Eneo IAM-6MC1001MTA User manual

EN
User Manual
Ethernet Coax Transmitter/Receiver,
Data & Power over Coax,
1 x RJ-45, 1 x BNC
IAM-6MC1001MTA
IAM-6MC1001MRA

Safety instructions
•Before switching on and operating the system, first read this safety advice and the operating instructions.
•Keep the operating instructions in a safe place for later use.
•Installation, commissioning and maintenance of the system may only be carried out by authorised individuals and in
accordance with the installation instructions - ensuring that all applicable standards and guidelines are followed.
•Protect the devices from water penetration and humidity, since these can cause lasting damage.
•Should moisture nevertheless enter the system, under no circumstance switch on the devices under these conditions,
instead send them for examination to an authorised specialist workshop.
•The system must never be used outside of the technical specifications, since this can destroy it.
• The device must be protected from excesses of heat, dust, humidity and vibration.
• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never pull directly on the
cable itself.
• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged and that no
humidity can penetrate into them.
• In the event of a malfunction, please inform your supplier.
• Maintenance and repairs may only be carried out by authorised specialist personnel.
• The system must be isolated from the power supply before opening the housing.
• The device may only be opened by qualified service personnel. Unauthorised access invalidates any warranty claim.
• Connection cables should always be exchanged through Videor E. Hartig GmbH.
• Use only original spare parts and accessories from Videor E. Hartig GmbH.
• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as these can
permanently damage the surface.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are not displaced
during installation. Damaged seals must not be installed and will invalidate any warranty.
• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing the cable outlets
with silicone.
• Wire end ferrules should be used when shortening the flexible connection cables.
• The devices may only be operated in the temperature range indicated in the data sheet and within the defined air humidity
range.
WEEE (Waste Electronical & Electronic Equipment)
Correct Disposal of This Product (Applicable in the European Union and other European countries with separate collection
systems).
This marking shown on the product or its literature, indicates that it should not be disposed
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from
other types of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take this
item for environmentally safe recycling. Business users should contact their supplier
and check the terms and conditions of the purchase contract. This product should
not be mixed with other commercial wastes for disposal.

1. Quick Installation Guide ..................................................................................... 3
1.1. Package Contents ..............................................................................................................................3
1.2. Overview ............................................................................................................................................3
1.3. Features............................................................................................................................................3
1.4. Hardware Overview ............................................................................................................................4
1.5. Product Installation Guide...............................................................................................................5
1.6. Product Application .........................................................................................................................5
1.7. Network Password Change ...............................................................................................................6
1.8. LED Indicators .....................................................................................................................................7
1.9. Specification ......................................................................................................................................7
1.10. Caution ............................................................................................................................................8
1.11. Warranty.........................................................................................................................................8
2. Pre-field verification ........................................................................................... 9
2.1. Check transmission line ....................................................................................................................9
2.2. Check grounding and potential difference ................................................................................14
2.3. Power supply availability .............................................................................................................15
2.4. Site environment review ..............................................................................................................15
3. Equipment Installation Guide .......................................................................... 16
3.1. Selection of installation equipment .............................................................................................16
3.2. Transmission rate / PoE output .................................................................................................18
3.3. PoE On / Off Setting.....................................................................................................................19
3.4. Joining (Network Grouping Password Setting) ........................................................................20
3.5. Daisy Chain Connection ..............................................................................................................25
3.6. Product power supply (DC adapter / PoE) ..................................................................................26
3.7. LED operating status ...................................................................................................................27
3.8. Grounding and Potential Difference ........................................................................................28
3.9. Apply Surge Protector ................................................................................................................28
4. Troubleshooting FAQ........................................................................................ 29
4.1. EPoC transmission equipment ....................................................................................................29
Contents

Quick Installation Guide — 3
1. Quick Installation Guide
1.1. Package Contents
EPoC Extender
(Transmitter/Receiver) Bracket & Screw Installation Guide
Quick Start
Guide
1.2. Overview
EPoC Extender is a High-Speed, long distance Ethernet & PoE extender that makes possible to transmit
the Ethernet signal up to 2.4Km and PoE up to 1.2Km via Coax (or UTP, 2wire & Etc.) cables in different situations.
It is cost-effective and time saving solution to migrate existing analog system to IP based system since
EPoC Extender supports easy installation utilizing the existing cable.
With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and
reduces the construction cost significantly compared with fiber optic configuration.
1.3. Features
•Ethernet over Coax communication following
IEEE1901 Standard
•Data + Power over Coax cable (or UTP, 2-Wire)
•Data distance up to 2.4Km
•PoE distance up to 1.2Km
•Max. 95Mbps Bandwidth
•10/100 Full Duplex
•128bit AES network encryption
•Supports Multi-connection (Daisy chain, Star, etc.)
•Slim design
•PoE, PoE+, Extra PoE (Max. 60W output) -
Transmitter model only
•Supports UTP, Telephone (2 Pairs), 2-Wire cable
communication (Using IAM-4MU1001M0A)
•LED Indication (PoE, Data, Join, Power)
•Plug & Play
•Surge Protection
•Support PoE+ Input (25.5W) from PSE devices (PoE
Switch or Injector) – Receiver model only

Quick Installation Guide — 4
1.4. Hardware Overview
Right
Left
56V DC
Bracket
NO ANALOG
CAMERA
ETHERNET
PoE-ON
Data-Link
Join-Link
Power
PoE
Bracket
Join
ON OFF
Bracket Hole
Bracket Hole
RJ45
Join Button
Status LED Indicator
DC Power Jack
PoE ON/OFF Switch
(Transmitter model
only)
PoE-ON (Transmitter model only)
PD-AUX (Receiver model only)

Quick Installation Guide — 5
1.5. Product Installation Guide
1. Set the IP address on the camera following the instruction manual of the camera.
hIf the camera IP is automatically assigned (DHCP, etc.), there is no need to set the camera IP separately.
2. Connect BNC of the coaxial cable to each Transmitter/Receiver.
3. Connect 56V DC power to Transmitter/Receiver first and then to AC outlet.
recommeded to use 56VDC Power supply on Receiver. When using both PoE switch Device and
hReceiver can be powered by PoE Switch Device (PoE+ PD Supported) but for safe working, it power supply
at the same time, power supply works preferentially.
hIn case of 7W camera, the device supports long distance PoE transmission up to 1,200m over RG6 coaxial
cable.
PoE transmission distance can be varied depending on cable type and Camera’s
power consumption(W).
4. When they are connected without any problem, Power / Join Link LED are on.
5. Adhere the brackets in the package to Transmitter/Receiver and then fix up the products.
6. Connect the UTP(LAN) cable between Receiver and NVR first and then between Transmitter and camera.
7. Turn on the PoE switch on Transmitter for PoE IP camera and if the camera is powered by a separate power
source (not powered by PoE output feature of the Transmitter), turn off the PoE switch on Transmitter.
hBoth Transmitter/Receiver send data and power together via BNC connector. Receiver does not have
PoE
support so that it can send data only via RJ45.
8. Ping test is recommended to confirm the whole network after installation.
9. Check the video signal on the monitor.
1.6. Product Application
AC/DC
Adapter(12V)
Non-PoE IP
Camera
Coaxial Cable
Coaxial Cable
10/100 Ethernet
10/100 Ethernet
Po E
Receiver
56V DC/1.2A
Power Supply
NVR
Transmitter Receiver
Transmitter
Po E
Camera
PoE Switch
PoE : OFF
PoE : ON
PoE
In put Power
DC Adapter
In put Power
NOTE:
- To avoid damage of products do not connect Transmitter RJ45 PoE Out to a PoE Switch!
- Joining function by hardware is only available between Transmitter/Receiver or
Transeiver devices except camera.

1.7. Network Password Change
All EPoC products have the same network password on factory default to support plug & play between EPoC
products. In case of multiple 1:1 connections, It is possible to avoid network interference by setting password
of each group.
1. Basic connection
-Prepare a short coaxial cable for convenience.
-Connect EPoC products and power adapter.
2. Unjoin : removing the password
-Push the join button for 15 seconds. BNC Join LED turns off.
-Push the join button for 15 seconds on the other side.
3. Join : making new password
-After unjoining, push the join button for 1 or 2 seconds.
PWR LED turns off and on, and then BNC Join LED turns on.
-Push the join button for 3 seconds on the other side.
-After PWR LED is on, BNC Join LED on both side are flickering and the network is working again.
4. Repeat above 1~3 for the other groups.
hNew and random password is automatically assigned and it can not be restored to the factory default
password.
Group A
Group C
Group B
Transmitter
Transmitter
Transmitter
AC/DC Adapter (56V) Receiver
AC/DC Adapter (56V) Receiver
AC/DC Adapter (56V) Receiver
Quick Installation Guide — 6
NOTE:
-To avoid damage of products do not connect Transmitter RJ45 PoE Out to a PoE Switch!
-Joining function by hardware is only available between Transmitter/Receiver or
Transeiver devices except camera.

Quick Installation Guide — 7
1.8. LED Indicators
Indicator Color Function
PoE-ON PoE Output Status (Transmitter model only)
PD-AUX PoE Input Status (Receiver model only)
Data-Link Blinks when transmitting Ethernet data
Join-Link EPoC products connected
Power 56VDC or PoE Input connected
1.9. Specification
Model Transmitter Receiver
Interface
Coax 1 x 75Ω BNC (Female) - Ethernet over Coax (B-LinX)
Ethernet 1 x RJ45 - 10/100 Base-T with Auto-detect MDIX
Transmission Rate 95Mbps Full Duplex
Transmission
Distance
Ethernet up to 2.4Km(RG-6)
PoE (PoC) up to 1.2Km (RG-6 / 7W camera)
LED
Indication
Ethernet 1 x Data-Link (Yellow)
EPoC 1 x Join-Link (Green)
Power 1 x Power On(Amber)
PoE 1 x PoE Out (Red)
Encryption 128-bit AES
Power
Input B-Linx or DC12V~57V PoE Switch or DC12V~57V
PoE Output Extra PoE up to 60W PoE Not Supported
PoC Only
Mechanical
Dimension 82.4(L) x 61.6(W) x 24(H)mm
Weight 77g
Environment
Operating Temp -20 ~ 60°C
Storage Temp -30 ~ 80°C
Relative Humidity 10% ~ 90%
Compliance
Certification FCC, CE, KC, RoHS
Surge Protection IEC 61000-4-5 4kV(1.2 / 50us), 2kA(8 / 20us)
Optional Accessories 56VDC / 1.2A External Power Supply

Quick Installation Guide — 8
1.10. Caution
•Please install the device following the installation guide.
•Do not touch the device and cable with wet hands.
•Keep away from moisture and shock.
•Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that produce
heat.
•Indoor use only.
•Do not use for other purposes. (i. e. Connecting analog camera to BNC connector)
•Do not disassemble or modify this device.
•Do not put any sticker or paint on it.
•If this device is defective or malfunctioning, please unplug the power adapter immediately and contact dealer or
service center.
•Use only rated 56V power adapter specified by the manufacturer. Connect DC power to EPoC Extender first and
then to AC outlet.
1.11. Warranty
•This device has passed the quality control and product inspection.
•Please install and use according to the installation guide.
•The warranty period for this product is 24 months from the date of purchase.
•Any damages or breakage from user’s abuse, accident, modification or natural disasters will not be covered
manufacturer’s warranty.

Pre-field verification — 9
2. Pre-field verification
2.1. Check transmission line
2.1.1. Transmission line type
█ EPoC (Ethernet over Coax) Applicable
Coaxial cable
3C, 5C, 7C, 10C, RG58, RG59,
RG6, RG11, KX6,
KX100, etc.
Ethernet over
Coax Extender
2-Wire
UTP cable
EPoC Extender +
IAM-4MU1001M0A
Other manuals for IAM-6MC1001MTA
1
This manual suits for next models
3
Table of contents
Other Eneo Receiver manuals


















