Emerson Unidrive M400 User manual

Document Part # 026-4176 Rev 1 Page 1 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

The keypad and display gives information about the

operating status of the drive and trip codes. It provides

the ability to change parameters, stopping and starting

the drive, and the ability to perform a drive reset.

Keypad Number Keypad Description

1 (Enter)

The Enter button is used to enter

parameter view or edit mode, or to

accept a parameter edit.

2 (Navigation)

The Navigation keys can be used to

select individual parameters or to edit

parameter values. In keypad mode, the

“Up” and “Down” keys are alsoused to

increase or decrease the motor speed.

3 (Start) The Start key is used to start the drive in

keypad mode.

4 (Stop/Reset)

The Stop / Reset key is used to stop and

reset the drive in keypad mode. It can

also be used to reset the drive in

terminal mode.

5 (Escape)

The Escape key is used to exit from the

parameter edit / view mode or

disregard a parameter edit.

Figure 1 - Unidrive M400

Figure 2 - Unidrive M400 Keypad Details

Supervisory Controller Setup with

M400 VFD Drive

Quick Start Guide

This document will guide you through setting up and

commissioning the M400 VFD Drive in Supervisory

Controllers (E3 and Site Supervisor).

Complete All Programming Before you set up the M400

Drive.

Note that the M400 Drive requires Supervisory Controller

firmware version 2.14F01 and above.

Document Part # 026-4176 Rev 1 Page 2 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 1: Configuring M400 VFD Drive

Note: Do not connect the device communications to E2 controller.

1. Press right/ left arrow key and go to Pr MM.000 then press . Select Reset 60Hz defs then press

Note: Pressing allows you to enter and exit parameter edit mode.

2. Press to return the drive into the No Action display.

3. Go to Pr 00.005 (Drive Config), then press . Select Preset, then press .

4. Set Pr 00.010 (User Security Status), then press . Select All Menus, then press .

5. Set Pr 06.004 (Start/Stop Logic), then press . Select 6, then press .

6. Set Pr 11.023 (Serial Address), then press . Select 2, then press .

7. Set Pr 11.024 (Serial Mode), then press . Select 8 1 NP, then press .

8. Set Pr 11.020 (Serial Reset), then press . Select On to reset communications.

Note: The device will flash to On and returns to Off, press .

9. Set Pr 12.000 (Parameter mm.000), then press . Select Save Parameters, then press .

10.Press to return the drive into the No Action display.

Note: The drive is now ready to communicate with the Supervisory controller and is ready for a test/run.

Model Max # of Instances

1 SR 20

2CXe 16

3CX 16

4BXe 16

5BX 16

6RXe 16

7RX 16

8SMF No

Document Part # 026-4176 Rev 1 Page 3 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 2: Setting the Baud Rate in the Supervisory Controller

Gear icon > Configure System Properties > General System Properties

• Set the Com Port baud to 19.2

Figure 3 - General System Properties Tree Hierarchy

Figure 4 - Set the Baud Rate, Data Size, Parity, and Stop Bits

Document Part # 026-4176 Rev 1 Page 4 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 3: Wiring the M400 VFD Device to Emerson Controllers

Wire the device as shown below:

COM wiring is the REVERSE polarity of Site Supervisor.

•+ On the Com port goes to - on the VFD.

•- On the Com port goes to the + on the VFD.

• Do NOT connect shield to any terminal on the controller or VFD. Connect shield directly to Earth Chassis at the

controller; clip and insulate shield at VFD end of cable.

• If VFD is the last device at the end of Com segment, terminate with 150 ohms between terminals 2 and 3.

Figure 5 - Wire the M400 VFD Device to Site Supervisor

Document Part # 026-4176 Rev 1 Page 5 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

COM wiring is the same polarity as E2 and E3.

•+ On the Com port goes to + on the VFD.

•- On the Com port goes to - on the VFD.

• Do NOT connect shield to any terminal on the controller or VFD. Connect shield directly to Earth Chassis at the

controller; clip and insulate shield at VFD end of cable.

• If VFD is the last device at end of Com segment, terminate with 150 ohms between terminals 2 and 3.

Figure 6 - Wire the M400 VFD Device to E2/E3

Document Part # 026-4176 Rev 1 Page 6 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 7 - Site Supervisor to M400 (MODBUS)

Document Part # 026-4176 Rev 1 Page 7 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 8 - Site Supervisor to M400 (ANALOG 0-10V)

Document Part # 026-4176 Rev 1 Page 8 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 9 - Lumity E3 to M400 (MODBUS)

Document Part # 026-4176 Rev 1 Page 9 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

Figure 10 - Lumity E3 to M400 (ANALOG 0-10V)

Document Part # 026-4176 Rev 1 Page 10 of 16

Visit our website at www.climate.emerson.com for the latest technical documentation and updates.

STEP 4: Adding the Device to the Supervisory Controller

1. From the home page click the control inventory icon to go to the Control Inventory page.

2. From the HVAC drop-down list, select M400 from the list.

STEP 5: Commissioning the Device to the Supervisory Controller

From the Control Inventory screen select the Modbus address for the M400 and click the checkmark

to save and start commissioning. (Best practices tip: set the Modbus number to match the connected

Com Port and the Address to match the M400 addressing in STEP 1).

Drive Setup:

1. Click the M400 to go to the M400 setup page.

2. Go to the General tab.

3. Set CfgSyncAction on the to Write to Device.

4. On the Inputs tab, set DIRECTION to Forward or Reverse. This verifies that the drive should run

correctly.

5. Set RUN to OFF. This verifies that the drive should inhibit.

Figure 11 - Adding M400 and Addressing

Other manuals for Unidrive M400

Table of contents

Other Emerson Controllers manuals

Emerson

Emerson Fisher CS400 Series User manual

Emerson

Emerson Bettis RGS Q Series User manual

Emerson

Emerson Unidrive HS30 User manual

Emerson

Emerson Fisher S202 User manual

Emerson

Emerson Alco Controls FSX Series User manual

Emerson

Emerson 99 User manual

Emerson

Emerson AVENTICS Sentronic D User manual

Emerson

Emerson ET124 Series User manual

Emerson

Emerson Fisher 630 Series User manual

Emerson

Emerson Fisher Y692 User manual

Emerson

Emerson Fisher MR95 Series User manual

Emerson

Emerson FISHER 670 Series User manual

Emerson

Emerson EC3-D72 User manual

Emerson

Emerson Fisher 92S User manual

Emerson

Emerson 289A User manual

Emerson

Emerson Dixell XR10C Operating instructions

Emerson

Emerson CASH A-401 User manual

Emerson

Emerson Fisher Type 99 User manual

Emerson

Emerson PaCSystems VersaMax Series User manual

Emerson

Emerson Tescom ER5000 Series User manual

Emerson

Emerson TARTARINI FL Series User manual

Emerson

Emerson Tarantini MN Quick guide

Emerson

Emerson Fisher 299H User manual

Emerson

Emerson Fisher 1051 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide