Eneo MPD-72M2812M0A User manual

User Manual

1/2.8” HD Dome, Fixed,

Day&Night, 1920x1080, WDR,

Infrared, 2.8-12mm, IP67

MPD-72M2812M0A

Safety Precaution

MPD-72M2812M0A

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent electric shocks and risk of fire hazards, do NOT use other than

specific power source.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

Caution :

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user

of the model requires continued operation during power mains interruptions, it is

recommended that the model be powered from an uninterruptible power supply

(UPS) or a battery.

MPD-72M2812M0A

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension

and may differ from actual video of the camera.

Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when laying the connection cable and observe that the cable

is not subjected to heavy loads, kinks or damage and no moisture can get in.

The warranty becomes void if repairs are undertaken by unauthorized persons.

Maintenance and repair have to be carried out only by authorized service centers.

Use only a mild detergent to clean the housing.

The camera should never be operated beyond the technical specifications.

This can lead to destruction.

The camera should never be operated in water.

MPD-72M2812M0A

Contents

Safety Precaution

p.03~04

Contents

p.05

Features

p.06

Composition

p.07

Dimensions

p.07

Part Names

p.08

Installation Instructions

p.09~12

Operating Instructions

p.13~29

Specifications

p.30

MPD-72M2812M0A

Features

Key Features

• Full-HD 2Mega pixel CAMERA, 1920x1080(30p/25p)

• The best low light performance with SONY’s STARVIS sensor

• Video output EX-SDI1.0,2.0 / HD-SDI / TVI mode / AHD mode / CVI mode

or CVBS Selectable

• TVI mode / AHD mode / CVI mode, Video Transmission Distance

over Coax.; 500M

• f=2.8~12mm F1.4, 5Mega pixel Motorized zoom lens

• Automatically removable IR Cut filter by Dual filter switcher

• SNAP Focus by Motorized Zoom lens

• Motorized Zoom & Focus Adjustment

• Sensitivity of Color 0.08 Lux(LED off), B/W 0.005 Lux (LED off)

• True WDR (Wide Dynamic Range), 30/25fps

• ROI (Region of Interest) WDR mode:

- Proper compensation of exposure for each inside and outside of

interested area.

- Better contrast and No motion ghost effect

• Improved Noise figure with the enhanced 3D-NR

• Motion Detection, Privacy Mask, Defog, Sens-up(~x32), ACE(D-WDR),

Sharpness, Mirror/Flip, BLC/HLC, Anti-Saturation, Smart IR, Title Set

• Top performance at low light sensitivity (Sens-up On)

• Selectable Digital output 1080p or 720p

• OSD Menu & Video Sub-out port for easy installation & maintenance

• Circuit protection against faulty connection in power polarity

• Isolated power supply against ground loop problem

• UTC control through HD-TVI (Pelco-C, Hikvision) / AHD

• Built-in 2pcs High power IR-LEDs

• 3-Axis gimbal

• Double side Anti-scratch hard coated clear bubble dome

• Flush mount (option: Surface mount and various adaptors)

• IP67 / IK10 protection

• AC24/DC12V Dual power

Composition

MPD-72M2812M0A

Dimensions

(unit : mm)

Mounting Template

Operating

InstructionDome Camera

Torque Wrench:

3mm (1pc)

Video Sub-out

Cable (1pc)

Mounting Screw:

4 x 30mm (3pcs)

Plastic Anchor:

6 x 30mm (3pcs)

PCD Ø120

119

Ø102

Ø140

MPD-72M2812M0A

Part Names

BUBBLE DOME

3-AXIS GIMBAL

DOME COVER

SAFTY WIRE

FLUSH MOUNT

LENS

POWER CABLE

VIDEO OUTPUT

POWER CABLE

[ BOTTOM VIEW ]

POWER SUPPLY

CONNECTOR

POWER

CABLE

OSD Menu Control board

MPD-72M2812M0A

Installation Instructions

• Surface mount

• Pole mount adaptor

• Tilted mount

• Wall mount

(Requires additional

Surface mount)

• Tilted junction mount

■ Optional Mounting Accessories

1. Locate the mounting template at the installation position and drill the ceiling

or wall if needed.

2. Open the dome cover by loosening screws(4x12mm). Use the torque wrench

supplied.

3. Set the camera’s viewing angle.

4. Put the dome cover to the dome base unit and tighten the assembly screws.

- Place the dome base unit on pre-drilled position and fix it through using mounting

screws (4x30mm).

- Route the power source cable and connect cables.

- In the case of installation with optional mounting accessories(Surface mount

or Tilted mount), the power cable should be fixed to the flush mount by using

the fixing screw and cable holder as illustrated.

Mounting Screw

(4x30mm)

Plastic Anchor

(6x30mm)

Torque

Wrench

MPD-72M2812M0A

Installation Instructions

■Option 2.

Installation with Surface mount / Tilted mount

■Option 1.

Installation with Flush mount / Tilted Junction mount

Cable Holder

Video Output

Cables

①Cable is unfixed on the Dome base.

②Connect the power cable to their repective connections.

①Cable is unfixed on the Dome base.

②Tie up the VIDEO OUTPUT cables with cable holder.

③Tie up the POWER SUPPLY cable with cable holder as illustrated.

④Connect the wiring connector to their repective connections.

Cable Holder

Power Supply

•In the case of installation with Flush/ Surface/ Tilted mount, IP protection

rating is not guaranteed.

• If power/video connectors are exposed to water or rain, separate protection

shield is essential.

CAUTION

Table of contents

Other Eneo Security Camera manuals

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications