Epson Endeavor User manual
EPSON
®
VGA Utilities Guide
This manual is printed on recycled paper and is
l00% recyclable.
IMPORTANT NOTICE
DISCLAIMER OF WARRANTY
Epson America makes no representations or warranties, either express or implied, by or
with respect to anything in this manual, and shall not be liable for any implied warranties
of merchantability and fitness for a particular purpose or for any indirect, special or
consequential damages. Some states do not allow the exclusion of incidental or
consequential damages, so this exclusion may not apply to you.
COPYRIGHT NOTICE
All rights reserved.
No
part
of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means,
electronic, mechanical
photocopying, recording, otherwise,
without the prior written permission of Epson
America, Inc. No patent liability is assumed with respect to the use of information
contained herein. Nor is any liability assumed for damages resulting from the use of the
information contained herein. Further, this publication and features described herein are
subject to change without notice.
TRADEMARKS
Epson is
a registered trademark of Seiko Epson Corporation.
General notice: Other product names used herein are for identification purposes only and
may be trademarks of their respective companies.
Copyright © 1993 by Epson America, Inc.
Torrance,Califomia 400195000
ii
Contents
Introduction .............................
1
Installing Drivers and Utilities
...................
5
Using the INSTALL Program
...................
6
AutoDesk Products
.........................
8
Installing the Drivers
.....................
10
Configuring Your Auto Desk VGA Environment
.....
10
Using FASTACAD.BAT
....................
11
Configuring VGA Colors
...................
11
Configuring AutoCAD, Versions 9,10,11
.........
13
Configuring AutoCAD, Version 12
.............
14
Configuring AutoShade with RenderMan
.........
15
Configuring AutoDesk 3D Studio
..............
16
Framework II
.............................
17
Copying Framework II Drivers. ...............
18
Installing the Drivers
.....................
18
Framework III
............................
20
GEM,Version 3.x
..........................
22
Creating a GEM Driver Pack
.................
22
Installing the Drivers
.....................
23
Configuring GEM for the New Drivers
...........
24
IBM OS/2, Version 2.0
.......................
25
Installing the Drivers
.....................
25
Configuring OS/2 for the VGA Drivers
...........
26
Lotus l-2-3 or Symphony, Version 2.x
..............
28
Lotus l-2-3,Version 3.x
.......................
29
Microsoft Windows, Version 3.0
..................
31
Installing the Drivers
.....................
31
Configuring the Drivers
....................
32
Modifying the SYSTEM.INI FiIe
...............
34
Microsoft Windows, Version 3.1
..................
35
Installing the Drivers
.....................
35
Configuring the Drivers
....................
36
MicrosoftWord,VersionS.O ....................
37
PCad .................................
39
Ventura Publisher ..........................
40
VersaCAD386 ............................
42
VersaCAD 2D
............................
43
WordPerfect,VersionS.O
......................
45
WordPerfect, Version 5.1
......................
46
WordStar ...............................
47
VGAUtilities ............................
48
CLMODE
............................
48
SetRES
..............................
52
iv
The Utility diskettes included with your system contain special
VGA (video graphics array) drivers and utilities for your
computer’s built-in VGA adapter. This booklet describes how
to install and use these drivers and utilities.
Since software programs can run on different types of display
adapters with different types of monitors, the VGA drivers
identify your display adapter and monitor for the software.
These drivers are files your software uses to communicate with
your display adapter and monitor.
A utility is a program that supports the processes of a
computer. The utilities on your diskettes let you change the
screen resolution and enhance your system operation by
controlling the screen refresh rate or setting various video
modes. You can also use the CLMODE utility to see how much
video memory is installed in your computer.
Your computer’s built-in VGA adapter is 100% compatible with
IBM VGA. This adapter allows you to use the computer with
Epson
®
VGA monitors, other brands of VGA monitors, and
VGA compatible, multifrequency monitors that use analog
input. The drivers and utilities described in this guide work
with any of these monitors.
Standard VGA monitors display resolutions up to 640 x 480,
and you do not need to install the drivers or utilities for your
monitor to operate properly with your application programs at
this resolution. Also, your system supports the VESA standard
1.20. If you have programs that use VESA, install the VESA
drivers that came with these programs.
VGA Utilities 1
However, you need to install these drivers if you want to use
resolutions over 640 x 480 or take advantage of the following
special features:
Interlaced and non-interlaced resolutions up to 1024 x 768
in graphics modes with up to 16.8 million colors in
640 x 480 resolutions; check the table on page 3 for
resolutions and colors supported for your applications
132-column text mode in 16 colors
High speed video memory interface
16-bit data path to video memory and hardware registers
Video adapter control of graphics cursor movement.
Note
You can use Epson’s VGA drivers and utilities only with the
computer’s built-in VGA adapter. If you have installed an
optional display adapter card, use
the drivers
and
documentation that came with it.
These programs are designed for systems running MS-DOS
or OS/2. If you are using another operating system, see the
documentation that came with it for information about the
VGA drivers you can use.
Your computer comes with either 512KB or 1MB of video
memory installed on the system board. If your system has
512KB, you can upgrade the video memory to 1MB by
installing four additional video memory chips. (See Chapter 2
of the
User’s
Guide for installation instructions.) The resolutions
your system can support for each application depend on the
size of your video memory.
2 VGA Utilities
The following table lists the applications for which high
resolution VGA drivers are provided, as well as the supported
resolutions and colors for each application. Those drivers
requiring 1MB of video memory are identified in the last
column.
Supported applications
VGA Utilities 3
Supported applications (Continued)
In addition to the drivers for the applications listed above, the
Utility diskettes include INSTALL programs to help you install
the drivers on your hard disk.
The Utility 1 diskette contains VGA drivers for MS-DOS based
applications. The Utility 2 diskette contains drivers and utilities
for Windows 3.0 and 3.1. The Utility 3 diskette contains VGA
drivers and utilities for the OS/2 environment.
4 VGA Utilities
You’ll also find the following utility programs:
CLMODE
SetRES.
The CLMODE utility allows you to see the amount of video
memory you have installed, determine the video modes you
want to use, and change the vertical refresh rates. The SetRES
utility allows you to change your screen resolutions from
within the Windows environment.
You may want to install these utilities even if you are not
installing any of the VGA drivers. See page 48 for more
information.
Installing Drivers and
Utilities
The information in this guide is organized alphabetically by
application program or operating environment. To install a
particular driver, look up your application or environment in
the table of contents; then turn to the appropriate section for
instructions. When you are instructed to run the INSTALL
program, see the section below.
Note
Each of the Epson VGA drivers is designed to work with a
specific version of software. Make sure the driver you select
is compatible with the version of software you are using, or
you may get unpredictable results.
VGA Utilities 5
Using the INSTALL Program
The INSTALL program on your Utility 1 diskette provides an
easy way to install the VGA drivers and utilities for your
MS-DOS based applications. You can choose to install of the
drivers at once or select individual sets of drivers to install.
Note
You do not need to use the INSTALL program on the
Utility 1 diskette to install the 0S/2 and Windows drivers.
See “IBM OS/2, Version 2.0” on page 25 or “Microsoft
Windows, Version 3.0” on page 31 for installation
instructions for these drivers.
Follow these steps to run INSTALL:
1.
Insert the Utility 1 diskette in drive A.
2.
Type
A:
and press to log onto drive A.
3.
Type the following and press to start the installation
program:
INSTALL
You see the Cirrus Logic copyright screen.
4.
Press . The INSTALL program prompts you to select
the drive where you want to install the drivers.
5.
Press again to accept the default or use the arrow keys
to move the cursor to the drive you want to select and press
6 VGA Utilities
Other manuals for Endeavor
4
Table of contents
Other Epson Desktop manuals
Epson
Epson Stylus Pro 5000 - Print Engine Installation and operation manual
Epson
Epson Endeavor 486I Installation and operation manual
Epson
Epson Apex 110 User manual
Epson
Epson QX-10 User manual
Epson
Epson Endeavor 468C User manual
Epson
Epson ActionPC 2000 User manual
Epson
Epson EL 486UC+ Installation and operation manual
Epson
Epson Endeavor Installation and operation manual
Epson
Epson ColorCopy Station 8200 User manual
Epson
Epson CW3S16 Canadian Product User manual
Epson
Epson Equity 486SX/25 PLUS Installation and operation manual
Epson
Epson Equity 386/33 PLUS Dimensions
Epson
Epson EQUITY II+ User manual
Epson
Epson EL 3S/33 Dimensions
Epson
Epson Proper Method for Running Benchmark and Diagnostics... Dimensions
Epson
Epson ActionPC 7300 User manual
Epson
Epson NX User manual
Epson
Epson Apex 110 Dimensions
Epson
Epson ActionTower 8000 User manual
Epson
Epson ActionDesk 4000 User manual
