Emerson RSTi-EP CPE200 Series User manual

Instructions to printer

DO NOT PRINT THIS PAGE

This document is intended to be printed in

color

as a

5.5 (width) x 6.5 inch (length) booklet with stapled binding.

Use high-quality, glossy 20lb (75 g/m²) paper.

Print double-sided. Fold sheet of 8.5” x 11” in two, trim

length, and staple spine.

The European version can use A4 in place of 8.5” x 11”.

RSTi-EP CPE200 Series Controllers

Quick Start Guide

GFK-3109B

Dec 2022

 
 
i RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B 
Contents 
Contents .............................................................................................. i 
Initial Checks ......................................................................................1
Front Panel Description .....................................................................2
Displays and LED Indicators ........................................................................... 4 
Ethernet Port LEDs........................................................................................... 5 
Front Display LEDs ........................................................................................... 6 
RUN/STOP Switch............................................................................................. 8 
Connectors and Ports ...................................................................................... 8 
DIN Rail Installation.........................................................................15 
Thermal Requirements ....................................................................20 
Controller Start-up ...........................................................................21 
Required Components .................................................................................. 21 
Basic Installation Steps.................................................................................. 22 
LED Behavior During Startup ....................................................................... 23 
Installation in Hazardous Areas .....................................................24 
Network Configuration .............................................................................. 24 
Update Firmware Webpage Password........................................................ 29 
Reset to Factory Defaults .............................................................................. 30 
Removable Data Storage Device (RDSD)..................................................... 31 
Periodic Maintenance.................................................................................... 32 
Additional Information....................................................................33 
General Contact Information ....................................................................... 35 

1 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

Initial Checks

Upon receiving your equipment, carefully inspect all shipping

containers for damage. If any part of the system is damaged, notify

the carrier immediately. The damaged shipping container should be

saved as evidence for inspection by the carrier.

As the consignee, it is your responsibility to register a claim with the

carrier for damage incurred during shipment. Emerson will fully

cooperate with you, however, should such action be necessary.

After unpacking the equipment, record all serial numbers. Serial

numbers are required if you should need to contact Customer Care

during the warranty period. All shipping containers and all packing

material should be saved should it be necessary to transport or ship

any part of the system.

Verify that all components of the system have been received and

that they agree with your order. If the system received does not

agree with your order, contact Customer Care.

2 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

Front Panel Description

Figure 1: Front Panel View of EPXCPE205

3 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

Figure 2: Front Panel View of EPXCPE210/215/220/240

4 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

Displays and LED Indicators

Label

Function

Description/Notes

LED

Multi-function PLC LED.

RUN

LED

Multi-function PLC LED.

REM IO

LED

Remote IO state LED. PLC LED that will indicate

whether ALL or SOME PROFINET devices are

connected.

FORCE

LED

PLC LED that indicates a “forced” value is present in

User Logic.

FLT/RDSD

LED

PLC LED that will indicate a STOP-FAULT condition,

IP Conflict Detected, and also the RDSD state.

DUAL LAN

LED

PLC LED that indicates EPXCPE205 LAN mode

configuration. This LED is not labeled on any other

EPXCPE model.

RUN EN

RUN/STOP Switch

PLC in Run Outputs Enabled.

RUN DIS

RUN/STOP Switch

PLC in Run Outputs Disabled.

STOP

RUN/STOP Switch

PLC in Stop.

PHY PRES

RDSD

Physical

Presence/RDSD

Button for Physical Presence actions (i.e. password

change), RDSD and reset to factory defaults.

RDSD –Single press to perform an upload.

RDSD –Double press to perform a download.

Is used to initiate Reset to Factory Default Settings.

µSD

Micro SD card

Port for the micro SD card.

RS232

Serial Port

Port for serial communications. Only support RS-

232.

USB

RDSD

USB 2.0/RDSD

USB connection for RDSD, and potentially other

features in the future.

PORT X

Ethernet Port

Ethernet Ports. X = 1, 2, 3, or 4.

LNK

Ethernet Port LED

LED that indicates Ethernet Link and Speed. Belongs

to the Ethernet Connector.

ACT

Ethernet Port LED

LED that indicates Ethernet activity on the link.

Belongs to the Ethernet Connector.

5 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

Ethernet Port LEDs

•The Ethernet Port LEDs are located in the PHY connector

itself. They are controlled by the PHY

•There are two LEDs per port, one for Link/Speed (“LNK”)

and one for Activity (“ACT”)

•Ethernet LinkSpeed (“LNK”):

oGREEN indicates 1 Gbps

oAMBER indicates 100 Mbps

oOFF indicates 10 Mbps (currently not supported

per spec)

•Ethernet Activity (“ACT”):

oGREEN indicates Link

oBLINKING GREEN indicates activity on the link

Figure 2: 3-Position Switch RUN EN/RUN DIS/STOP

6 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

Front Display LEDs

LED Label

LED State

Operating State

Green (steady)

Powered up, the controller is

up and ready.

Amber (steady)

Thermal warning –a warm

condition

Red (steady)

Thermal shutdown

- hot temperature condition

RUN

Green (flashing in

unison)

Reset to factory defaults

RUN

REM IO

Green (flashing in

unison)

Programmable parts update

RUN

Green (steady)

The controller is running with

I/O outputs enabled

Green (flashing)

Fatal error blink code during

power up

Amber (steady)

The controller is running with

I/O outputs disabled

REM IO

Green (steady)

All PROFINET devices

connected

Green (flashing)

Unit is starting up (see LED

power-up sequence)

Amber (steady)

Some PROFINET devices

connected

FORCE

Amber (steady)

The controller has a

forced value(s)

7 RSTi-EP CPE200 Series Controllers Quick Start Guide GFK-3109B

LED Label

LED State

Operating State

FLT/RDSD

Green (steady)

USB device present and RDSD is

ready

Green (steady)

RDSD Operation completed

successfully

Green (flashing)

RDSD download operation in

progress

Amber (flashing)

RDSD upload operation in

progress

Red (steady)

The controller is in a Stop-

Fault state

Red (flashing)

RDSD has failed

Red (flashing)

If RDSD is not being performed,

indicates IP conflict detected

DUAL LAN

(EPXCPE205

only)

Green (steady)

Dual LAN operating mode

Off

Single LAN operating mode

This manual suits for next models

Table of contents

Other Emerson Controllers manuals

Emerson

Emerson Dixell IEV12D Wiring diagram

Emerson

Emerson EC20 Series User manual

Emerson

Emerson Fisher 785C User manual

Emerson

Emerson Fisher 2052 User manual

Emerson

Emerson AMPGARD RVSS User manual

Emerson

Emerson E2 User manual

Emerson

Emerson E2 Enhanced RX Service manual

Emerson

Emerson ROC809 User manual

Emerson

Emerson Fisher 1052 User manual

Emerson

Emerson AW Series User manual

Emerson

Emerson TESCOM WegaMed Compact Series User manual

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS User manual

Emerson

Emerson TESCOM Setup guide

Emerson

Emerson BETTIS E796 2000 M2CP User manual

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS User manual

Emerson

Emerson Bettis CBA*30-SR series Operating instructions

Emerson

Emerson Fisher L2e User manual

Emerson

Emerson EC2-742 User manual

Emerson

Emerson PACSystems RX3i Energy Pack User manual

Emerson

Emerson dixell XR03CX Wiring diagram

Emerson

Emerson MultiFlex RTU User manual

Emerson

Emerson E2 User manual

Emerson

Emerson Bristol CI-9110 User manual

Emerson

Emerson Control Link ACC Service manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide