EP Solar LS1024BP User manual

LS1024BP/ LS2024BP

——Solar Charge Controller

Thank you very much for selecting our product!

This manual offers important information and

suggestions with respect to installation, use and

troubleshooting, etc. Please read this manual carefully

before using the product and pay attention to the

safety recommendations in it.

EPSOLAR

USER MANUAL

LS1024BP/ LS2024BP

——Solar Charge Controller

Nominal system voltage 12 / 24VDC*

Maximum PV input voltage 50V

Nominal charge / discharge current

LS1024BP 10A

LS2024BP 20A

*The solar charge controller has the system voltage 12/24V automatic

recognition function and custom define function, and all charge,

discharge and load control parameters can be modified.

Warranty: The charge controller is warranted to be free from defects

for a period of two years from the date of shipment to the original end

user.

Notice: Manufacture is not responsible for the damage of any

part of controller due to operator's misuse, battery parameters

mismatch, unreasonable system configuration, unauthorized

repairment or exceeding the specified parameter.

LandStar

Contents

1 Important Safety Information..................................1

2 General Information................................................1

3 Installation Instructions...........................................2

3.1 General Installation Notes........................2

3.2 Wiring..........................................................3

4 Operation..................................................................4

4.1 LED Indicators...........................................4

4.2 Setting Operation......................................5

5 Protection, Troubleshooting...................................6

5.1 Protection...................................................6

5.2 Troubleshooting.........................................7

6Technical Specifications..........................................9

1 Important Safety Information

Please inspect the controller thoroughly after it is delivered. If any

damage is seen, please notify the shipping company or our company

immediately.

2 General Information

LandStar BP series solar charge controller adopts the most advanced

digital technique and operates fully automatically. It’s Ideal for extreme

environments with corrosion, dust, water etc and has various unique

functions：

12V/24V automatic identify or user-defined working voltage.

High efficient Series PWM charging, increase the battery lifetime and

improve the solar system performance.

Use MOSFET as electronic switch, without any mechanical switch.

Multiple load control modes, increase the flexibility of the load output

Gel, Sealed, Flooded and user-defined battery type option.

Adopt temperature compensation, correct the charging and

discharging parameters automatically and improve the battery

lifetime.

New SOC method of calculating accurately displays the available

battery capacity.

LandStar BP has no keys , The control function and the switch

condition of the load can be modified by communication connection.

Electronic protection: Overheating, over charging, over discharging,

overload, and short circuit.

Reverse protection: any combination of solar module and battery.

With functions of current power calculation and real-time energy

statistics recording, it is convenient for users to view charging and

discharging energy of each day, month, year and total value.

Use of standard Modbus communication protocol for TTL-232 bus

connections, communication protocol compatibility much better

Support firmware upgrade

Fully encapsulated PCB, IP67 protection

Aluminumhousing

3 Installation Instructions

3.1 General Installation Notes

Be very careful when working with batteries. Wear eye protection.

Have fresh water available to wash and clean any contact with

battery acid.

Never short circuit the battery positive and negative terminals and

wires which may cause explosion or fire.

Install external fuses/breakers as required.

Disconnect the solar module and fuse/breakers near to battery

before installing or adjusting the controller.

Confirm that power connections are tightened to avoid excessive

heating from loose connection.

Uses insulated tools and avoid placing metal objects near the

batteries.

Explosive gasses may be present during charging. Be certain there is

sufficient ventilation to release the gasses.

Loose power connections and/or corroded wires may result in

resistive connections that melt wire insulation, burn surrounding

materials, or even cause fire. Ensure tight connections and use

cable clamps to secure cables and prevent them from swaying in

mobile applications.

Only charge the batteries that comply with the parameters of

controller.

Battery connection may be wired to one battery or a bank of batteries.

The following instructions refer to a singular battery, but it is implied

that the battery connection can be made to either one battery or a

group of batteries in a battery bank.

3.2 Wiring

1. Connect components to the charge controller in the sequence as

shown above picture and pay much attention to the “+”（Red）and

“-“（Black）.Always power the battery First.

2. After power the battery, check the battery indicator on the controller,

it will be green. If it’s not green, please refer to chapter 5.

3. The battery fuse should be installed as close to battery as possible.

The suggested distance is within 150mm.

4 Operation

4.1LED Indicators

Battery Status LED indicator

Charging Status LED indicator

Indicator Status Description

Green

On Solid

Normal

Green

Slowly

Flashing

In charging

Green

OFF

No charge

Green

On Solid

Normal

Green

Slowly

Flashing

Full

Green

Fast Flashing

Over voltage

Orange

On Solid

Under voltage

Red

On Solid

Over discharged

Red

Flashing

Battery over

temperature

Charging and battery indicator

(red)flashing simultaneously

System voltage

error

Charging and battery

indicator(orange)flashing

simultaneously

Controller

overheating

4.2Setting Operation

Three methods to program the controller:

1–Remote Meter,MT50/MT100(Use dedicated TTL232 to RS485

communication cable with CC-TTL-RS485-200U）.

2–Super Parameter Programmer, SPP-01(Use dedicated TTL232 to

TTL232 communication cable with CC-TTL-TTL-150U）.

This method can realize one-key setting operation which is suitable for

bulk quantity products setting or applied in the projects.

3–PC monitoring setting software “Solar Station Monitor” （Use

dedicated TTL232 to USB communication cable with

CC-USB-TTL-150U）.

Through the remote meter and PC software, it can realize real-time

monitoring, modification of control parameter, charge mode, load work

mode, inquiry of failure information etc.

This manual suits for next models

Table of contents

Other EP Solar Controllers manuals

EP Solar

EP Solar Tracer-4210RN User manual

EP Solar

EP Solar EPHC Series User manual

EP Solar

EP Solar Tracer-2210RN User manual

EP Solar

EP Solar LandStar LS0524R User manual

EP Solar

EP Solar EPIP20-LT Series User manual

EP Solar

EP Solar LS0512R User manual

EP Solar

EP Solar eTracer Series User manual

EP Solar

EP Solar LS1024R User manual

EP Solar

EP Solar Tracer-1206RN User manual

EP Solar

EP Solar ViewStar MT-100 User manual

EP Solar

EP Solar Tracer1215BN User manual

EP Solar

EP Solar ViewStar Series User manual

EP Solar

EP Solar EPIPDB-COM series User manual

EP Solar

EP Solar LS1024RD User manual

EP Solar

EP Solar ET2415N User manual

EP Solar

EP Solar LS2024B User manual

EP Solar

EP Solar SS1024R User manual

EP Solar

EP Solar LandStar LS-EU Series User manual

EP Solar

EP Solar Tracer-3215RN User manual

EP Solar

EP Solar EPHC10-EC series User manual

EP Solar

EP Solar LS1024RP User manual

EP Solar

EP Solar eTracer ET4415BND User manual

EP Solar

EP Solar LS1024 User manual

EP Solar

EP Solar EPRC10-EC User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual