Emerson E2 User manual

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 1 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

This document will guide you through setting up and commissioning the High Pressure CO2 controller

(P/N 818-9010) in the E2 controller.

STEP 1: Wiring and Setting the Address of the High Pressure CO2

1. When wiring the RS485 polarity from E2 to the High Pressure CO2 controller:

• Verify that the (+) RS485 side of the High Pressure CO2 line is connected to the (-) side of E2 RS485.

• The (-) RS485 side of the High Pressure CO2 line must be connected to the (+) side of the E2 RS485.

2. To set the address on the High Pressure CO2, press the T1, T3, and T8 buttons on the Main Menu

screen to enter the Configuration screen on the Visograph.

Figure 1 - Main Menu

E2 Setup with the High Pressure CO2

Controller for 527-0396

Quick Start Guide

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 2 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

3. After entering the Configuration screen, the screen below appears.

4. Highlight General Config and press T4 (ENTER).

Figure 2 - Configuration Screen

Figure 3 - General Config Screen

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 3 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

5. After pressing T4 (ENTER) the screen below appears. Press T8 (right arrow) to move to the next

screen.

6. Verify if the address is defaulted at 1. If you need to change the default address, press T5 (down

arrow) and highlight the MODBUS address number. Once the address number is highlighted, press T4

(SET), and the number should blink. Press T3 to increase the address number or T4 to decrease the

address number. After the address number is selected, press T4 (SET) to exit, then press T1 (EXIT)

twice to exit the Configuration mode. If the address is changed, the High Pressure CO2 needs a

manual reboot for the new address to take place.

Figure 4 - General Config Screen

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 4 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

STEP 2: Uploading the Description File to the E2 Controller

1. From UltraSite, connect to your E2 controller (description file # 527-0396).

2. Right-click on the E2 icon and select Description File Upload.

3. Browse to the location of the description file and click Upload.

4. Once the upload is complete, reboot the E2 controller.

Figure 5 - E2 Description File Upload

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 5 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

STEP 3: Adding the Device to the E2 Controller

1. Press , (System Configuration), (Network Setup), (Connected I/O Boards & Controllers).

2. Press (NEXT TAB) to shift over to the C4: Third Party tab. The name of the device will display in

the list. Highlight the device name, then enter the number of devices and press to save

changes.

Figure 6 - Adding the High Pressure CO2

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 6 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

STEP 4: Assigning the MODBUS Port

1. Press , (System Configuration), (Remote Communications), (TCP/IP Setup).

2. Press (NEXT TAB) to shift over to the C3: Serial tab.

Figure 7 - Assigning a MODBUS Port to the Device

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 7 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

3. Select the COM port the device is connected to, press (LOOK UP) and select the appropriate

MODBUS selection.

4. Set the Baud Rate for the chosen port. Press to look up the appropriate speed.

Figure 8 - MODBUS Port Selection

Figure 9 - Baud Rate Selection

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 8 of 9

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

STEP 5: Commissioning the Device into the E2 Controller

1. Press , (System Configuration), (Network Setup), (Network Summary).

2. On the Network Summary screen, highlight the device name, press (COMMISSION). Select the

preferred MODBUS port where you will assign the device, then assign the MODBUS address of the

device.

Figure 10 - MODBUS Device Address Selection

This document may be photocopied for personal use.

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

Join Emerson Retail Solutions Technical Support on Facebook. http://on.fb.me/WUQRnt

The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or

applicability. Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does

not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.

Document Part # 026-4953 Rev 0 07-NOV-2014 Page 9 of 9

3. Once the device is addressed and wired properly, the device should appear online.

Figure 11 - Physical Device Address

Other manuals for E2

This manual suits for next models

Other Emerson Controllers manuals

Emerson

Emerson ET124 Series User manual

Emerson

Emerson Spence T61 Series User manual

Emerson

Emerson Fisher EZH Series User manual

Emerson

Emerson Bettis G10 Series Operating instructions

Emerson

Emerson Fisher EZR series User manual

Emerson

Emerson Bettis CBB Series Installation instructions

Emerson

Emerson Fisher 67D Series User manual

Emerson

Emerson Fisher 67DFSR User manual

Emerson

Emerson KEYSTONE OM13 EPI-2 User manual

Emerson

Emerson Fisher 310A-32A-32A User manual

Emerson

Emerson Fisher Level-Trol 2502 Series User manual

Emerson

Emerson DIXELL XR30CHC Wiring diagram

Emerson

Emerson XM678D Specification sheet

Emerson

Emerson EL-O-MATIC EL35 User manual

Emerson

Emerson Fisher Y696 User manual

Emerson

Emerson Bettis 500 User manual

Emerson

Emerson FISHER 627W User manual

Emerson

Emerson Bettis XTE3000 User manual

Emerson

Emerson PACSafe User manual

Emerson

Emerson TARTARINI FL Series User manual

Emerson

Emerson Fisher R622 User manual

Emerson

Emerson digitax st series User manual

Emerson

Emerson Yarway Integral Strainerimpulse 400 Series Operation and maintenance manual

Emerson

Emerson Fisher 630 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide