Eaton MEMSHIELD 4 User manual

MEMSHIELD 4 INSTALLATION INSTRUCTIONS FOR

EM4PBKEL404/EM4PBKEL804 EARTH LEAKAGE MODULES

Instruction leaflet LT1227 (01/19)

IMPORTANT NOTES

1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician in

accordance with current electrical engineering Codes of Practice, Requirements for the Electrical Installations (IET Wiring

Regulations BS7671), Construction (Design and Management) Regulations, HSG150 - Health and Safety in Construction, Statutory

requirements and any Specific instruction issued by the Company.

2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of the

person responsible for its future operation and maintenance, and is at all times available for ready reference.

3. These notes assume throughout that the product is disconnected from the supply. It is essential that this is done before any

work is carried out.

4. These Panelboards are only designed for use with Eaton MCCBs. Failure to comply will result in invalid warranty and

certification.

Items supplied with Earth Leakage Modules

M8 x 16mm long screw 2 Qty

M8 Hexagon Nut/washer 2 Qty

M6 x 16mm long screw 4 Qty

M6 Hexagon Nut 4 Qty

M6 External Tooth Washer 8 Qty

M5 x 8mm self tapping screw 2 Qty

Cable Ties 12 Qty

Cable Tie Bases 4 Qty

2.5mm² Double Insulated Grey/Brown) Cable 2.8 metres

2.5mm² Double Insulated Grey/Blue Cable 2.8 metres

2.5mm² Cable Ferrules 2 Qty

2.5mm² x M8 Ring Connector 2 Qty

1.5mm² Grey Cable 2 metres

1.5mm² Cable Ferrules 6 Qty

Shunt Trip 1 Qty

Earth Leakage Module assembly instructions

1. Align the Module to the bottom of the Panelboard and fix together with provided screws: 4 x M6 screws and nuts; 8 x external

tooth washers on either side of the joint to break the paint for earth continuity.

2. Fit the Shunt Trip provided to the incoming MCCB.

3. Fit the terminal block assembly (Fig.1) to the Panelboard. Using the DIN rail as template, mark the position of the 2 fixing

holes. Drill 2 x 4.3mm dia holes and secure the terminal block assembly using the M5 x 8mm screws provided.

Fig.1 Terminal Block Assembly

Warning -

Intellectual Property Rights

Eaton wishes to make it clear that it owns intellectual property rights in the

product which it manufactures (whether or not listed in this leaflet) and that it

will take legal action against any party found to be manufacturing, using, or

selling any article which infringes the company’s intellectual property. All

marks in this document identified with an R symbol or a TM symbol adjacent

to the mark are trademarks of Eaton.

The use to which this product is put and its place of installation is outside our

control. Particular care should therefore be taken to follow the instructions

given here and to ensure their continued availability in conjunction with the

use of the product.

No responsibility can be accepted by us if these instructions are disregarded.

Further copies of these instructions and information concerning the

installation and proper use of this product can be obtained by contacting the:

Technical Services Department

Eaton Electric Limited, Middleton, Manchester, M24 1GQ.

Tel: +44(0)8700 545 333,

email: techsup[email protected]

SUPPLY

4. Connect the Shunt Trip wire C1 (400A Board) / YELLOW (800A Board) to the Live terminal and C2 (400A Board) / WHITE

(800A Board) to the Neutral terminal of the Terminal block using the ferrules provided.

5. Connect the terminal block Live to terminal 1 of the relay and the terminal block Neutral to the bottom Neutral terminal of

the Fuse Disconnector using the 1.5mm² cable and ferrules provided.

6. Connect the live busbar to terminal 1 of the Fuse Disconnector using the 2.5mm² double insulated (grey/brown) cable,

ferrule and M8 screw and nut/washer provided. (Fig.2)

7. Connect the Neutral Busbar to the top Neutral terminal of the fuse Disconnector using the 2.5mm² double insulated

(grey/blue) cable, M8 screw and nut/washer provided. (Fig.2)

8. Cable Ties and Bases are provided to secure the Line Voltage and Neutral cables.

NOTE: All Terminal Cable connections 1.0Nm

M8 Screw connections 12-15Nm

Fig.3 Top Entry

When fitting Top Entry move the CT in the Earth Leakage

module as shown. Connect as instructions above.

Wiring Diagram

Fig.2 Connection to Live / Neutral Busbars

Fuse Disconnector

Earth Leakage Relay - adjustable

Current Transformer

This manual suits for next models

Other Eaton Control Unit manuals

Eaton

Eaton Cuttler-Hammer Pow-R-Command 100 Manual

Eaton

Eaton NEMA 12 User manual

Eaton

Eaton BBA 16 Series Manual

Eaton

Eaton Cutler-Hammer IQMSSPM User manual

Eaton

Eaton ELCM Series User manual

Eaton

Eaton XTPAXENCS65B Manual

Eaton

Eaton ePDU G3 Datasheet

Eaton

Eaton DeviceNet User manual

Eaton

Eaton CBEU-02/03 User manual

Eaton

Eaton PowerXL DX-NET-ETHERCAT-2 Manual

Eaton

Eaton RF96APM User manual

Eaton

Eaton 5PX EBM 72V RT2U User manual

Eaton

Eaton mMINT Quick start guide

Eaton

Eaton SmartWire-DT SWD Series User manual

Eaton

Eaton Power Xpert PXGMS Programming manual

Eaton

Eaton DX-NET-BACNETMSTP Manual

Eaton

Eaton VICKERS SystemStak User manual

Eaton

Eaton EP Control User manual

Eaton

Eaton CEAG DLS/3PH-BUS-Module-inverse Service manual

Eaton

Eaton XNE-1SWIRE User manual

Eaton

Eaton DXE-EXT-SET Manual

Eaton

Eaton Vickers SF4-140-20-002-10 User manual

Eaton

Eaton Digitrip RMS 910 Manual

Eaton

Eaton Cutler-Hammer PanelMate ePro PS Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual

Flyron

Flyron FN-BC04 user manual