Emerson Asco SentronicPLUS User manual
Installation Manual
SentronicPLUS IO-Link CLASS A
Electronic Pressure Regulator
2
ASCO NUMATICS™
Visit our website at ASCO.com or contact us at (800) 972-2726
SentronicPLUS
INSTALLATION
MANUAL
ELECTRONIC
PRESSURE REGULATOR
SentronicPLUS Electronic Pressure Regulator
Electrical Characteristics
Nominal
Diameter DN
(mm)
Voltage * Max.
Power (W)
Max. Current
(mA)
Insulation
Class
Degree of
Protection Electrical Connection
324 VDC = ± 10% 12 500 FIP65 5-pin M12 connector or 7-pin DIN connector
624 VDC = ± 10% 24110001FIP65 5-pin M12 connector or 7-pin DIN connector
* Max. ripple: 10%
1For DN6, brass version G or H/1.8A, 44W
Specifi cations
Ø
Ports
Ø
Orifi ce DN
(mm)
Flow
CvFlow Factor (Kv Nm3/h) at 6 Bar (l/min - ANR)
1/8 NPT or GTap 30.21 (0.18) 210
1/4 NPT or GTap 60.70 (0.60) 700
General Valve Information
Fluid Temperature 0 ºC to 60 ºC (32 °F to 140 °F)
Command Signal- IO-Link
PSI Pressure Ranges:
PA & PB (50 & 100 psi ranges): in digital steps of 0.01 psi
PC (150 psi range): in digital steps of 0.1 psi
Bar Pressure Ranges:
40, 50, 60, V1, V2 & V3 (100mbar, 500mbar, 1bar & all vacuum): in digital
steps of 0.0001 bar
All others: in digital steps of 0.001 bar
Ports 1/8, 1/4 (NPT or GTap)
Construction Direct-operated Poppet Valve
Hysteresis 0.5% of span
Linearity/ pressure measurement ± 0.5% of span
Repeatability ± 0.5% of span
Fluids Ambient
Temperature Body Internal
Parts Seals
Air or neutral gas, ltered at 50 µm,
condensate-free, lubricated or
unlubricated
0 °C to 60 °C
(32 ºF to 140 ºF) Aluminum Stainless steel
and brass
NBR (nitrile) and
FPM ( uoroelastomer)
SentronicPLUS is a 3-way proportional valve with digital control.
•
Direct operated valve
•
Dynamic behavior (high speed)
•
IO - Link CLASS A Version
•
RoHS, REACH compliant
3
ASCO NUMATICS™
Visit our website at ASCO.com or contact us at (800) 972-2726
SentronicPLUS
INSTALLATION
MANUAL
ELECTRONIC
PRESSURE REGULATOR
Version
(ports)
, Body
0 = DN6 (G 1/4), ALU
4 = DN6 (NPT 1/4), ALU
7 = DN3 (G 1/8), Brass
8 = DN6 (G 1/4), Brass
9 = DN3 (NPT 1/8), Brass
A = DN6 (NPT 1/4), Brass
C = DN6 (G 1/4), Stainless Steel
Feedback
B = IO-LINK CLASS A
Control Panel
B = IO-LINK with display
C = IO-Link without display
Pressure Range Max. Inlet
Pressure
(psi)
2 (29)
2 (29)
2 (29)
3 (44)
8 (116)
8 (116)
8 (116)
12 (174)
12 (174)
12 (174)
12 (174)
14 (203)
Command Signal
B = IO-LINK CLASS A
Vacuum
(relative)
V1 = 0 to -1 bar
Shut-off valve,
connects to
vacuum on loss
of power
V2 = 0 to -1 bar
Bypass valve
V3 = 0 to -1 bar
Shut-off valve,
connects to
atmosphere on
loss of power
Absolute Pressure
Ranges Available
on Request
Digital Output
1 = Standard
Output Pressure
(psi)
40 = 0 – 0.1 bar (1.5)
50 = 0 – 0.5 bar (7.3)
60 = 0 – 1 bar (14.5)
02 = 0 – 2 bar (29)
03 = 0 – 3 bar (44)
PA = 0 – 3.4 bar (50)
05 = 0 – 5 bar (73)
06 = 0 – 6 bar (87)
PB = 0 – 6.9 bar (100)
10 = 0 – 10 bar (145)
PC = 0 – 10.3 bar (150)
12 = 0 – 12 bar (174)
Options
A00 = Dual loop control
018 = Oxygen clean
6 1 4 3 5 7 E 9011PB
How to Order
Operating Modes
Shut-o:
If the setpoint falls below 0.5 %, the coil current is switched o and the valve is fully exhausted.
Overtemperature:
If the temperature of the internal control electronics exceeds 100°C, the operating mode is switched to AUTOSAFE.
Undervoltage / overvoltage:
If the supply voltage is less than 18 V or more than 30 V, the coil current is switched o and the valve is fully
exhausted.
Autosafe:
If the coil current exceeds a certain value, dependent on the mechanics, for more than 20 seconds, the output
current is limited to max. 70% to prevent the valve from overheating.
4
ASCO NUMATICS™
Visit our website at ASCO.com or contact us at (800) 972-2726
SentronicPLUS
INSTALLATION
MANUAL
ELECTRONIC
PRESSURE REGULATOR
PE(4-8 deep)
3x1/4"-12 deep
1.02 (26)
0.39 (10)
1.18 (30)
1.78 (45.3)
0.43 (11)
2.18 (55.3)
4.15 (105.3)
4.52 (114.7)
1.42 (36)
2.68 (68)
2.05 (52)
1.69 (43)
1.38 (35) A) Thread M5 - depth 10
(on opposite side);
tapped through-hole
for M4 screw.
1/4 NPT or GTap
Weight: 1.87 (0.85)
1/8 NPT or GTap (DN3)
Weight: 1.21 (0.55)
PE (4-8 deep)
0.98 (25)
2.24 (57)
0.98 (25)
1.14 (29)
1.38 (35)
3 x 1/8"-8 deep
0.59 (15)
3.75 (95.2)
3.17 (80.5)
1.02 (26)
0.39 (10)
0.71 (18)
0.98 (25)
2xM4-10 deep
0.98 (25)
1.14 (29)
1.38 (35)
3.75 (95.2)
3.17 (80.5)
1.02 (26)
0.39 (10)
0.71 (18)
0.98 (25)
2 x M4-10 deep
Dimensions: Inches (mm), Weight in lbs. (kg)
5
ASCO NUMATICS™
Visit our website at ASCO.com or contact us at (800) 972-2726
SentronicPLUS
INSTALLATION
MANUAL
ELECTRONIC
PRESSURE REGULATOR
2
14
3
5
Pin Description
1+24 VDC Supply
2not connected
3+0 VDC Common (Supply)
4C/Q
5not connected
Body EMC shield
Connector Pin Out
M12 Class A & B Compatible Cables* and Accessories
M12 90° 5 Pin Female to Male Double Ended Cable - Unshielded
TD0505MIETA0571P – 5 Meter
TD0510MIETA0571P – 10 Meter
M12 90° 5 Pin Female Single Ended Cable - Unshielded
TD0505MIE000071P – 5 Meter
TD0510MIE000071P – 10 Meter
M12 Straight 5 Pin Female to Male Double Ended Cable - Unshielded
TC0505MIETA0571P – 5 Meter
TC0510MIETA0571P – 10 Meter
M12 Straight 5 Pin Female Single Ended Cable - Unshielded
TC0505MIE000071P – 5 Meter
TC0510MIE000071P – 10 Meter
*Reference our G3 Fieldbus catalog for M12 4 pin cables if the selected IO-Link®Master does not
accept 5 pin cables. Maximum IO-Link cable length is 20m.
6
ASCO NUMATICS™
Visit our website at ASCO.com or contact us at (800) 972-2726
SentronicPLUS
INSTALLATION
MANUAL
ELECTRONIC
PRESSURE REGULATOR
Installation and Operating Instructions
1. Before putting into operation carefully check all electrical connections and the supply voltage (24 VDC ±10 %).
Overload can destroy the electronics. Recommended pre-fuse T2.0 A.
2. The electrical connection is made with a round connector M12x1. The connector must meet the requirements of
DIN 60079-15.
WARNING:
Do not disconnect the plug while under voltage!
When disconnected from power, use supplied protection cover to ensure IP protection.
3. Use unshielded or shielded cables for the electrical connection of the valve. The shield, connector and control
cabinet must be EMC compliant. The valve body must be electrically connected to ground (PE, machine ground).
Do not run control cables parallel to high-voltage lines or servo-motor control cables.
4. The cable length between the IO-Link master and the valve must not exceed 20m.
5. Make sure that the valve is under pressure when a setpoint signal is applied to the valve (applying a setpoint
signal with no pressure on the valve will cause it to overheat).
6. The valve is factory adjusted.
7. The product must be returned to the factory for repair.
Warning
These products are intended for use in industrial compressed air systems only. Do not use these products where
pressures and temperatures can exceed those listed under SPECIFICATIONS.
Before using these products with uids other than those specied, for non-industrial applications, life-support systems,
or other applications not within published specications, consult ASCO Numatics.
Through misuse, age, or malfunction, components used in uid power systems can fail in various modes.
The system designer is warned to consider the failure modes of all component parts used in uid power
systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the
event of such failure.
System designers must provide a warning to end users in the operating manual if protection against a failure mode
cannot be adequately ensured.
System designers and end users are cautioned to review specic warnings found in instruction sheets packed and
shipped with these products.
ASCO (USA) | Tel (1) 888-686-2842 | an.insidesales@emerson.com | www.ASCO.com
Netherlands
(31) 33-277-7911
Singapore
(65) 6556-1100
South Korea
(82) 2-3483-1570
Spain
(34) 942-87-6100
United Kingdom
(44) 1695-713600
France
(33) 2-37-24-42-24
Germany
(49) 7237-9960
India
(91) 44-39197300
Italy
(39) 02-356931
Japan
(81) 798-65-6361
Mexico
(52) 55-5809-5640
Australia
(61) 2-9-451-7077
Brazil
(55) 11-4208-1700
Canada
(1) 519-758-2700
China
(86) 21-3395-0000
Czech Republic
(420) 235-090-061
Dubai - UAE
(971) 4-811-8200
Global Contacts
4/19
Table of contents
Other Emerson Controllers manuals
Emerson
Emerson Tarantini MN Quick guide
Emerson
Emerson TARTARINI FL Series User manual
Emerson
Emerson XM678D User manual
Emerson
Emerson PACSafe User manual
Emerson
Emerson Fisher 133H User manual
Emerson
Emerson PNC001-A Series User manual
Emerson
Emerson fisher 1008 User manual
Emerson
Emerson M200-01200024A10101AB100 User manual
Emerson
Emerson unidrive m User manual
Emerson
Emerson Lumity E3 User manual
Emerson
Emerson TARTARINI FL Series User manual
Emerson
Emerson XM678D Specification sheet
Emerson
Emerson Fisher L2e User manual
Emerson
Emerson Bettis RP3E User manual
Emerson
Emerson Dixell XT141C Wiring diagram
Emerson
Emerson Bettis Q series Instruction manual
Emerson
Emerson unidrive sp User manual
Emerson
Emerson Asco 642 Series User manual
Emerson
Emerson FISHER T208 Series User manual
Emerson
Emerson iPro User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
Airflow
Airflow Uno hab Installation and operating instructions
ABB
ABB ACS580-01 drives Hardware manual
Panasonic
Panasonic GM1 Series Reference manual
AutoAqua
AutoAqua Smart ATO micro SATO-120P manual
Panasonic
Panasonic FP? Positioning Unit RTEX Technical manual
Samson
Samson Type 5824 Mounting and operating instructions
