Epson Equity 386/25 User manual

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference ln a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio or

television reception. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause interference to radio and television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will

invalidate the FCC Certification of this device and may cause interference levels which

exceed the limits established by the FCC for this equipment. It is the responsibility of the

user to obtain and use a shielded equipment interface cable with this device. If this

equipment has more than one interface connector, do not leave cables connected to unused

interfaces.

Changes or modifications not expressly approved by Epson America, Inc., could void the

user’s authority to operate the equipment.

FOR CANADIAN USERS

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus as set out in the radio interference regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de Classe B prescrites dans le règlement sur le

brouillage radioélectriques édicté par le Ministère des Communications du Canada.

IMPORTANT NOTICE

DISCLAIMER OF WARRANTY

Epson America makes no representations or warranties, either express or implied, by

or with respect to anything in this manual, and shall not be liable for any implied

warranties of merchantability and fitness for a particular purpose or for any indirect,

special, or consequential damages. Some states do not allow the exclusion of

incidental or consequential damages, so this exclusion may not apply to you.

retrieval system, or transmitted, in any form or by any means, electronic, mechanical,

photocopying, recording, or otherwise, without the prior written permission of Epson

America, Inc. No patent liability is assumed with respect to the use of information

contained herein. While every precaution has been taken in the preparation of this

publication, Epson America assumes no responsibility for errors or omissions. Nor is

any liability assumed for damages resulting from the use of the information contained

herein. Further, this publication and features described herein are subject to change

without notice.

TRADEMARKS

Epson is a registered trademark of Seiko Epson Corporation.

Equity is a registered trademark of Epson America, Inc.

General notice: Other product names used herein are for identification purposes only

and may be trademarks of their respective companies.

Torrance, California

Y70799100100

IMPORTANT SAFETY INSTRUCTIONS

Read all of these instructions and save them for later reference.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not

use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

Do not use this product near water.

Do not place this product on an unstable cart, stand, or table.

The product may fall, causing serious damage to the product.

Slots and openings in the cabinet and the back or bottom are

provided for ventilation; to ensure reliable operation of the

product and to protect it from overheating, these openings must

not be blocked or covered. The openings should never be blocked

by placing the product on a bed, sofa, rug, or other similar surface.

This product should never be placed near or over a radiator or

heat register. This product should not be placed in a built-in

installation unless proper ventilation is provided.

This product should be operated from the type of power source

indicated on the marking label. If you are not sure of the type of

power available, consult your dealer or local power company.

This product is equipped with a 3-wire grounding-type plug, a

plug having a third (grounding) pin. This plug will only fit into a

grounding-type power outlet. This is a safety feature. If you are

unable to insert the plug into the outlet, contact your electrician

to replace your obsolete outlet. Do not defeat the purpose of the

grounding-type plug.

Do not locate this product where the cord will be walked on.

10. If an extension cord is used with this product, make sure that

the total of the ampere ratings on the products plugged into the

extension cord do not exceed the extension cord ampere rating.

Also, make sure that the total of all products plugged into the

wall outlet does not exceed 15 amperes.

. . .

111

11. Never push objects of any kind into this product through cabinet

slots, as they may touch dangerous voltage points or short out

parts that could result in a risk of fire or electric shock. Never

spill liquid of any kind on the product.

12. Except as specifically explained in the User’s Manual, do not

attempt to service this product yourself. Opening or removing

those covers that are marked “Do Not Remove” may expose you

to dangerous voltage points or other risks. Refer all servicing in

those compartments to service personnel.

13. Unplug this product from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

A. When the power cord or plug is damaged or frayed.

If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

If the product does not operate normally when the operating

instructions are followed. Adjust only those controls that

are covered by the operating instructions, since improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to normal operation.

If the product has been dropped or the cabinet has been

damaged.

If the product exhibits a distinct change in performance,

indicating a need for service.

Contents

Introduction

Optional Equipment .................................

Operating Systems and Other Software ..................

VGA Utilities ......................................

How to Use This Manual .............................

Where to Get Help ..................................

Chapter 1

Setting Up Your System

1 Choosing a Location ...............................

1-1

2 Removing the Protector Card. .......................

1-3

3 Connecting a Monitor .............................

1-4

Using the VGA Interface .........................

1-4

Using a Display Adapter Card .....................

1-7

4 Connecting a Printer or Other Device. ................

1-8

Using the Parallel Interface .......................

1-8

Using the Serial Interface. ........................

1-11

5 Connecting the Keyboard. ..........................

1-12

6 Connecting the Mouse .............................

1-13

7 Connecting the Power Cord ..........................

1-15

8 Turning On the Computer ..........................

1-16

Turning Off the Computer. .......................

1-18

Chapter 2

Running the Setup Program

Automatic Configuration .............................

2-2

Starting the Setup Program. ...........................

2-2

Continuing From an Error Message .................

2-4

Moving the Cursor Block .........................

2-6

Setting the Display Adapter Type. ......................

2-7

Setting the Power-on Password .........................

2-9

Setting the Extended Memory Caching ..................

2-12

Setting the Processor Speed ...........................

2-14

Setting the Keyboard and Speaker Options ...............

2-15

Setting the Real-time Clock ...........................

2-17

Setting the Hard Disk Drive Configuration ...............

2-20

Hard Disk Drive Types ...........................

2-24

Setting the Diskette Drive Type(s). .....................

2-26

Setting the Serial/Parallel Interfaces. ....................

2-27

Reviewing Your Settings. .............................

2-29

Leaving the Setup Menu ..............................

2-31

Chapter 3 Using Your Computer

Installing MS-DOS or Another Operating System .........

3-1

Copying the Reference and Utility Files. .................

3-2

Special Keys on the Keyboard. .........................

3-3

Stopping a Command or Program. ......................

3-5

Resetting the Computer ..............................

3-5

Using a Power-on Password. ...........................

3-7

Changing a Power-on Password ....................

3-8

Deleting a Power-on Password ..................... 3-9

Using Disks and Disk Drives ........................... 3-10

How Disks Store Data............................ 3-10

Types of Diskette Drives. ......................... 3-12

Caring for Diskettes and Diskette Drives ............. 3-14

Write-protecting Diskettes. ....................... 3-16

Using a Single Diskette Drive System ............... 3-18

Inserting and Removing Diskettes .................. 3-19

Formatting Diskettes.............................

3-21

Making Backup Copies ...........................

3-21

Using a Hard Disk Drive..........................

3-22

Chapter 4

Enhancing System Operations

Using AUTOEXEC.BAT and Other Batch Files. ..........

4-1

Changing the Processor Speed .........................

4-2

Entering Keyboard Commands. ....................

4-4

Using the ESPEED Program. ......................

4-5

Reassigning the Diskette Drives ........................

4-7

Using the AFDD Program ........................

4-8

Using Your Computer as a Network Server ...............

4-9

Using a Password in Network Server Mode ...........

4-11

Using Expanded Memory Beyond 640KB. ................

4-12

Using Special VGA Features. ..........................

4-13

Chapter 5

Installing and Removing Options

Removing the Cover. ................................

5-2

Changing the Jumper Settings .........................

5-6

Setting the Jumpers. .............................

5-7

Installing an Option Card .............................

5-10

Removing an Option Card ............................

5-15

Adding Memory Modules .............................

5-16

Installing Memory Modules .......................

5-17

Removing Memory Modules. ......................

5-22

Installing a Math Coprocessor. .........................

5-25

Removing a Math Coprocessor. ........................

5-30

Replacing the Cover .................................

5-30

Post-installation Setup ...............................

5-32

Appendix A

Using the VGA Utilities

Preparing to Install Drivers or Utilities ................... A-4

Using the VGA Driver Setup Program ................... A-4

Microsoft Windows/286, Versions 2.03, 2.10, and 2.11 ...... A-8

Microsoft Windows/386, Versions 2.03, 2.10, and 2.11 ...... A-10

Microsoft Windows, Version 3.0. .......................

A-l 1

vii

Microsoft/IBM OS/2 Presentation Manager,

Versions 1.1 and 1.2 ............................... A-13

Microsoft Word,Version 5.0 ........................... A-15

Autodesk AutoCAD, Version 2.62. ..................... A-16

Autodesk AutoCAD, Version 9.00. ..................... A-18

Autodesk AutoCAD, Version 10.0. ..................... A-20

Autodesk AutoCAD 386, Version 10.0 .................. A-23

Autodesk AutoCAD, Version 10.0 (Fast Display List) ...... A-25

Digital Research GEM, Version 2.2 ..................... A-27

Digital Research GEM, Version 3.0 ..................... A-29

Ventura Publisher, Versions 1.0 and 1.1 ..................

A-31

Ventura Publisher, Version 2.0 ......................... A-33

Lotus 1-2-3, Release 2.0 and Lotus Symphony,

Releases 1.0, 1.1, and 2.0 ........................... A-34

Ashton-Tate Framework II, Release 1.0 .................. A-37

WordStar, Version 3.3. ............................... A-39

WordStar, Versions 4.0 and 5.0 ........................

A-41

WordPerfect, Versions 4.0 and 4.1 ...................... A-43

WordPerfect, Version 5.0 ............................. A-44

VersaCAD Design, Version 5.4. ........................ A-46

VersaCAD 386, Version 5.4 ........................... A-48

CADVANCE, Version 3.50 ........................... A-49

OrCAD, Version 3.22 ................................

A-51

Generic CADD, Version 1.1, Level 3. ................... A-52

VESA Driver, Version 1.0. ............................ A-54

Using SETVESA ............................... A-55

Using VTEST .................................. A-56

Utility Programs .................................... A-57

VGAMODE Utility ............................. A-57

SETVGA Utility ............................... A-59

MODETEST Utility. ............................ A-62

WS33INST Utility .............................. A-63

SNOOZE Utility. ............................... A-63

*..

VIII

Other manuals for Equity 386/25

This manual suits for next models

Table of contents

Other Epson Desktop manuals

Epson

Epson Equity 386SX/16 PLUS User manual

Epson

Epson ActionPC 2000 Instruction sheet

Epson

Epson Equity 286 PLUS Dimensions

Epson

Epson Powerspan Installation and operation manual

Epson

Epson Powerspan 2 User manual

Epson

Epson Equity 386/25 PLUS Dimensions

Epson

Epson NX Installation and operation manual

Epson

Epson Equity 386SX PLUS Installation and operation manual

Epson

Epson Equity 386/33 PLUS Dimensions

Epson

Epson Equity 386/33 PLUS Installation and operation manual

Epson

Epson Equity III User manual

Epson

Epson Equity 4 Installation and operation manual

Epson

Epson Equity 386/25 Dimensions

Epson

Epson Proper Method for Running Benchmark and Diagnostics... Dimensions

Epson

Epson ActionPC 5500 User manual

Epson

Epson Endeavor VL User manual

Epson

Epson EQUITY II+ Dimensions

Epson

Epson ActionDesk 4000 Dimensions

Epson

Epson Endeavor L User manual

Epson

Epson PX-8 User manual

Epson

Epson Equity 386/25 PLUS Installation and operation manual

Epson

Epson ActionPC 5000 User manual

Epson

Epson LT-286 User manual

Epson

Epson Endeavor Pro User manual

Popular Desktop manuals by other brands

HP m9060n - Pavilion - Elite Quick setup

Asus

Asus E210 Series user guide

Dell

Dell Inspiron 600m quick start

Dell

Dell Inspiron 3662 Service manual

TotalFlow

TotalFlow uFLO user manual

HP Presario SV7000 - Desktop PC manual

HP ProDesk 400 G5 Maintenance and service guide

Logitech

Logitech MK320 quick start guide

Dell

Dell XPS 730 H2C Service manual

Sony

Sony Vaio Series operating instructions

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer quick start

Alto

Alto MD 250 instruction manual

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series user manual

Sony

Sony VAIO VGX-TP1 Series user guide

Asus

Asus Eee Box B204 user manual

Dell

Dell Optiplex 9010 All In One owner's manual