Emerson Dixell XC645D Wiring diagram

XC645D

(v. 3.4)

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 2/50

INDEX

1. BEFORE PROCEEDING 4

1.1 CHECK THE SW REL.OF THE XC645D 4

2. GENERAL WARNING 4

2.1 PLEASE READ BEFORE USING THIS MANUAL 4

2.2 SAFETY PRECAUTIONS 4

3. GENERAL DESCRIPTION 5

4. COMPONENTS RELATED TO THE XC645D 5

4.1 PP07, PP11, PP30 PP50: 4÷20MAPRESSURE TRANSDUCERS5

4.2 NP4-67: PIPE MOUNTING TEMPERATURE PROBE 5

5. WIRING & ELECTRICAL CONNECTIONS 6

5.1 GENERAL WARNINGS 6

5.2 WIRING CONNECTIONS 6

5.3 PROBES CONNECTION 7

5.4 SAFETY DIGITAL INPUTS AND PRESSURE SWITCHES 8

5.5 LOAD CONNECTIONS 8

6. MOUNTING & INSTALLATION 9

7. FIRST INSTALLATION 10

7.1 HOW TO SET THE KIND OF GAS 11

7.2 HOW TO SET THE RANGE OF THE PRESSURE PROBES 11

8. USER INTERFACE 12

8.1 DISPLAYING 12

8.2 KEYBOARD 12

8.3 ICONS 13

9. HOW TO SEE AND MODIFY THE SET POINT(S) 14

9.1 HOW TO SEE THE SET POINT OF COMPRESSORS AND/OR FANS 14

9.2 HOW TO MODIFY THE SET POINT OF COMPRESSORS AND/OR FANS 14

10. THE INFO MENU 14

11. PARAMETERS PROGRAMMING 15

11.1 HOW TO ENTER THE “PR1” PARAMETER LIST 15

11.2 HOW TO ENTER IN PARAMETERS LIST “PR2” 15

11.3 HOW TO CHANGE PARAMETER VALUES 16

12. HOW TO DISABLED AN OUTPUT 16

12.1 HOW TO DISABLED AN OUTPUT DURING A MAINTENANCE SESSION. 16

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 3/50

12.2 OUTPUT DISABLED SIGNALING. 16

12.3 REGULATION WITH SOME OUTPUTS DISABLED. 16

13. RUNNING HOURS OF LOADS 17

13.1 HOW TO DISPLAY THE RUNNING HOURS OF A LOAD. 17

13.2 HOW TO RESET THE RUNNING HOURS OF A LOAD. 17

14. ALARM MENU 17

14.1 HOW TO SEE THE ALARMS 17

15. KEYBOARD LOCKING 18

15.1 HOW TO LOCK THE KEYBOARD 18

15.2 TO UNLOCK THE KEYBOARD18

16. USE OF THE PROGRAMMING “HOT KEY “ 18

16.1 HOW TO PROGRAM A HOT KEY FROM THE INSTRUMENT (UPLOAD) 18

16.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD) 18

17. LIST OF PARAMETERS 18

17.1 PLANT DIMENSIONING AND TYPE OF REGULATION. 18

17.2 PROBES CONFIGURATION 21

17.3 CONFIGURABLE DIGITAL INPUTS CONFIGURATION 22

17.4 DISPLAY AND MEASUREMENT UNIT 23

17.5 COMPRESSOR REGULATION 24

17.6 LIQUID INJECTION THERMOSTAT 25

17.7 FANS REGULATION 25

17.8 ALARMS –COMPRESSOR SECTION 26

17.9 ALARMS –DLT SECTION 26

17.10 ALARMS –FANS SECTION 27

17.11 DYNAMIC SET POINT FOR FAN 27

17.12 ANALOG OUTPUT (OPTIONAL) 28

17.13 OTHER 29

18. TYPE OF REGULATION 29

18.1 DIGITAL COMPRESSOR REGULATION 29

18.2 PROPORTIONAL BAND REGULATION -ONLY FOR FANS 32

18.3 CONDENSERWITH INVERTER OR ECI FANS–ANALOG OUTPUT SETTING 34

19. ALARM LIST 34

19.1 TYPES OF ALARMS AND SIGNALING MANAGED 39

19.2 BUZZER MUTING 42

19.3 ALARM CONDITIONS –SUMMARY TABLE 42

20. TECHNICAL FEATURES 45

21. PARAMETERS –DEFAULT VALUES 45

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 4/50

1. BEFORE PROCEEDING

1.1 Check the sw rel. of the XC645D

1. Look at the SW rel. of XC64D printed on the label of the controller.

2. If the SW release is 3.4, proceed with this manual otherwise contact Dixell to get the

right manual.

2. GENERAL WARNING

2.1 Please read before using this manual

•This manual is part of the product and should be kept near the instrument for easy and quick

reference.

•The instrument shall not be used for purposes different from those described hereunder. It

cannot be used as a safety device.

•Check the application limits before proceeding.

•Dixell Srl reserves the right to change the composition of its products, even without notice,

ensuring the same and unchanged functionality.

2.2 Safety Precautions

•Check the supply voltage is correct before connecting the instrument.

•Do not expose to water or moisture: use the controller only within the operating limits avoiding

sudden temperature changes with high atmospheric humidity to prevent formation of

condensation

•Warning: disconnect all electrical connections before any kind of maintenance.

•The instrument must not be opened.

•In case of failure or faulty operation send the instrument back to the distributor or to “Dixell

S.r.l.” (See address) with a detailed description of the fault.

•Consider the maximum current which can be applied to each relay (see Technical Data).

•Ensure that the wires for probes, loads and the power supply are separated and far enough

from each other, without crossing or intertwining.

•Fit the probe where it is not accessible by the end user.

•In case of applications in industrial environments, the use of mains filters (our mod. FT1) in

parallel with inductive loads could be useful.

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 5/50

3. General description

The XC645D is designed to manage both compressors and fans in a condensing system such as

a pack.

The compressors can be digital scroll or Stream, simple, multistage.

Control is by means of a neutral zone and is based on the pressure or temperature sensed in the

LP suction (compressors) and HP (condenser) circuits. Aspecial algorithm balancesthe runhours

of the compressors to distribute the work load uniformly.

The controllers can convert both LP and HP pressures and displays them as temperatures.

The front panel offers complete information on the system’s status by displaying the suction and

condenser pressure (temperatures), the status of the loads, possible alarms or maintenance

conditions.

Each load has its own alarm input that is able to stop it when activated. To guarantee the total

system’s safety, there are also two inputs for low and high pressure switches: when these are

activated, the system is stopped.

By means of the HOT KEY the controller can be easy programmed at power on.

The controller can be connected to the X-WEB, controlling and monitoring system, thanks to the

RS485 serial output, using the standard ModBus RTU protocol.

4. COMPONENTS RELATED TO THE XC645D

Name

Description

Part number

4-20mA suction pressure transducer

PP11 (-0.5÷11bar)

BE009302 07

4-20mA condenser pressure transducer

PP30 (0÷30bar)

BE009302 04

Hot key for programming

HOT KEY 4K

DK00000100

4.1 PP07, PP11, PP30 PP50: 4÷20mA pressure transducers

PP07 2,0MT -0,5+7 bar rel FE cod BE009302 00

PP11 2,0MT -0,5+7 bar rel FE cod BE009302 07

PP30 2,0MT 0+30 bar rel FE cod BE009302 04

PP50 2,0MT 0+50 bar rel FE cod BE009002 05

4.2 NP4-67: pipe mounting temperature probe

The NP4-67 temperature probe

can be used on the discharge line

to monitor the discharge

temperature of the Digital Scroll

compressor.

NP4-67 1.5MT NTC probe

Measurement range: -40+110°C,

Cable 1,5mt

Code BN609001 52

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 6/50

5. WIRING & ELECTRICAL CONNECTIONS

5.1 General warnings

Before connecting cables make sure the power supply complies with the instrument’s

requirements.

Separate the probe cables from the power supply cables, from the outputs and the power

connections.

Do not exceed the maximum current allowed on each relay 5A resistive, in case of heavier

loads use a suitable external relay.

5.2 Wiring connections

NOTE

120V version: use terminals 47-48 for power supply: Terminals 44-45-46 operate at 120V

90-260V version: use terminals 47-48 for power supply: Terminals 44-45-46 operate at the same

voltage

24V version: use terminals 47-48 for power supply; Short circuit terminal 1-2.

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 7/50

5.3 Remote keyboard connection –Only for XC645D -7x0xx- or

XC645D -7x2xx-

**** ONLY FOR THE MODELS WITH 90-260Vac POWER SUPPLY

IDENTIFIED BY THE FOLLOWING PART NUMBERS: XC645D -7x0xx- or

XC645D -7x2xx-****

The VC660, remote keyboard for XC600D series, can be connected only to

the models with the above part numbers.

Use shielded 2 wires cable AWG 20, max allowed distance between

controller and keyboard: 30m.

Respect the polarity indications: as for the following table

XC645D -7x0xx- or XC645D -7x2xx-

VC660

Terminal:29 (+)

Terminal: 1 (+)

Terminal:30 (-)

Terminal: 3 (-)

5.4 Probes connection

5.4.1 General warnings

Pressure probe (4 - 20mA): respect the polarity. If using terminal ends be sure there are no bear

parts which could cause short circuiting or introduce noise disturbance at high frequencies. To

minimize the induced disturbances use shielded cables with the shield connected to earth.

Temperature probe: it is recommended to place the temperature probe away from direct air

streams to correctly measure the temperature.

5.4.2 Probe wirings

Low voltage side: Keep the cables away from the power cables. Use shielded cable to lengthen the

cables.

NOTE1: The PIN 38 is the common line for the temperature probes

NOTE2: The PIN 37 gives a 12Vdc supply for the 4-20mA pressure transducers

PP07 PP11, PP30, PP50 4÷20mA pressure

transducers respect the polarity.

Suction (P1C = Cur)

Brown (+) to terminal 37; white (-) to terminal 40

Condenser (P2C = Cur)

Brown (+) to terminal 37; white (-) to terminal 41

Temperature probes (NTC 10K)

Suction: 38-40 (P1C = NTC)

Condenser: 38-41 (P2C =NTC)

Pb3 (P3C = NTC): 38-42

Pb4 (P4C = NTC): 38-42

Ratiometric transducers (0.5÷4.5Vdc)

Suction (P1C = 0-5)

40 (In); 38(+); 39 (gnd)

Condenser (P2C =0-5)

41 (In); 38(+); 39 (gnd)

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 8/50

5.5 LOAD CONNECTIONS

!!!WARNING: Digital Scroll valve coil can operate at main voltage (230Vac or 115Vac) or

24Vac. In case of 24Vac short circuit terminals 1-2.

5.5.1 Connections for models at 230V or 115V and coil of digital valve at

115 or 230V.

5.5.2 Connections for models at 230V or 115V or 24V and coil of digital

valve at 24V.

5.6 SAFETY AND CONFIGURABLE DIGITAL INPUTS –FREE

VOLTAGE

5.6.1 Load safety inputs

Controller has 7 configurable digital inputs, free voltage.

Each digital input can be set by the related parameter iF01,.. iF07.

The first 4 digital inputs are factory pre-set to operate as safety input for loads.

Each input must collect the status of the safety devices related to the compressor such as

thermistors, pressure switches etc, when this input is activated the correspondence load is

switched off and not considered for the regulation.

The correspondence between loads (compressors or fans) and safety inputs is the following

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 9/50

LOAD

TERM.

SAFETY

INPUT

TERMINALS

SETTING

CONNECTION

Load 1

(digital)

5-6

Di1

13-14

iF01 = oA1

Load 2

7-8

Di2

13-15

iF02 = oA2

Load 3

9-10

Di3

16-17

iF03 = oA3

Load 4

11-12

Di4

16-18

iF04 = oA4

5.6.2 Additional Configurable digital inputs.

The controller XC645D is provided with 3 additional configurable digital inputs, one of them can

operate also as probe. Their functions are set by the parameter iF05, iF07 and iF08 respectively.

They can be used for liquid level monitoring, activate the energy saving function or silence mode

from a external devices.

The digital input connection is explain in the following table

Digital input

TERMINALS

Related parameter

CONNECTION

Digital input 5

19-20

iF05: function

iP05: polarity

First configurable

input/Probe 4

22-23 (i1F/Pb4)

iF07: function

iP07: polarity

Second

configurable d.i.

22-24 (i2F)

iF08: function

iP08: polarity

5.7 HP –LP Pressure switches connection

!!!WARNING: controller is provided with both free voltage digital inputs, and main voltage

inputs.!!!!

The main voltage inputs are designed for HP and LP pressure switches.

The low pressure switch has to be connected to the terminal 44 (line)and 45 (common)

The high pressure switch has to be connected to the terminal 45 (common) and 46 (line)

as shown on the following wiring diagram.

NOTE: the main voltage is related to the voltage supply of

the controllers.

Models at 115V or 230V the inputs operate at 115 or 230V.

Models at 24V the inputs operate at 24V.

5.8 Analog output connection

The controller supply up to 2 analog outputs, terminals, kind of output and functionality are shown

in the following table

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D 10/50

Terminals

Related parameter

Analog output 1

25[+] –26[-].

AOC: Kind of signal (4-20mA/0-10V)

AOF: function

Analog output 2

27[+] –28[-].

2AOC: Kind of signal (4-20mA/0-10V)

2AOF: function

5.9 How to connect monitoring system - RS485 Serial line

The Adr parameter is the number to identify each electronic board. Address duplication is not

permitted, in this case the communication with monitoring system is not guaranteed (the Adr is

also the ModBUS address).

1) Terminals [31] [+] and [32] [-].

2) Use shielded twisted cable. For example Belden® 8762 o

8772 or cat 5 cables.

3) Maximum distance 1Km.

4) Don’t connect the shield to the earth or to GND terminals

of the device, avoid accidental contacts by using insulating

tape.

6. Mounting & installation

The instruments are suitable only for internal use.

Instrument XC645D shall be mounted on an omega DIN rail

The ambient operating temperature range is between -10÷60°C.

Avoid locations subject to heavy vibration, corrosive gases or excessive dirt. The same applies to

the probes. Ensure ventilation around the instrument.

6.1 VC660 –KEYBOARD INSTALLATION

83,5

Keyboard VC660 shall be mounted on vertical panel,

in a 72x56 mm hole, and fixed using screws 3 x

2mm. To obtain an IP65 protection grade use the front

panel rubber gasket (mod. RGW-V).

Table of contents

Other Emerson Controllers manuals

Emerson

Emerson Fisher 161AY Series User manual

Emerson

Emerson Tartarini OS/66 User manual

Emerson

Emerson DIXELL XRi20CH Wiring diagram

Emerson

Emerson Dixell XR60CH Wiring diagram

Emerson

Emerson Fisher 630 Series User manual

Emerson

Emerson Bettis 500 User manual

Emerson

Emerson AMPGARD RVSS User manual

Emerson

Emerson Dixell XRi30T Wiring diagram

Emerson

Emerson Fisher Accu-Pressure Y693 User manual

Emerson

Emerson Bettis GVO-C Series Instruction Manual

Emerson

Emerson dixell XT111D Wiring diagram

Emerson

Emerson EL-O-Matic F-Series User manual

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS User manual

Emerson

Emerson Yarway 20-55 Quick guide

Emerson

Emerson Fisher FIELDVUE DVC6005 Series User manual

Emerson

Emerson Dixell XW60LH Wiring diagram

Emerson

Emerson AVENTICS 651 Series User manual

Emerson

Emerson Fisher Type B NG User manual

Emerson

Emerson E2 User manual

Emerson

Emerson Fisher 299H User manual

Emerson

Emerson Bettis Electro-Hydraulic Operated User manual

Emerson

Emerson Unidrive M400 User manual

Emerson

Emerson dixell XW60K User manual

Emerson

Emerson EC3-X32 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide