Emerson Lumity E3 User manual
Document Part # 026-4167 Rev 1 Page 1 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
The E3 (P/N 860-1300) is a system that combines energy management
with the ability to monitor various facility systems and provide alerts
when there are issues that need attention. This system provides HVAC
control, Refrigeration System Monitoring and Control, as well as
Lighting Control. In addition, the E3 can monitor and report energy
consumption and take action to reduce the energy demand during peak
periods. This can have a direct impact on utility bills by reducing total
energy costs. E3 ensures that the HVAC and lighting systems are on and
off at the appropriate times. This ability to monitor store conditions can
potentially minimize energy consumption.
Technical Specifications
*Operating Temperature -40°F to 113°F (-40°C to 45°C)
*Tested to UL60730-1 standard
Operating Humidity
Storage Humidity 5% - 95% RH non-condensing at 90°F
5% - 100% RH
24 VAC 24 VAC ±20%, 50/60 Hz, Class 2
Dimensions 12” L x 12.5” W x 3.75 H”
4 RS485 ports COM 1 = RS485-COM2A and RS485-COM2B
COM 2 = RS485-COM6<ISOLATED>
COM 3 = <ISOLATED>RS485
COM 4 = RS485-COM4A and RS485-COM4B
2 Ethernet ports ETH 0, ETH 1
2 USB ports J2, J3
External Pollution Rating All Models: Pollution Degree 3
Rated Impulse Voltage 2500/4000V
Lithium Battery Marking Caution: The cell used in this device may present a fire or chemical burn hazard if mistreated.
Do not disassemble, heat above 212°F (100°C), or incinerate.
Figure 1 - E3 Controller
Quick Setup Guide
LumityTM E3 Supervisory
Control
Document Part # 026-4167 Rev 1 Page 2 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
Wiring
1. Connect the RS485 Communication wire to the terminal block headers as shown. The Cables are numbered
1 through 4.
2. Connect the 2-pin 7.5mm power connector and Ground wire as shown in Figure 2.
3. Connect the other end of the power cable to one of the 50VA P/N 640-0040 transformers.
4. Plug the 50VA P/N 640-0040 Transformers into a 120VAC outlet.
5. Turn the power switch ON (up position). The unit should boot up to the home screen.
6. You can log into the unit the first time by using the below username and password if needed.
• Username = user
• Password = pass
7. Once logged in you will be prompted to change your password.
Figure 2 - PIB Board Layout
Document Part # 026-4167 Rev 1 Page 3 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
Ethernet Connections
•ETH 0 is used to connect to corporate LAN.
•ETH 1 is designed to be used for directly connecting to PIB, and laptop or
PC and network devices. The default IP for ETH 1 is 192.168.1.250.
E3 RS485 Wiring Guide Example
• For E3 Serial IO Net connections, connect the white wire to the positive
terminal and the black wire to the negative terminal.
• For 8RO and MultiFlex RS485 IO Net connections, connect the white
wire to the positive terminal and the black wire to the negative terminal.
• Connect the shield wire to earth/chassis at the end of the IO Net
(network) segment. Connect the shield wire to the center terminal (0V)
of the IO Net connector on the E3.
• For daisy-chain configurations, terminate devices at the beginning and
the end of the network segment. All other devices in the network
segment are not terminated (termination jumpers in the not-terminated
position).
Figure 4 - E3, MultiFlex, and 8RO Wiring Layout
Figure 3 - ETH Ports
Document Part # 026-4167 Rev 1 Page 4 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
Direct Connect Instructions - Connect your laptop to E3’s Ethernet port ETH 1
All configuration can be accomplished through the E3’s built-in display or through a laptop, PC, or tablet. On your PC:
1. Under Control Panel - Network and Sharing Center, select Change adapter settings.
2. Select the Local Area Connection port being used.
3. Select Properties.
Figure 5 - E3 and XR75 Wiring
Document Part # 026-4167 Rev 1 Page 5 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
4. Highlight the section Internet Protocol Version 4 (TCP/IPv4) and click Properties:
Figure 6 - Change Adapter Settings
Figure 7 - Highlight Internet Protocol Version 4 (TCP/IPv4)
Document Part # 026-4167 Rev 1 Page 6 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
5. Click Use the following IP address: and enter the IP address 192.168.1.251 and the Subnet mask 255.255.255.0 of the PC
being used on the Local Area Network or direct connection and click OK:
Logging Into the E3 Controller
1. Launch a preferred Web browser: Chrome (preferred), IE 11 and above, Firefox 13 and above, and Safari (all versions) are
the supported browsers.
2. Enter the IP Address of the device.
3. Enter your Username/Password (default user/pass) and click Login. Then update your password to the minimum
complexity requirements and click Save.
Note that when directly connecting your laptop or PC to ETH 1, enter the default IP into the browser address bar: ETH 1
Default IP Address is 192.168.1.250.
Figure 8 - IP Address and Subnet Mask
Figure 9 - Login Screen at Controller Startup and Update Password
Document Part # 026-4167 Rev 1 Page 7 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
How to Change the IP Address
Method 1: Direct Connect
1. Select the Main Menu icon > Configure System > General System Properties > Network Settings:
2. On the INTERNET (TCP/IP) section on the screen, enter the IP Address in the ETH 0 IP Address field.
Note that you can set up the Peer Group, Unit Number, Network Mask, and Default Gateway on this screen.
Method 2: USB Port
1. Create a “network.txt” with your desired settings (Figure 10):
2. Save to the root folder of a thumb drive. Insert the thumb drive into the USB port of E3.
3. Power cycle the E3. The new IP Address will be saved.
Figure 10 - Enter IP Address in the ETH 0 IP Address Field
Figure 11 - Network.txt Notepad
Document Part # 026-4167 Rev 1 Page 8 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
Setup Wizard
Note that if setpoints have been pre-loaded in the unit, the Setup Wizard will not auto-start after logging in.
If your unit has been received directly from the Emerson factory, the Setup Wizard will open and take you through the
following setup screens:
Localization Screen
Set the E3’s localization data such as language, date and time formats, and engineering units from the Localization screen.
Language: The default for the language selection is American English (United States). The system stores a setting for the
preferred system language (internal language code). The default language is used when no user is currently logged into the E3
or when the currently active preferred language does not have a translation for a given label, prompt, or display text.
Date: The Date format can be set to either Day, Month, and full Year (D-M-YR) or Month-Day and full Year (M-D-YR) format.
The day, month, and year values are separated by either a forward slash or a dash line depending on user selection.
The Date Format can be changed based on user preference and saved to user profiles. On initial E3 startup, the Date format
defaults to the format of the language selected. For example, en-US will default to D-M-YR and all others will default to M-D-YR.
Time: The Time format can be set to either a 12-hour (12-hr) format or 24-hour (24-hr) format. The hour, minute, and second
values are separated by either a colon or a period depending on user selection.
The Time format can be changed based on user preference and saved to user profiles. On initial E3 startup, the Time format
defaults to the format of the language selected.
Date and Time delimiters default to forward slashes and colons.
Engineering Units: The default engineering units are based on the assigned units for the chosen preferred language. Users can
choose or change their preferred set of engineering units and save them to their user profiles.
The default engineering units are based on the International System of Units (SI System) format.
Set the system language type in the Language drop-down menu. Click the right arrow > to save and proceed to the System
Values screen.
Figure 12 - Localization Screen
Document Part # 026-4167 Rev 1 Page 9 of 10
©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
System Values Screen
From the System Values screen, name the unit by entering it in the Site Name field. The Confirmation window will slide open.
Click OK. Then click the right arrow > to proceed to the Network Settings Screen.
Figure 13 - System Values Screen
This document may be photocopied for personal use.
Visit our website at http://www.climate.emerson.com/ for the latest technical documentation and updates.
Join Emerson Technical Support on Facebook. http://on.fb.me/WUQRnt
For Technical Support call 833-409-7505 or email ColdCh[email protected]
The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied,
regarding the products or services described herein or their use or applicability. Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”),
reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does not assume responsibility for the selection, use or maintenance of any product.
Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.
Document Part # 026-4167 Rev 1 Page 10 of 10
Network Settings Screen
Configure the settings on the Internet TCP/IP screen such as host name, text, and email settings. If you have Internet access,
enter the IP Subnet Mask and Default Gateway settings (see your IT Administrator). If connecting directly to a laptop, use the
Default IP and leave the DHCP set to Disable. For text messaging, enable the SMS setting and use the SMTP address (see your IT
Administrator).Click the arrow > to save and finish the Setup Wizard.
For more product information, scan the QR code:
Figure 14 - Network Settings
This manual suits for next models
1
Table of contents
Other Emerson Controllers manuals
Emerson
Emerson Control Link ACC Service manual
Emerson
Emerson EC2-712 User manual
Emerson
Emerson Fisher L2e Configuration guide
Emerson
Emerson dixell WING XW260L Wiring diagram
Emerson
Emerson E2 User manual
Emerson
Emerson Fisher 656 User manual
Emerson
Emerson Bettis BHH Series User manual
Emerson
Emerson Bettis CBA*30-SR series Operating instructions
Emerson
Emerson 289A User manual
Emerson
Emerson PACSystems RX3i User manual
Emerson
Emerson Bettis M Series User manual
Emerson
Emerson DL8000 Quick guide
Emerson
Emerson Y696 User manual
Emerson
Emerson Tescom 44-1800 Series User manual
Emerson
Emerson EIM 2000 Series User manual
Emerson
Emerson FISHER FIELDVUE DLC3010 User manual
Emerson
Emerson Fisher 670 Series User manual
Emerson
Emerson Branson 2000X ae User manual
Emerson
Emerson FISHER T205B User manual
Emerson
Emerson Fisher 61 Series User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
Airflow
Airflow Uno hab Installation and operating instructions
ABB
ABB ACS580-01 drives Hardware manual
Panasonic
Panasonic GM1 Series Reference manual
AutoAqua
AutoAqua Smart ATO micro SATO-120P manual
Panasonic
Panasonic FP? Positioning Unit RTEX Technical manual
Samson
Samson Type 5824 Mounting and operating instructions
