I F Y U S E R

U S E R S N 2 0 6 0 9

Set the Serial Number of the transmitter to modify by

using the 3 methods allowed ( TX MASTER, KEYPAD, Key

B of the USER TX )

Then give the confirmation with the key YES of the TX

MASTER

User Enable / Disable

The receiver checks the current situation and propose the

corresponding changement

- If the USER transmitter id enabled, it asks to disable;

- if the USER transmitter is enabled, it asks to enable

U S E R S N 2 0 6 0 9

D I S A B L E U S E R ?

U S E R S N 2 0 6 0 9

E N A B L E U S E R ?

With a final YES appears the message EXECUTED OK,

the transmitter is disabled, the procedure ends and the

program returns to the main menu.

If the transmitter is currently disabled, you are asked to

enable.

With an answer YES the following message appears:

D I S A B L E U S E R

A R E Y O U S U R E ?

With a final YES appears the message EXECUTED OK,

the transmitter is enabled, the procedure ends and the

program returns to the main menu.

With an answer YES the following message appears:

E N A B L E U S E R

A R E Y O U S U R E ?

Modify relay or key parameters

Once selected the Serial Number of the transmitter to

modify, you are asked to set the relay and the key

parameters:

U S E R S N 2 0 6 0 9

R E L A Y O R K E Y ?

With a YES,it is displayed the current configuration of the

transmitter: activated relay and corresponding transmitter

key.

The following table shows the association between relays

and keys when the parameter RELAY is set to ½:

2-keys transmitter

Key Option A B

Activations A - Relay 1 B - Relay 1

B - Relay 2 A - Relay 2

4-keys transmitter

Key Option A B C D

Activations A -Relay 1 B -Relay 1 C -Relay 1 D -Relay 1

B -Relay 2 C -Relay 2 D -Relay 2 A -Relay 2

If the parameter RELAY is set to 1 or 2, only the key

indicated causes the activation of the relay.

U S E R S N 2 0 6 0 9

R E L A Y : ½ K E Y : A

Once inside the options for the parameters RELAY and

KEY, scoll the options available with the LEFT key of the

TX MASTER and confirm with the RIGHT key.

OPTIONS RELAY : 1 - 2- ½ - 1- 2 - etc.

OPTIONI KEY : A - B - C - D - A - B - etc.

At the end the message EXECUTED OK appears and the

program returns to the main menu.

NOTE : If you entry the S/N of a transmitter not in

memory, the following message appears :

S N N O T I N M E M O R Y

U S E R S N 2 0 6 0 9

This manual suits for next models

Table of contents

Other Erone Receiver manuals

Erone

Erone SEL2641 R433-Z2 User manual

Erone

Erone SEL2641 433 Z1 User manual

Erone

Erone SEL2641R433-GDR Technical specifications

Erone

Erone SEL2641F433-Z4 User manual

Erone

Erone CDVI ERMU Technical specifications

Erone

Erone SEL128R433-NN User manual

Erone

Erone SEL2641R433-IP User manual

Erone

Erone SEL2641R433-PP4 User manual

Erone

Erone EL2641 R433-IP User manual

Erone

Erone SEL2641R433-BD4 Technical specifications

Erone

Erone SEL2641R433-TW User manual

Erone

Erone SEL39R433-M1 User manual

Erone

Erone SEL2641R433-C4R Technical specifications

Erone

Erone SEL2641 R433-Z4 User manual

Erone

Erone SELCD4A User manual

Erone

Erone SEL 39 R27-M1 User manual

Erone

Erone SEL2641R433-S1 User manual

Erone

Erone SEL2641R433-I User manual

Erone

Erone SEL2641R433-S0 User manual

Erone

Erone SEL2641R433-OC4 User manual

Erone

Erone SEL2641R433C2V Technical specifications

Erone

Erone SEL2641R433-S2 User manual

Erone

Erone SEL2641R433-S1 User manual

Erone

Erone 433 Z2 Series User manual

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual