Electrolux EFDE317TIW0 User manual

EN FRONT LOAD DRYER

FR SÉCHEUSE Á CHARGEMENT FRONTAL

ES SECADORA DE CARGA FRONTAL

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES DE INSTALACIÓN

A07020301B January 2017

2Important Safety Instructions

Recognize safety symbols, words and

labels

Safety items throughout this manual are labeled

with a WARNING or CAUTION based on the risk

type as described:

• Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play.

Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing

suﬀocation. Place all materials in a garbage container or make materials inaccessible to children.

• Clothes dryer installation and service must be performed by a qualiﬁed installer, service agency or

the gas supplier.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• The electrical service to the dryer must conform with local codes and ordinances and the latest

edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical

code C22.1 part 1.

• The gas service to the dryer must conform with local codes and ordinances and the latest edition

of the National Fuel Gas Code ANSI Z223.1/NFPA 54, or in Canada, the Natural Gas and Propane

Installation Code, CSA B149.1. An individual manual shut-oﬀ valve must be installed within 6 ft (1.83

m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

• The dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest edi-

tions) for HOME USE only. This dryer is not recommended for commercial applications such as

restaurants, beauty salons, etc.

• Do not install a clothes dryer with ﬂexible plastic or ﬂexible foil venting material. Flexible venting

materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct

clothes dryer airﬂow and increase the risk of ﬁre.

• Do not stack a dryer on top of washer already installed on pedestal. Do not stack washer on top

of dryer. Do not stack washer on top of another washer.

• The instructions in this manual and all other literature included with this dryer are not meant to

cover every possible condition and situation that may occur. Good safe practice and caution

MUST be applied when installing, operating and maintaining any appliance.

Save these instructions for future reference.

This symbol alerts you to situations that may

cause bodily injury or property damage.

Table of contents

This symbol alerts you to situations that may

cause serious body harm, death or property

damage.

WARNING

For your safety the information in this manual must be followed to minimize the risk of ﬁre or

explosion or to prevent property damage, personal injury or loss of life. Do not store or use

gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other appliance.

Important Safety Instructions.....................................2

Installation Requirements........................................ 3-9

Installation Instructions..........................................10-17

Reversing Door..........................................................18-19

Options ............................................................................. 20

WARNING  RISK OF FIRE

Read all of the following instructions before installing and using this appliance:

Installation Requirements

Adjustable

pliers

4 inch, rigid metal or

semi-rigid metal exhaust duct work

4 inch rigid metal or

Adjustable

wrench

Metal foil tape

(not duct tape)

External

vent hood

Carpenter’s level

Phillips, straight, &

square bit screwdrivers

Optional universal

accessory

wrench

Pipe wrench

for gas

supply

gas line

shutoff valve

(gas dryer)

LP-resistant

thread tape

(for natural gas

or LP supply)

½” NPT union flare

adapters (x2) and

flexible gas supply line

(gas dryer)

3-wire or 4-wire

240 volt cord kit

(electric dryer)

4 in.

(10.2 cm)

clamp

Tools and materials needed for installation:

Please read and save this

guide

Thank you for choosing Electrolux, the premium

brand in home appliances. These Installation

Instructions are part of our commitment to

customer satisfaction and product quality

throughout the life of your new appliance.

Questions?

Installation Checklist

240v Electric Supply (Electric Dryer)

Approved NEMA 10-30 or 14-30 service

cord with all screws tight on terminal

block

Approved strain relief installed

Terminal access cover installed before

initial operation

Door Reversal

Follow detailed instructions in this guide

Test hinge and latch for function

Electrical Power

House power turned on

Dryer plugged in

Final Checks

Installation Instructions and Use and

Care Guide read thoroughly

Door latches and drum tumbles when

cycle starts

Registration card sent in

Exhaust Venting

Free-ﬂowing, clear of lint buildup

4 inch (102 mm) rigid or semi-rigid ducting

of minimal length and turns

NO foil or plastic venting material

Approved vent hood exhausted to

outdoors

Leveling



Dryer is level, side-to-side and front-to-

back

Cabinet is sitting solid on all corners

Gas Supply (Gas Dryer)

Manual shutoﬀ valve present in supply

All connections sealed with approved

sealer and wrench tight

Conversion kit for LP system

Gas supply turned on

No leaks present at all connections -

check with soapy water, NEVER check with

ﬂame

For toll-free telephone support in the U.S.:

1-877-4ELECTROLUX (1-877-435-3287) and in

Canada: 1-800-265-8352.

For online support and product information visit

www.electroluxappliances.com.

WARNING

FIRE HAZARD

●Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

●Do not install a booster fan in dryer exhaust

duct.

●Install all clothes dryers in accordance with

the installation instructions in this manual.

4Installation Requirements

Electrical system requirements

ELECTRICAL REQUIREMENTS FOR ELECTRIC

DRYER:

CIRCUIT - Individual 30 amp. branch circuit

fused with 30 amp. time delay fuses or circuit

breakers. Use separately fused circuits for

washer and dryer. DO NOT operate a washer

and a dryer on the same circuit.

POWER SUPPLY - 3-wire or 4-wire, 120/240 volt,

single phase, 60 Hz, Alternating Current.

3-WIRE POWER SUPPLY CORD (not supplied)

OUTLET RECEPTACLE - NEMA 14-30R

receptacle to be located so the power supply

cord is accessible when the dryer is in the

installed position.

GROUNDING CONNECTION - See “Grounding

requirements” in Electrical Installation section.

OUTLET RECEPTACLE - NEMA 10-30R

receptacle to be located so the power supply

cord is accessible when the dryer is in the

installed position.

GROUNDING CONNECTION - See “Grounding

requirements” in Electrical Installation section.

The dryer MUST employ a 3-conductor power

supply cord NEMA 10-30 type SRDT rated at

240 volt AC minimum, 30 amp, with 3 open

end spade lug connectors with upturned

ends or closed loop connectors and marked

for use with clothes dryers. For 3-wire cord

connection instructions see ELECTRICAL

CONNECTIONS FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLY CORD (not supplied)

The dryer MUST employ a 4-conductor

power supply cord NEMA 14-30 type SRDT

or DRT (as required) rated at 240 volt AC

minimum, 30 amp, with 4 open end spade

lug connectors with upturned ends or closed

loop connectors and marked for use with

clothes dryers. For 4-wire cord connection

instructions see ELECTRICAL CONNECTIONS

FOR A 4-WIRE SYSTEM.

ELECTRICAL REQUIREMENTS FOR GAS DRYER:

CIRCUIT - Individual, properly polarized and

grounded 15 amp. branch circuit fused with 15

amp. time delay fuse or circuit breaker.

POWER SUPPLY - 2-wire, with ground, 120 volt,

single phase, 60 Hz, Alternating Current.

POWER SUPPLY CORD - The dryer is equipped

with a 120 volt 3-wire power cord.

GROUNDING CONNECTION - See “Grounding

requirements” in Electrical Installation section.

Grounding type

ll receptacl

ll receptacle

wer cord with

3-prong

ounded plug

Do not,

under

y cir

cumstances,

cut,

remo

ve,

or b

ypass th

ypass the

ounding pr

ong.

3-wire receptacle

(NEMA type 10-30R)

4-wire receptacle

(NEMA type 14-30R)

NOTE

Because of potentially inconsistent voltage

capabilities, the use of this dryer with power

created by gas powered generators, solar

powered generators, wind powered generators

or any other generator other than the local utility

company is not recommended.

NOTE

Dryers manufactured for sale in Canada have

factory-installed, 4-wire power supply cord

(NEMA 14-30).

NOTE

A 120/208 volt, single phase, 60 Hz, Alternating

Current supply may be used on dryers marked

for use on the rating plate.

IMPORTANT

This dryer is internally grounded to neutral un-

less it was manufactured for sale in Canada.

Only a 4-conductor cord shall be used when

the appliance is installed in a location where

grounding through the neutral conductor is

prohibited. Grounding through the neutral link

is prohibited for: (1) new branch circuit installa-

tions, (2) mobile homes, (3) recreational ve-

hicles, and (4) areas where local codes do not

permit grounding through the neutral.

Installation Requirements

Gas supply requirements

Exhaust system requirements

If your present system is made up of plastic duct

or metal foil duct, replace it with a rigid or semi-

rigid metal duct. Also, ensure the present duct is

free of any lint prior to installing dryer duct.

Use only 4 inch (102 mm) diameter (minimum)

rigid or ﬂexible metal duct and approved vent

hood which has a swing-out damper(s) that

open when the dryer is in operation. When the

dryer stops, the dampers automatically close to

prevent drafts and the entrance of insects and

rodents. To avoid restricting the outlet, maintain

a minimum of 12 inches (30.5 cm) clearance

between the vent hood and the ground or any

other obstruction.

CORRECT

INCORRECT

The following are speciﬁc requirements

for proper and safe operation of your

dryer.

1. Installation MUST conform with local codes,

or in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1 (latest

edition).

2. The gas supply line should be 1/2 inch (1.27

cm) pipe.

3. If codes allow, ﬂexible metal tubing may be

used to connect your dryer to the gas supply

line. The tubing MUST be constructed of

stainless steel or plastic-coated brass.

4.The gas supply line MUST have an individual

shutoﬀ valve installed in accordance with the

B149.1, Natural Gas and Propane Installation

Code.

5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping,

accessible for test gauge connection, MUST

be installed immediately upstream of the gas

supply connection to the dryer.

6. The dryer MUST be disconnected from the

gas supply piping system during any pressure

testing of the gas supply piping system at test

pressures in excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the gas

supply piping system during any pressure

testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig (3.45

kPa).

8. Connections for the gas supply must comply

with the Standard for Connectors for Gas

Appliances, ANSI Z21.24/CSA 6.10.

WARNING

EXPLOSION HAZARD

Uncoated copper tubing will corrode when

subjected to natural gas, causing gas leaks.

Use ONLY black iron, stainless steel, or plastic-

coated brass piping for gas supply.

WARNING

FIRE HAZARD

Failure to follow these instructions can create

excessive drying times and ﬁre hazards.

WARNING

FIRE HAZARD

Do not install a clothes dryer with ﬂexible

plastic or metal foil venting materials. Flexible

venting materials are known to collapse, be

easily crushed and trap lint. These conditions

will obstruct clothes dryer airﬂow and increase

the risk of ﬁre.

WARNING

FIRE HAZARD

●Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

●Do not install a booster fan in dryer exhaust

duct.

●Install all clothes dryers in accordance with

the installation instructions in this manual.

6Installation Requirements

The dryer must be connected to an exhaust

outdoors. Regularly inspect the outdoor exhaust

opening and remove any accumulation of lint

around the outdoor exhaust opening and in the

surrounding area.

EXHAUST DIRECTION

Directional exhausting can be accomplished

by installing a quick-turn 90° dryer vent elbow

directly to exhaust outlet of dryer. Dryer vent

elbows are available through your local parts

distributor or hardware store.

Exhaust system requirements, continued

Number of 90° turns

MAXIMUM LENGTH

of 4” (102 mm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

4”

(10.2 cm) louvered

2.5”

(6.35 cm)

0 125 ft. (38 m) 110 ft. (33.5 m)

1 115 ft. (35 m) 100 ft. (30.5 m)

2 105 ft. (32 m) 90 ft. (27.5 m)

3 95 ft. (29 m) 80 ft. (24.5 m)

4 85 ft. (26 m) 70 ft. (21.5 m)

NOTE

Use of 90° quick-

turn elbow required

to meet minimum

installation depth.

WARNING

FIRE HAZARD

A clothes dryer must be exhausted outdoors.

Do not exhaust dryer into a chimney, a wall,

a ceiling, an attic, a crawl space or any

concealed space of a building. A clothes

dryer produces combustible lint. If the dryer

is not exhausted outdoors, some ﬁne lint

will be expelled into the laundry area. An

accumulation of lint in any area of the home

can create a health and ﬁre hazard.

WARNING

FIRE HAZARD

Exceeding the length of duct pipe or number

of elbows allowed in the “MAXIMUM LENGTH”

charts can cause an accumulation of lint in

the exhaust system. Plugging the system could

create a ﬁre hazard, as well as increase drying

times.

WARNING

FIRE HAZARD

●Do not allow combustible materials (for

example: clothing, draperies/curtains, paper)

to come in contact with exhaust system.

The dryer MUST NOT be exhausted into a

chimney, a wall, a ceiling, or any concealed

space of a building which can accumulate

lint, resulting in a ﬁre hazard.

●Do not screen the exhaust ends of the

vent system, or use any screws, rivets or

other fasteners that extend into the duct

to assemble the exhaust system. Lint can

become caught in the screen, on the

screws or rivets, clogging the duct work and

creating a ﬁre hazard as well as increasing

drying times. Use an approved vent hood

to terminate the duct outdoors, and seal all

joints with metal foil tape. All male duct pipe

ﬁttings MUST be installed downstream with

the ﬂow of air.

WARNING

FIRE HAZARD

●Do not install ﬂexible plastic or ﬂexible foil

venting material.

●If installing semi-rigid venting, do not exceed

8 ft. (2.4 m) duct length.

See also CLEARANCE

REQUIREMENTS on the

next page.

Installation Requirements

In installations where the exhaust system is not

described in the charts, the following method

must be used to determine if the exhaust system

is acceptable:

Exhaust system requirements, continued

CORRECT INCORRECT

1. Connect an inclined or digital manometer

between the dryer and the point the exhaust

connects to the dryer.

2. Set the dryer timer and temperature to air ﬂuﬀ

(cool down) and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure MUST NOT be

higher than 1.0 inch of water column. If the

system back pressure is less than 1.0 inch of

water column, the system is acceptable. If

the manometer reading is higher than 1.0 inch

of water column, the system is too restrictive

and the installation is unacceptable.

Although vertical orientation of the exhaust

system is acceptable, certain extenuating

circumstances could aﬀect the performance of

the dryer:

●Only the rigid metal duct work should be

used.

●Venting vertically through a roof may expose

the exhaust system to down drafts causing

an increase in vent restriction.

●Running the exhaust system through an

uninsulated area may cause condensation

and faster accumulation of lint.

●Compression or crimping of the exhaust

system will cause an increase in vent

restriction.

●The exhaust system should be inspected and

cleaned a minimum of every 18 months with

normal usage. The more the dryer is used,

the more often you should check the exhaust

system and vent hood for proper operation.

Manufactured or mobile home installation

1. Installation MUST conform to current

Manufactured Home Construction & Safety

Standard, Title 24 CFR, Part 32-80 (formerly

the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD Part

280) or Standard CAN/CSAZ240 MH.

2. Dryer MUST be exhausted outside (outdoors,

not beneath the mobile home) using metal

ducting that will not support combustion.

Metal ducting must be 4 inches (10.16 cm) in

diameter with no obstructions. Rigid metal duct

is preferred.

3. If dryer is exhausted through the ﬂoor and

area beneath the mobile home is enclosed,

the exhaust system MUST terminate outside

the enclosure with the termination securely

fastened to a non-combustible portion of the

mobile home structure.

4. Refer to previous sections in this guide for

other important exhaust venting system

requirements.

5. When installing a gas dryer into a mobile

home, a provision must be made for outside

make up air. This provision is to be not less

than twice the area of the dryer exhaust

outlet.

6. Installer MUST anchor this (1) dryer or (2)

dryer mounted on pedestal to the ﬂoor with

approved Mobile Home Installation Kit - P/N

137067200.

Install male ﬁttings in correct direction:

WARNING

FIRE HAZARD

Do not install the dryer where gasoline or

other ﬂammables are kept or stored. If the

dryer is installed in a garage, it must be a

minimum of 18 inches (45.7 cm) above the ﬂoor.

Failure to do so can result in death, explosion,

ﬁre or burns.

8Installation Requirements

MIN INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Under-

Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.5 cm)

Clearance requirements

60 sq. in.

(387.1cm²)

3”

(7.6cm)

60 sq. in.

(387.1cm²)

3”

(7.6cm)

INSTALLATION IN A RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom,

recess or closet, MUST be exhausted

outdoors.

2. No other fuel burning appliance shall be

installed in the same closet as the gas dryer.

3. Your dryer needs the space around it for

proper ventilation.

DO NOT install your dryer in a closet with a

solid door.

4. Closet door ventilation required: A minimum

of 120 square inches (774.2 cm²) of opening,

equally divided at the top and bottom of

the door, is required. Openings should be

located 3 inches (7.6 cm) from bottom and

top of door. Openings are required to be

unobstructed when a door is installed. A

louvered door with equivalent air openings

for the full length of the door is acceptable.

closet door

* F

or other than straight back venting, a quick-turn

90° dryer vent elbow must be installed to achieve

0” (0 cm) installation.

IMPORTANT

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water or

outside weather conditions.

2. In an area where it will come in contact with

curtains, drapes, or anything that will obstruct

the ﬂow of combustion and ventilation air.

3. On carpet. Floor MUST be solid with a maxi-

mum slope of 1 inch (2.5 cm).

NOTE

To achieve an installation with 0” (0 cm)

clearance for the back of the dryer (for other

than straight back venting), a quick-turn 90°

dryer vent elbow must be installed as described

previously in this manual.

0”

(0 cm)

0”

(0 cm)

1”

(2.5 cm)

0”

(0 cm)

Installation Requirements

Dryer dimensions

*Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.

1Power supply cord length on gas dryer or electric Canadian dryer approximately 60 inches (152.5 cm).

2Drain hose length on washer approximately 59 inches (150 cm).

3Power supply cord length on washer approximately 60 inches (152.5 cm).

electrical

supply on

rear of unit1

gas supply

pipe on rear

of gas unit

centerline

height of

rear vent

53.2” (135 cm)*

to clear open door

31.6” (80 cm)*

to front of closed door 27.0”

(68.5 cm)

13.5”

(34.5 cm)

to center of

rear vent

ﬂoor line

freestand dryer

on ﬂoor

dryer mounted on

optional pedestal

38.0”

(96.5 cm)

53.25”

(135.5 cm)

17.0”

(43 cm)

19.0”

(48 cm)

3.7”

(9.5 cm)

1.5”

(4 cm)

3.75”

(9.5 cm)

electrical

supply on

rear of unit1

gas supply

pipe on rear

of gas unit

approved stacking

kit (STACKIT7X)

required for

stacked installation

centerline

height for

rear vent

53.5” (136 cm)*

to clear open door

32.0” (81.25 cm)*

to front of closed door

75.75”

(192.5 cm)

41.0”

(105 cm)

39.0”

(99 cm)

water supply

connection on

rear of unit

drain hose on

rear of unit2

power cord on

rear of unit3

ﬂoor line

10 Installation Instructions

Electrical installation

NOTE

Dryers operating on 208 volt power supply will

have longer drying times than dryers operating

on 240 volt power supply.

The following are speciﬁc requirements for

proper and safe electrical installation of your

dryer. Failure to follow these instructions can

create electrical shock and/or a ﬁre hazard.

Grounding requirements - Electric dryer (USA)

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event

of a malfunction or breakdown, grounding

will reduce the risk of electrical shock by

providing a path of least resistance for

electrical current.

2. After you purchase and install a 3 wire or 4

wire power supply cord having an equipment-

grounding conductor and a grounding plug

that matches your wiring system, the plug

MUST be plugged into an appropriate, copper

wired receptacle that is properly installed and

grounded in accordance with all local codes

and ordinances. If in doubt, call a licensed

electrician.

3. DO NOT modify the plug you’ve installed

on this appliance. If it will not ﬁt the outlet,

have a proper outlet installed by a qualiﬁed

electrician.

For a permanently connected dryer:

1. The dryer MUST be connected to a grounded

metal, permanent wiring system; or an

equipment grounding conductor must be run

with the circuit conductors and connected to

the equipment-grounding terminal or lead on

the appliance.

WARNING

Improper grounding of the dryer may cause

serious injury or death. Check with a licensed

electrician if you are in doubt as to whether

the appliance is properly grounded.

WARNING

ELECTRICAL SHOCK HAZARD

●This appliance MUST be properly grounded.

Electrical shock can result if the dryer is not

properly grounded. Follow the instructions in

this manual for proper grounding.

●Do not use an extension cord with this dryer.

Some extension cords are not designed to

withstand the amounts of electrical current

this dryer utilizes and can melt, creating

electrical shock and/or ﬁre hazard. Locate

the dryer within reach of the receptacle for

the length power cord to be purchased,

allowing some slack in the cord. Refer to the

pre-installation requirements in this manual

for the proper power cord to be purchased.

WARNING

ELECTRICAL SHOCK HAZARD

●A U.L.-approved strain relief must be

installed onto power cord. If the strain relief

is not attached, the cord can be pulled

out of the dryer and can be cut by any

movement of the cord, resulting in electrical

shock.

●Do not use an aluminum wired receptacle

with a copper wired power cord and plug

(or vice versa). A chemical reaction occurs

between copper and aluminum and can

cause electrical shorts. The proper wiring

and receptacle is a copper wired power

cord with a copper wired receptacle.

Table of contents

Other Electrolux Dryer manuals

Electrolux

Electrolux TE1120 User manual

Electrolux

Electrolux TW SL3 M100 User manual

Electrolux

Electrolux EDS6051 User manual

Electrolux

Electrolux EDC 5369 Operation manual

Electrolux

Electrolux EDH3284PDW User manual

Electrolux

Electrolux TW GL4 E User manual

Electrolux

Electrolux EIED50LIW Installation instructions

Electrolux

Electrolux EW8H1968IS User manual

Electrolux

Electrolux EDC 67130W User manual

Electrolux

Electrolux EDE 45100 W User manual

Electrolux

Electrolux EDE1070PDW User manual

Electrolux

Electrolux QuickDry QDC User manual

Electrolux

Electrolux EWED65H SS User manual

Electrolux

Electrolux EDC47130W User manual

Electrolux

Electrolux LAVATHERM 58860 User manual

Electrolux

Electrolux T4290 Owner's manual

Electrolux

Electrolux EDV606E User manual

Electrolux

Electrolux EDC 510E User manual

Electrolux

Electrolux WT31RT Instruction Manual

Electrolux

Electrolux TK SL 3E User manual

Electrolux

Electrolux T4900 User manual

Electrolux

Electrolux EDH97950W User manual

Electrolux

Electrolux EDH803R9WB User manual

Electrolux

Electrolux EDE 425 M Quick guide

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions

Frigidaire

Frigidaire CAQE7077KW0 use & care

Bosch

Bosch WTX8HKM9SN User manual and installation instructions