ElectrIQ ECOSILENT8 User manual

USER MANUAL

ECOSILENT8

ECOSILENT8E

ECOSILENT10

ECOSILENT10E

8,000 BTU

electriQ PORTABLE AIR CONDITIONER

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and keep it

safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

10,000 BTU

CONTENTS

SAFETY

FEATURES AND PARTS LIST

INSTALLATION

OPERATION

REMOTE CONTROL

CLEANING AND MAINTENANCE

EMPTYING THE INTERNAL WATER TANK

TROUBLESHOOTING

ERROR CODES

SUPPORT

TECHNICAL SPECIFICATION

SAFETY INSTRUCTIONS

Important!

• Carefully read the instructions before operating the unit

• This appliance is for indoor use only.

• Rating: This unit must be only connected to a 220-240 V / 50 Hz

earthed outlet.

• Installation must be in accordance with regulations of the country where the unit is

used.

• If you are in any doubt about the suitability of your electrical supply have it checked

and, if necessary, modied by a qualied electrician.

• This air conditioner has been tested and is safe to use. However, as with any electrical

appliance - use it with care.

• Disconnect the power from the appliance before dismantling, assembling or cleaning.

• Avoid touching any moving parts of the appliance.

• Never insert ngers, pencils or any other objects though the guard

• This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities. It is also not intended for use by those with a

lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their

safety.

• Do not leave children unsupervised with this appliance.

• Do not clean the unit by spraying it or immersing it in water.

• Never connect the unit to an electrical outlet using an extension cord. If an outlet is

not available, one should be installed by a qualied electrician.

• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is

not stretched or exposed to sharp objects/edges.

• A damaged supply cord should be replaced by the manufacturer or a qualied

electrician in order to avoid a hazard.

• Any service other than regular cleaning or lter replacement should be performed by

an authorised service representative. Failure to comply could result in a voided

warranty.

• Do not use the appliance for any purpose other than its intended use.

• The air conditioner unit must always be stored and transported upright, otherwise

irreparable damage may be caused to the compressor; if in doubt we suggest waiting

at least 24 hours before starting the unit.

• Avoid restarting the air conditioning unit unless 3 minutes have passed since being

turned off. This prevents damage to the compressor.

• Never use the mains plug as a switch to start and turn off the air conditioning unit. Use

the provided ON/OFF button located on the control panel.

• Always place the unit on a dry and stable surface.

• The appliance should not be installed in laundry or wet rooms.

• The appliance must be placed in a room without sources of ignition (for example: open

ames, an operating gas appliance or an operating electric heater).

• R290 refrigerant gas complies with European environmental directives.

• R290 has a low GWP (Global Warming Potential) of 3.

• The ECOSILENT8 / 8E contains about 220 g of R290 refrigerant gas.

• The ECOSILENT10 / 10E contains about 280 g of R290 refrigerant gas.

• Do not use or store in an unventilated space with an area smaller than 10.6 m2per unit

(ECOSILENT8 / 8E) or 13.4 m2 per unit (ECOSILENT10 / 10E).

• The room must be such as to prevent stagnation of possible leaks of refrigerant gas as

there could be a danger of re or explosion should the refrigerant come into contact

with electric heaters, stoves or other sources of ignition.

• Refrigerant gas may be odourless.

• Do not use the product and contact the retailer for advice, if damage has occurred to

the unit which may have compromised the refrigerant system.

• Any repairs or maintenance must only be carried out on the unit by a suitably qualied

engineer. Before opening and servicing the unit the authorised engineer must be in

possession of a copy of the manufacturer’s service manual and must follow the safety

information contained within it to ensure all hazards are minimized.

• The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airow from the outlet or inlet grills.

• For maximum performance the minimum distance from a wall or objects should be

50cm.

• Keep the lters clean. Under normal conditions, lters should only need cleaning once

every three weeks (approximately). Since the lters remove airborne particles, more

frequent cleaning maybe necessary, depending on the air quality.

• For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees

lower than the current room temperature. After, set appliance to your desired

settings.

• To protect the unit, we recommend not using the cooling function when the ambient

temperature is higher than 35oC.

FEATURES AND PARTS LIST

FEATURES

• 3 in 1 Cooling, Fan, Dehumidier great for Rooms up to 20 sqm.

• 5 speed DC fan: balancing quiet operation with performance.

• SmartCool Logic for Improved Energy Efciency.

• 24 Hours Start / Stop Timer

• Digital Thermostat.

• Remote Control.

• Castors and Handles for Enhanced Portability.

• Auto-Restart to retain the settings in the event of power failure.

Control Panel Top Cover

Rear Housing

Carry Handle

Louvres

Front Cover

PART LIST

Castors

Upper Air Inlet

Exhaust Outlet

Lower Air Inlet

Power Cable

Exhaust Hose Window Slide Bar

INSTALLATION

INSTALLATION OF WINDOW KIT

WARNING: Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another.

While moving the unit please note that it must always be kept upright and then placed on an even surface.

1. Attach the shtail connector to the end of the hose, by

extending the end and twisting until rmly attached (At least

3 full rotations).

2. Attach the connector on the opposite end of the pipe to the exhaust

outlet on the rear of the appliance by putting into position and twisting to

lock in place.

The window kit (slide bar and shtail) can be used

with sliding windows and doors. For other types of

window, the shtail should be used on its own.

1. Partially open the window and place

the extended slide bar in position

before closing the window onto it.

2. Fix the shtail adaptor into the

opening on the slide bar

3. Fix the exhaust connector on the

opposite end of the exhaust hose to

the exhaust outlet on the rear of the

air conditioner.

3. Make sure the unit is upright and there are no obstructions to

the air inlets and outlet grills.

50CM

NOTES:

• The window kit is only designed to be installed with sliding or sash windows or doors. The window

kit is not designed to be used with any other style of windows.

• The sh tail adaptor can be used without the slide bar with most windows / doors.

• When using the air conditioner ensure that the opening around the shtail adaptor is as small as

possible to ensure the efciency of the unit is not reduced.

• The best form of installation is through a wall duct. By properly venting you expel hot air from your

room while efciently cooling it.

• Your air conditioner should be used without the vent pipe in dry mode. When using dry mode

ensure that an external water tank is used, monitored and regularly emptied before overowing.

Permanent plumbing can be also installed or an external uplift water pump can be set up to allow

for uninterrupted use.

IMPORTANT SAFEGUARDS

The length of the soft hose extends from approximately 30 cm to 180 cm. If hose is extended above this

length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well

ventilated and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short

as possible and avoid bending the air hose by more than 30 degrees in order not to reduce the

performance of the unit.

OPERATION

Swing Mode Timer Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing Mode Timer Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing

Mode

Timer Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing

Mode Timer Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing Mode Timer Sleep

Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing Mode Timer

Sleep

Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing Mode

Timer

Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing Mode Timer Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Swing Mode Timer Sleep Speed

Timer

High

Low

Mid

Power

Cool

Dry

Fan Sleep

Smart Cool

Press the POWER button to turn the unit ON or OFF.

Press the MODE button to cycle between the 4 modes, the indicator for the selected mode will

be illuminated.

COOL: The room is cooled with the cold air expelled through the front air outlet while hot air is

expelled through the vent pipe. The desired room temperature can be set between 17 and 30

degrees using the + and – buttons, and the fan speed can be changed using the SPEED button.

FAN: The fan speed can be changed pressing the SPEED button.

DRY: Should be operated without the vent hose, but with continuous drainage to remove

moisture from the air. The display will show dH and the unit will run in low fan speed.

SMART COOL: An intelligent cooling mode where the fan speed is automatically adjusted based

on the amount of cooling required. Attempts to change the fan speed will move the unit into

COOL mode.

Repeatedly press the SPEED button to cycle through the five fan speeds. Each time the SPEED

button is pressed, the fan speed will be displayed. The fan speed can be changed between F1

(Low) to F5 (High). The LED indicators will also illuminate to show the fan speed as below:

F1 –Low, F2 – Low and Mid, F3 – Mid, F4 – Mid and High, F5 – High.

The fan speed cannot be changed in SMARTCOOL and DRY modes.

Press to enter sleep mode. The sleep indicator will be illumined and all other indicators will be

turned off. In sleep mode, the appliance works at low fan speed. Press SLEEP again to exit sleep

mode.

The timer functions cannot be combined or repeated.

POWER ON TIMER

With the appliance in standby, press the TIMER button to set the power-on timer. Use the + and

- buttons to adjust the duration of the timer (1 to 24 hours). The Timer indicator will turn on and

the unit will start after the selected number of hours.

POWER OFF TIMER

With the appliance running with the desired settings, press the TIMER button to set the power-

off timer. Use the + and - buttons to adjust the duration of the timer (1 to 24 hours). The timer

indicator will illuminate and the unit will stop after selected number of hours.

Used to adjust the temperature in COOL/SMART COOL mode and to set the duration of the TIMER.

The buttons are not used in FAN or DRY modes. Press both buttons together to change between

displaying the temperature in Celsius and Fahrenheit.

Press this button to enable the swing function. The louvres will slowly move from side to side. If

swing is pressed again the louvres will stop in their current position.

Press and hold the swing button to turn off the status indicators on the control panel.

FROST PROTECTION

In COOL, DRY or SMART COOL modes, if the temperature of the exhaust is too low, the machine will

automatically stop operating until the temperature has risen.

OVERFLOW PROTECTION

When the water in the internal water tank exceeds the warning level, the machine will stop operating and

sound an alarm with the LCD display showing “E7”. To resume operation empty the internal water tank. After

the water is emptied, the machine will automatically return to the original state.

AUTO-DEFROST

The machine has automatic defrosting function. If during operation the temperature of the internal coils drops

too low, the unit will enter auto defrost and the heating symbol will ash on the control panel.

AUTOMATIC THERMAL PROTECTION

To protect the service life of the machine, the machine has automatic thermal protection. If the temperature

within the unit is outside of the specied range, the compressor and the lower motor will stop operation. The

appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION

To prevent damage to the compressor there is a 3 minute delay start protection function.

POWER Press to turn the unit on or off.

TIMER Press to set the timer.

DOWN Press to decrease the desired temperature or

timer duration.

UP Press to increase the desired temperature or

timer duration.

SLEEP Press the sleep button to enter sleep mode.

FAN Press to enter fan / air purify mode.

COOL Press to enter cool mode.

DRY Press to enter dry (dehumidify) mode.

HIGH Press to enter high (F5) speed fan.

LOW Press to enter low (F1) speed fan.

NOTE: The design of the remote may vary from the diagram, due to

continuous product improvement.

REMOTE CONTROL

MULTI PROTECTIVE FUNCTIONS

MAINTENANCE AND CLEANING

PLEASE SHUT OFF THE UNIT AND UNPLUG FROM THE MAINS BEFORE CLEANING OR PERFORMING ANY

MAINTENANCE

CLEAN THE SURFACE

Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol,

gasoline, etc; otherwise, as this may cause damage to the surface and or the internal workings of the

machine

AIR FILTER CLEANING

If the lter screen is clogged with dust, the effectiveness of the air conditioner is reduced. The lter screen

should be cleaned once every two weeks or as often as necessarily in your environment.

CLEAN THE UPPER FILTER SCREEN FRAME

Grip the edge of the evaporator lter screen frame with both hands. Pull out to remove the lter screen

from its frame. If present, unscrew the screws xing the lter before removing it (as shown in the above

gure).

Put the evaporator lter screen into warm water with neutral detergent (about 40oC /104oF) and dry it in

the shade after rinsing clean.

CLEAN THE LOWER FILTER SCREEN FRAME

Hold the handle of the air inlet lter screen frame, and pull it outward gently to remove it.

Put the lter screen into warm water with neutral detergent (about 40oC/ 104 oF) and dry it in the shade

after rinsing clean.

This manual suits for next models

Table of contents

Other ElectrIQ Air Conditioner manuals

ElectrIQ

ElectrIQ ECOSILENT8-V2 User manual

ElectrIQ

ElectrIQ P15C User manual

ElectrIQ

ElectrIQ iQool9PLUS-V2 Operating manual

ElectrIQ

ElectrIQ P16HP User manual

ElectrIQ

ElectrIQ eiQ-CRFC18K Manual

ElectrIQ

ElectrIQ iQool9B Operating manual

ElectrIQ

ElectrIQ AIRFLEX15-V2 User manual

ElectrIQ

ElectrIQ ECOSILENT10HPW User manual

ElectrIQ

ElectrIQ ECOSILENT10W User manual

ElectrIQ

ElectrIQ CMAC20M User manual

ElectrIQ

ElectrIQ eiQ-3MS9K9K9K Operating manual

ElectrIQ

ElectrIQ AIRFLEX 15 User manual

ElectrIQ

ElectrIQ A1/CMAC10M User manual

ElectrIQ

ElectrIQ P15HP User manual

ElectrIQ

ElectrIQ P12C-V2 User manual

ElectrIQ

ElectrIQ eiQ-12K12KC24KWMINV Operating manual

ElectrIQ

ElectrIQ AIRCUBE User manual

ElectrIQ

ElectrIQ P12CE-V2 User manual

ElectrIQ

ElectrIQ P18HP User manual

ElectrIQ

ElectrIQ iQool9 User manual

ElectrIQ

ElectrIQ ECOSILENT12HPWE User manual

ElectrIQ

ElectrIQ AIRFLEX 15 User manual

ElectrIQ

ElectrIQ AIRFLEX15 User manual

ElectrIQ

ElectrIQ SILENT16-V2 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual