Emerson Bettis SCE300 User manual

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

July 2020

Bettis SCE300

Logic Board Firmware Upgrade Programmer ICD-U64 Procedure

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Notes

July 2020

This page intentionally left blank

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Table of Contents

July 2020

Table of Contents

Section 1: Firmware Upgrade

1.1 Tools ............................................................................................................. 1

1.2 ICD-U64 Programmer Preparation ................................................................ 3

1.3 Firmware Update .......................................................................................... 4

1.4 Firmware Upload........................................................................................... 4

1.5 Actuator Settings Checklist ......................................................................... 16

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Notes

July 2020

This page intentionally left blank

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade 1

Section 1: Firmware Upgrade

This procedure details how to program rmware on the logic board for the Bettis SCE300

electric actuator using the ICD-U64 Programmer.

1.1 Tools

! WARNING

Installation, conguration, commissioning, maintenance, and repairs must be performed

by approved and qualied personnel only.

NOTICE

Certain nameplates may carry more than one approval, and each approval may have

unique installation/wiring requirements and/or conditions of "safe use", installation, and

maintenance. These special instructions are in addition to and may override the standard

installation procedures. Special instructions are listed by approval type.

To update the rmware of the SCE300 actuators, the following tools are necessary:

• PC with program CSSLOAD-CCS Programmer Control Software installed

(Figure 1). This software can be downloaded from:

http://www.ccsinfo.com/content.php?page=ccsloadsw

• PC with USB Drivers for all CSS programmers/debuggers

• Firmware “F02_63_125_v3_11.X.production”, for models E006, E013 or

latest revision

• Firmware “F02_250_500_v4_12.X.production”, for models E025, E051, E091,

E171 or latest revision

• The Universal programmer ICD-U64 (Figure 2)

• Logic Board or Actuator

• Cable from the ICD-U64 to the processor card rmware programming connector

part number: VA001-692-15

Figure 1

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade2

Section 1: Firmware Upgrade

Figure 2 ICD-U64 CCS Programmer

ICD-U64 USB Cable to PC

ICD-U64 USB Programmer

Coonector (Logic Board Side)

Figure 3 SCE300 Logic Board

Actuator size:

250/E025

500/E051

1000/E091

2000/E171

Programming

connector

Actuator size:

063/E006

125/E013

Table 1. Programming Connector Pinout

Signal ICD-U64 Pinout SCE300 Logic Board J15

Real Time Debugging Pin 1

ICSP Clock Pin 2 Pin 5

ICSP Data Pin 3 Pin 4

GND Ground Pin 4 Pin 3

VDD Power Pin 5 Pin 2

MCLR Pin 6 Pin 1

Large Logic Board Small Logic Board

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade 3

Section 1: Firmware Upgrade

1.2 ICD-U64 Programmer Preparation

The ICD-U64 Programmer has an internal jumper to select multiple options to power the

target board (actuator logic board).

1. ICD-U64 programmer internal jumper selecting 5 V

This conguration allows the ICD-64 Programmer to provide power to the logic board.

This conguration can be used to program the logic board as standalone board or to

program the logic board while installed in the actuator. The rmware upgrade of the logic

board should be successful regardless if the logic board is powered from the actuator

power supply or ICD-U64 programmer.

Jumper select +5 V

2. ICD-U64 no jumper

The ICD-U64 internal jumper is not present or was set to no power the target board. It's

not possible to upgrade rmware in the logic board as a standalone board since no power

is being supplied to the target board. If the logic board is installed in the actuator, the

actuator requires to be powered on to have a successful rmware upgrade. Note that a

new programming tool will likely have this no voltage setting.

No jumper, or jumper selecting middle pin only

3. ICD-U64 programmer internal jumper selecting 3.3 V

This option must not be selected, it is not applicable for the SCE300 actuator.

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade4

Section 1: Firmware Upgrade

1.3 Firmware Update

After downloading the new rmware, the actuator settings will return to their default

values. As such, the settings in place prior to the rmware download will need to be set

again. For this reason, be sure to store the actuator settings (e.g. opening speed, closing

speed, % opening torque, % closing torque). Refer to Section 6.2 (Local Conguration of

the SCE300) in the actuator IOM for details. To be clear, all settings will be returned to the

factory default values, it is necessary to reset the open/close travel limits; also, the motor

will default to the smallest size.

If not correctly reset the unit will alarm in open torque.

OM1 settings are not required to be reset because they are unaffected by the processor

card rmware ash.

1.4 Firmware Upload

This procedure is based on the CCS Inc. CCSLOAD ICD-U64 programming tool- This tool can

power the microprocessor from the USB port of the PC, using the 5 V setting and also from

the actuator, using the actuators power source. The microprocessor to be ashed is referred

to as the “target”. Take care that the target is only powered from one source, not both.

In some eld installations is difcult to remove power from the actuator, this procedure

provides instructions in how to download rmware without removing the power from the

actuator, therefore instructions in the procedure must be followed to avoid any damage to

the actuator or any personal injury.

1. It is necessary to identify the position of the jumper inside the ICD-U64

programmer before downloading rmware as indicated in step 1.2.

2. To program the logic board as standalone board, connect the ICD-U64

programmer as shown in the picture and proceed in step 9.

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade 5

Section 1: Firmware Upgrade

3. To program the logic board as part of an actuator with no OM1 board present,

carefully connect the ICD-U64 programmer as shown in the pictures and proceed

in step 9.

Figure 4

4. To program the logic board as part of an actuator with an OM1 board present,

and the actuator is powered ON.

! CAUTION

Accessing the electronics compartment while the actuator is in service exposes the

technician to lethal voltage and possibly from more than one source.

Set the OM1 switch SW4 in ON position, it will prevent the actuator from stroking during

rmware download, and it will allow to maintain the actuator in the last position requested

by the 4 - 20 mA or the 0-10 V loop control.

Switch SW4 in

ON position

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade6

Section 1: Firmware Upgrade

5. Note the position then remove the yellow position indicator to allow the OM1

board to be slightly moved to the side and have access to the programming

connector found in the actuator logic board.

6. Carefully remove the 4 screws that are holding the OM1 board. If the actuator is in

vertical position, there is a risk of dropping the screws inside the actuator. Dropping

the screws inside the actuator could cause a short circuit if the screws drop in the

power board, or a damage of the gears if the screws drop in the gears section.

OM1 board

screws

Other manuals for Bettis SCE300

Table of contents

Other Emerson Controllers manuals

Emerson

Emerson Asco Advantage Series User manual

Emerson

Emerson Dixell iPro Master IPM500D Wiring diagram

Emerson

Emerson Fisher 3024S User manual

Emerson

Emerson Asco 642 Series User manual

Emerson

Emerson Fisher T205 User manual

Emerson

Emerson Bettis Q series User manual

Emerson

Emerson Dixell iChill IC200D EVO Series Wiring diagram

Emerson

Emerson EC3-932 User manual

Emerson

Emerson AVENTICS Sentronic TWIN 615 User manual

Emerson

Emerson Fisher 1190 User manual

Emerson

Emerson SW81 User manual

Emerson

Emerson Tescom 44-6800 Series Installation and operating instructions

Emerson

Emerson Dixell XR03CH Wiring diagram

Emerson

Emerson Unidrive M700 User manual

Emerson

Emerson Dixell XR20CH Wiring diagram

Emerson

Emerson Fisher 133H User manual

Emerson

Emerson XEV EX48 User manual

Emerson

Emerson Dixell XM670K Wiring diagram

Emerson

Emerson DIXELL XR60T User manual

Emerson

Emerson Dixell XR44CX Wiring diagram

Emerson

Emerson Asco Sentronic LP 617 Series User manual

Emerson

Emerson OPM4001 User manual

Emerson

Emerson Dixell XR10C Operating instructions

Emerson

Emerson Dixell XM670K Wiring diagram

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide