Emerson EIM TEC2 500 User manual

Quick-Start Guide

E2K-210-05-18 Rev. 3

September 2018

EIM TEC2 Electric Actuator with

Model 500 Quick-Start Guide

(Model 500 Discontinued)

Welcome to TEC2

September 2018

Quick-Start Guide

E2K-210-05-18 Rev. 3

1Welcome to TEC2

Welcome to TEC2

The TEC2 actuator’s Local Display Module (LDM) and Remote Display Module (RDM) provide easy-to-read

actuator information.

The screen graphics will display the mode of operation, valve status, position, torque, and alarm symbols.

The message center will display actuator setup options, data entry feedback, and alarm messages.

Once you follow the simple steps outlined in this guide, the actuator will be ready for normal operation.

The bar graph, position digits, icons, and LEDs will indicate the valve status.

LED Indicators

Valve Torque

Display Diagnostic

Operating

Mode

Moving Status

Welcome to TEC2 Quick-Start Guide

E2K-210-05-18 Rev. 3

September 2018

2Welcome to TEC2

Factory Settings

The actuator has been congured as specied in the order. No further changes should be necessary other than

setting the position limits, and, if network controlled, setting a unique network address. If full data was not

provided when ordering or if changes are needed, see the TEC2 Installation & Operation Manual

(E2K-420-0117), which can be found at www.emerson/eim.

Power Actuator

Verify the voltage rating on the unit nameplate. Connect power to the unit.

Are Position Limits Set?

Does “SET LIMITS BEFORE OPERATING,” “EE%,” and the alarm icon appear, and is the yellow LED

blinking? If so, then position limits have not been set.

Setting Valve Position Limits Initially

September 2018

Quick-Start Guide

E2K-210-05-18 Rev. 3

3Setting Valve Position Limits Initially

Setting Valve Position Limits Initially

2 3 4

YES LOCAL

YES,

NO,

YES,

Release

quickly.

STOP

Place the selector knob in the STOP position. Then toggle the control knob in rapid succession to YES, then

NO, then YES, then NO and release. The Setup icon will be displayed on the display module and “SETUP?” will

be displayed on the message center. Rotate the control knob to “YES.” The message center will display “SET

LIMITS BEFORE OPERATING.” Set position limits as described on the next pages.

Setting Position Limits for Electrical Operation Quick-Start Guide

E2K-210-05-18 Rev. 3

September 2018

4Setting Position Limits for Electrical Operation

Setting Position Limits for Electrical Operation

STEP 1: CLOSED Valve Position

234

YES

LOCAL CLOSE

Hold until

desired

position is

reached.

STOP

Turn the selector knob to the “LOCAL” position. Hold the control knob in the “CLOSE” position until desired

position is reached. Dis-engage motor drive by setting the declutch lever in “HAND” mode.

Using handwheel, move the valve in the open direction for one handwheel turn to allow for motor coasting.

Re-engage motor drive by setting the declutch lever out of “HAND” mode.

Return the selector knob to the “STOP” position. Select “YES” to set new close limit.

Setting Position Limits for Electrical Operation

September 2018

Quick-Start Guide

E2K-210-05-18 Rev. 3

5Setting Position Limits for Electrical Operation

Setting Position Limits for Electrical Operation

STEP 2: OPEN Valve Position

Turn the selector knob to the “LOCAL” position. Hold the control knob in the “OPEN” position until

desired position is reached. Dis-engage motor drive by setting the declutch lever in “HAND” mode. Using

handwheel, move the valve in the close direction for one handwheel turn to allow for motor coasting. Re-

engage motor drive by setting the declutch lever out of “HAND” mode.

Return the selector knob to the “STOP” position. Select “YES” to set new open limit.

234

YES

LOCAL OPEN

Hold until

desired

position is

reached.

STOP

Setting Position Limits for Manual Operation Quick-Start Guide

E2K-210-05-18 Rev. 3

September 2018

6Setting Position Limits for Manual Operation

Setting Position Limits for Manual Operation

STEP 1: CLOSED Valve Position

Turn the selector knob to the LOCAL position. At the “CLOSE VALVE THEN SELECT STOP” prompt, depress the

declutch lever while rotating the handwheel until the clutch is fully engaged. Release the lever.

When the valve is fully closed. Return the selector knob to the STOP position.

At the “ACCEPT CLOSE LIMIT” prompt, select “YES.”

Advance to the “SAVE CHANGES?” prompt and answer YES to save the changes.

2 3 4

YES

LOCAL

STOP

Depress

declutch,

rotate

handwheel

until...

declutch is fully

engaged.

Release

declutch,

Setting Position Limits for Manual Operation

September 2018

Quick-Start Guide

E2K-210-05-18 Rev. 3

7Setting Position Limits for Manual Operation

Setting Position Limits for Manual Operation

STEP 2: OPEN Valve Position

Turn the selector knob to the LOCAL position. At the “OPEN VALVE THEN SELECT STOP” prompt, depress the

declutch lever while rotating the handwheel until the clutch is fully engaged. Release the lever.

When the valve is fully opened. Return the selector knob to the STOP position.

At the “SAVE LIMITS” prompt, select “YES.”

Advance to the “SAVE CHANGES?” prompt and answer YES to save the changes.

2 3 4

YES

LOCAL

STOP

Depress

declutch,

rotate

handwheel

until...

declutch is fully

engaged.

Release

declutch,

Check the Open/Closed Settings Quick-Start Guide

E2K-210-05-18 Rev. 3

September 2018

8Check the Open/Closed Settings

Check the Open/Closed Settings

Valve Closed

As you operate the valve in the close direction, verify

that the green LED is blinking. When fully closed is

reached, verify that the green LED stays ON and 0%

is displayed.

1When turning to close,

green LED blinks.

2When fully closed,

green LED remains lit.

Valve Open

As you operate the valve in the open direction, verify

that the red LED is blinking. When fully open is

reached, verify that the red LED stays ON and 100%

is displayed.

1When turning to

open, red LED blinks.

2When fully open,

red LED remains lit.

Note

It is also congurable to have a red LED for

Valve Closed.

Note

It is also congurable to have a green LED for

Valve Open.

Table of contents

Other Emerson Controllers manuals

Emerson

Emerson Fisher 61 Series User manual

Emerson

Emerson Dixell XRB60CHC Wiring diagram

Emerson

Emerson Fisher MR95 Series User manual

Emerson

Emerson Dixell XRi30T Wiring diagram

Emerson

Emerson YARWAY Series Operation and maintenance manual

Emerson

Emerson ET124 Series User manual

Emerson

Emerson Tartarini PRX Series User manual

Emerson

Emerson CBA730 Installation instructions

Emerson

Emerson iPro.Genius Quick start guide

Emerson

Emerson Fisher 1098-EGR User manual

Emerson

Emerson Fisher L2e User manual

Emerson

Emerson Dixell XF330M Wiring diagram

Emerson

Emerson Bettis D Series Instruction manual

Emerson

Emerson A36 Manual

Emerson

Emerson Unidrive M400 User manual

Emerson

Emerson White-Rodgers 21M51U-843 User manual

Emerson

Emerson SP User manual

Emerson

Emerson MR98 Series User manual

Emerson

Emerson Fisher S202 User manual

Emerson

Emerson Leroy Somer R450 Instruction Manual

Emerson

Emerson 818-9010 User manual

Emerson

Emerson PeC C100 User manual

Emerson

Emerson EC1-233 User manual

Emerson

Emerson fisher 1008 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide