Eaton 145406 Installation and operating instructions

QRV 9100

Installation, Operation

and Maintenance of

Airflex®Quick Release

Valve

Forward this manual to the person responsible

for Installation, Operation and Maintenance of

the product described herein. Without access to

this information, faulty Installation, Operation or

Maintenance may result in personal injury or

equipment damage.

Use Only Genuine Airflex®Replacement Parts.

The Airfiex Division of Eaton Corporation recommends

the use of genuine Airfiex replacement parts. The use of

non-genuine Airflex replacement parts could result in

substandard product performance, and may void your

Eaton warranty. For optimum performance, contact

Airflex:

In the U.S.A. and Canada:(800) 233-5926

Outside the U.S.A. & Canada: (216) 281-2211

Internet: www.airflex.com

October, 1987

(Revised : November, 2006)

203977

Note: This manual pertains to the AIRFLEX

DIAPHRAGM OPERATED QUICK RELEASE

VAVLE which is identified by its silver housing. If

your valve housing is anodized green, service it

according to manual QRV 9090 or replace the entire

valve with the diaphragm style.

QRV 9100 (PDF FORMAT) 1

AIRFLEX®QUICK RELEASE VALVE

Figure 1 : Quick Release Valve

TABLE 1:

QRV MODEL and KIT NUMBERS

QRV

SIZE

BASIC QRV

MODEL and KIT

NUMBER

QRV OPTIONS and KITS OPTION and KIT

DESIGNATION***

3/8", 1/2" and 3/4" Size 1"

3/8 145406

w/Metal Sleeve DE BD

w/Rubber Sleeve DF

w/Inlet Pipe Thread DG

1/2 145407

w/Metal Sleeve & Muffler** DS BE

w/Rubber Sleeve & Muffler** DR

w/Inlet Pipe Thread & Muffler** DT

3/4 145141

w/Metal Sleeve & Pipe Adapter DL BR

w/Metal Sleeve & 1/4 Pipe Adapter* DM

1” 146506

Diaphragm & End Cap Kit DP DP

Diaphragm, Muffler & End Cap Kit DQ DQ

*1/4 NPT adapter for 3/8 QRV only.

** Mufflers are not factory-assembled to QRV. See Installation section.

*** The option and kit designation letters must be added as a suffix to the basic model number to completely

identify the QRV model or kit. Diaphragm and end cap kit contains a diaphragm, end cap and sealant. Dia-

phragm, muffler and end cap kit contains diaphragm, end cap, muffler and sealant.

1.0 INTRODUCTION

Throughout this manual there are a number of

HAZARD WARNINGS that must be read and

adhered to in order to prevent possible personal

injury and/or damage to equipment. Three sig-

nal words “DANGER”, “WARNING” and

“CAUTION” are used to indicate the severity of

a hazard, and are preceded by the safety alert

symbol

Denotes the most serious hazard, and is

used when serious injury or death WILL

result from misuse or failure to follow spe-

cific instructions.

Used when serious injury or death MAY

result from misuse or failure to follow spe-

cific instructions.

Used when injury or product/equipment

damage may result from misuse or failure to

follow specific instructions.

It is the responsibility and duty of all personnel

involved in the installation, operation and main-

tenance of the equipment on which this device

is used to fully understand the:

procedures by which hazards can be avoided.

1.1 Description

The Airflex®QRV is a quick release valve that

facilitates the release of air from a pressurized

chamber i.e., air cylinders, clutches, brakes or

other pneumatic devices. In essence it provides

an exhaust port at the chamber rather than

exhausting through long supply lines and con-

trol components. The function they perform is

especially important in high speed cycling

equipment. They prevent sluggish operation,

overlap and excessive wear. Their importance

in an air control system cannot be overempha-

sized.

QRV’s are available in four sizes for direct con-

nection to 3/8, 1/2, 3/4 and 1 inch pipe. Models

are also available which permit 1/2, 5/8 and 3/4

inch outside diameter tubing connections to the

QRV inlet port.

Exhaust noise from the valve can be reduced

by using a muffler, which threads into the

tapped hole in the end cap.

1.2 How It Works

Figure 2

The Airflex QRV contains a diaphragm

designed to function on a pressure differential.

Air pressure at the valve inlet seats the dia-

phragm on the end cap, closing the exhaust

port. Applied pressure, acting on the outer

unsupported diaphragm area, deflects it and

allows air to flow to the cylinder port. See Fig-

ure 2.

When a pressure drop occurs in the air supply,

the pressure differential lifts the diaphragm from

the exhaust port and seats it on the inlet port.

Air from the pressurized device can now flow

freely to atmosphere through the valve’s

exhaust port.

If the cylinder pressure falls below the inlet

pressure, the pressure differential on the dia-

phragm will close the exhaust port, preventing

further exhaust.

QRV 9100 (PDF FORMAT)

1.3 Specifications

Maximum operating pressure:

150 PSI (10.3 Bar)

Minimum sealing pressure:

2 PSI (.14 Bar)

Air quality: Clean and dry to avoid contamina-

tion of housing and diaphragm. Any additives

used in the air supply must be compatible with

valve materials.

Operating temperature range:

-40°F (-40°C) to 120°F (49°C)

Mean life: Over 5 million cycles 75 PSI (5.1

Bar) and 80°F (27°C).

Diaphragm material: Polyurethane

Housing material: Zinc alloy

End cap material: Noryl®

GRAPHIC SYMBOLS:

Figure 3

2.0 INSTALLATION

Before performing any work, read this manual

and study all figures. Assure yourself that you

understand and can do what is required in each

step. Failure to follow these instructions may

affect quick release valve operation and may

result in exposure to personal injury.

Before installing the valve, set and block the

machine or equipment in a secure position;

close the air shutoff valve and exhaust air

from air lines; and disconnect all electrical

power.

2.1 Air Piping

2.1.1 For fastest response time, use an inlet pipe size

equal to or larger than the quick release valve size.

Minimize the length of pipe between the quick

release valve and air control valve. Keep the number

of fittings, bends and other restrictions in the inlet line

to a minimum.

2.1.2 Piping should be free of foreign material such as pipe

thread sealant, metal chips, etc. Pipe and tubing

ends must be reamed after cutting to prevent a

reduction of effective pipe or tube diameter.

Do not allow foreign matter to enter the

quick release valve. Particles of foreign

matter can prevent diaphragm sealing and

cause air leakage.

2.1.3 Refer to 1.3 for air quality, additives and allowable

operating pressures.

Table 2:

PORT SIZES

QRV Size Inlet Cylinder

3/8 3/8 NPT or 1/2 OD Tube 3/8 NPT

1/2 1/2 NPT or 5/8 OD Tube 1/2 NPT

3/4 3/4 NPT or 3/4 OD Tube 3/4 NPT

1 1" OD Tube 1" NPT

Table 3:

FLOW CAPACITY IN SCFM(m3/min)*

QRV Size Inlet to Cylinder Cylinder to

Exhaust

3/8 121 (3.4) 206 (5.8)

1/2 172 (4.9) 256 (7.2)

3/4 287 (8.1) 376 (17.2)

1 Contact Factory

*At 100 PSIG (6.9 Bar) inlet pressure with full pres-

sure drop.

QRV 9100 (PDF FORMAT) 4

2.2 Mounting

2.2.1 Screw the cylinder port of the quick release valve into

the female port of the device using a minimum of

pipe thread sealant. Use a wide, flat faced wrench

which will not crimp or damage the valve body. The

quick release valve must be torqued enough to pro-

duce a tight seal, but not more than the value given in

Table 4.

Do not position the quick release valve

exhaust port in the up position or allow for-

eign matter to enter the valve housing. Parti-

cles of foreign matter will enter the exhaust

air stream and/or prevent diaphragm seating.

Either condition could result in personal

injury or damage to equipment.

Position the quick release valve exhaust port

so that the exhaust air stream does not

strike operating personnel. Particles of for-

eign matter picked up by the air stream can

cause personal injury.

Position the quick release valve exhaust port

so that there are no restrictions to the

exhaust air flow. Any restriction will slow

down the valve response time.

2.2.2 If the quick release valve has pipe threads on the

inlet port, make a direct pipe connection. Do not

exceed the tightening torques given in

Table 4.

2.2.3 For quick release valves having tubing connections,

slide the nut and sleeve onto the inlet air tubing and

insert the tubing or pipe adapter into the valve hous-

ing until it bottoms. Slide the sleeve into its seat in the

housing. Tighten the nut sufficiently to produce an air

seal but not more than the value given in Table 4.

2.2.4 If a muffler is to be used, install per the following

instructions.

Loctite® must be used where called for in

the following procedure. Mufflers installed

without Loctite® may work loose during

operation resulting in personal injury.

Note : Quick release valves supplied prior to Sep-

tember, 1989 do not have threaded end caps to

accept the muffler. The end caps on these valves

must be replaced. Refer to the Maintenance sec-

tion in this manual for end cap replacement.

Note : Mufflers are not factory-assembled to the

quick release valves due to possible interference

with the rims of Airfiex clutch elements. When a

quick release valve having a muffler is ordered, a

basic valve is supplied along with a muffler/end

cap/diaphragm kit. If only the muffler is to be

installed, discard the end cap and diaphragm

included in the kit.

2.2.4.1 Thoroughly clean the female threads in the quick

release valve end cap and the male threads on the

muffler.

2.2.4.2 Apply Loctite®#222 (included in the kit) to the

threads on the muffler, using one drop per thread,

and screw the muffler into the end cap. Torque the

muffler to 60 lb.-in. (7 Nm).

2.3 Testing

2.3.1 Apply air pressure to the quick release valve. The

valve and its connections should not leak under pres-

sure. If the valve leaks, refer to the Maintenance sec-

tion in this manual.

2.3.2 Cycle the valve several times to ensure proper oper-

ation. If the valve response time appears sluggish,

check for restrictions in the air supply line.

Table 4:

Maximum Allowable Tightening

Torque

QRV Size Torque

3/8 40 lb. ft. (54 Nm)

1/2

50 lb. ft. (67 Nm)3/4

QRV 9100 (PDF FORMAT) 5

3.0 MAINTENANCE

Before performing any work, read this manual

and study all figures. Assure yourself that you

understand and can do what is required in

each step. Failure to follow these instructions

may affect quick release valve operation and

may result in personal injury.

Two quick release valve replacement kits are

available for valve rebuilding. An end cap/dia-

phragm kit is available for valves not having

mufflers, and contains an end cap, diaphragm

and tube of Loctite®#222. An end cap/dia-

phragm/muffler kit contains all of the above

along with a muffler. It is advisable to stock at

least one spare quick release valve for each

size used in an installation.

The quick release valve should be periodically

checked for proper functioning. If the valve fails

to seal, it should be inspected internally. Usually

foreign material will be found which has been

carried through the piping. If a valve becomes

ineffective after prolonged service, it can be

restored to good operating condition by rebuild-

ing.

3.1 Valve and Diaphragm Service

Before performing any work on the valve, set

and block the machine or equipment in a

secure position; close the air shutoff valve

and exhaust all air from the air lines; and dis-

connect all electrical power in order to pre-

vent personal injury and/or equipment

damage.

3.1.1 If the quick release valve exhaust port is positioned

downward, it will be difficult to service the diaphragm.

It is recommended that the valve be removed from

the equipment and bench-serviced.

3.1.2 Use a flat faced wrench to unscrew the muffler (if

present) and the end cap. The diaphragm may fall

out of the housing at this time. Discard the end cap,

muffler and diaphragm.

Note : The end caps on quick release valves man-

ufactured prior to September, 1989, have hex-

shaped exhaust ports to accommodate an allen

wrench for end cap removal. Refer to Table 5 for

the appropriate wrench size to remove the end

cap. Discard after removal.

3.1.3 If the diaphragm did not fall out of the housing, gently

pry along its outside diameter, being careful not to

damage the sealing surface on the housing.

3.1.4 Inspect the diaphragm sealing surface in the housing

(shown on figure) If the surface is worn, scratched or

corroded, the entire quick release valve must be

replaced.

Figure 4

Do not attempt to renew the diaphragm seal-

ing surface by sanding or machining.

Machining the surface will increase the dia-

phragm operating gap and cause the valve to

malfunction.

3.1.5 Thoroughly clean the inside of the housing and the

internal threads in the housing.

Table 5:

End Cap Allen Wrench Size

QRV Size Width Across Flats

3/8 1/2”

1/2

3/4”

3/4

1N/A

Do not allow foreign matter to enter either

the valve housing or muffler. Particles of for-

eign matter can prevent diaphragm sealing.

3.1.6 Insert a new diaphragm into the housing so it bot-

toms against the inlet port.

Loctite®must be used where called for in the

following procedure. An end cap and/or muf-

fler installed without Loctite®may work

loose during operation resulting in personal

injury or equipment damage.

3.1.7 Remove and discard the protective cap from the

replacement end cap. Apply Loctite®#222 to the

threads of the end cap, using one drop per thread,

and screw the end cap into the housing. Make sure

the diaphragm is located properly in the housing.

Torque the end cap to 60 lb-in. (7Nm).

3.1.8 If there is sufficient swing clearance on the equip-

ment, the muffler (if applicable) may be installed at

this time; otherwise, install the quick release valve

and muffler onto the equipment per the Installation

section of this manual. When installing the muffler, do

not forget to use Loctite®#222 on the muffler threads

and torque to 60 lb.-in. (7Nm).

3.2 Testing

3.2.1 Test by applying air pressure to the valve. The valve

should not leak under pressure. Removing the air

pressure should cause the diaphragm to shift and

allow the air to exhaust through the end cap and

muffler. If the valve does not function properly, repeat

the servicing procedure.

4.0 Ordering Information/Technical

Assistance

4.1 In any correspondence regarding Airflex quick

release valves, always refer to the size and port

configuration and call or write:

Loctite is a registered trademark of Henkle Technolo-

gies.

Noryl is a registered trademark of The General Elec-

tric Company.

Eaton Corporation

Airflex Division

9919 Clinton Road

Cleveland, Ohio 44144

Tel.: (216) 281-2211

Fax: (216) 281-3890

Internet : www.airflex.eaton.com

Form ML-318

Revised September 3, 1997

EATON PRODUCT WARRANTY

Subject to the conditions stated herein, Eaton

Corporation warrants to the Purchaser that

each new Airflex Product manufactured by

Eaton will be free from failures caused by

defects in material and workmanship, and will

deliver its rated capacity, for a period of twelve

(12) months from the date of shipment to Pur-

chaser, provided such Product is properly

installed, properly maintained, operated under

normal conditions and with competent supervi-

sion. Warranty claims shall, be made in writing

and the part or parts shall, if requested by Air-

flex Division, be returned prepaid to the Airflex

Division for inspection.Upon a determination

that a defect exists, Eaton shall thereupon cor-

rect any defect, at its option either by repairing

any defective part or parts or by making avail-

able at Eaton’s plant a repaired or replacement

part. This warranty does not extend to normal

wear parts or components of the Product, such

as friction material and friction surfaces.

LIMITATION OF WARRANTY

THE FOREGOING WARRANTY IS EXCLUSIVE

AND IN LIEU OF ALL OTHER WARRANTIES

WHETHER WRITTEN, ORAL OR IMPLIED. ANY

IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE

ARE SPECIFICALLY EXCLUDED.

In no event shall Eaton be liable for special,

incidental or consequential damages. Eaton’s

liability arising out of the supplying of such

Product, or its use, whether in warranty, con-

tract or otherwise, shall in no case exceed the

cost of correcting defects in the Products as

herein provided. Upon expiration of the twelve

(12) month period, all such liability shall termi-

nate. THE FOREGOING SHALL CONSTITUTE

THE SOLE REMEDY OF PURCHASER AND THE

SOLE LIABILITY OF EATON.

Eaton Corporation

Airfiex Division

9919 Clinton Road

Cleveland, Ohio 44144

This manual suits for next models

Table of contents

Other Eaton Control Unit manuals

Eaton

Eaton Power Xpert C445 Manual

Eaton

Eaton SystemStak DGM-5-30 Series User manual

Eaton

Eaton Form 4D Recloser Control User manual

Eaton

Eaton ePDU G3HD User manual

Eaton

Eaton MEMSHIELD 4 User manual

Eaton

Eaton XIOC-SER Manual

Eaton

Eaton Vickers DG3V-8 Series User manual

Eaton

Eaton Eaton 5PX Assembly instructions

Eaton

Eaton NZM2-XMVR Manual

Eaton

Eaton Char-Lynn VersaSteer 10 Series Owner's manual

Eaton

Eaton DXE-EXT-SET Manual

Eaton

Eaton DXE-EXT-SET Manual

Eaton

Eaton Ampgard AR User manual

Eaton

Eaton Powerware 9125 User manual

Eaton

Eaton P1 I2 Series Manual

Eaton

Eaton ELC-COENETM User manual

Eaton

Eaton PKE-SWD-32 Manual

Eaton

Eaton BreakerVisu NZM-XMC-MDISP35-MOD User manual

Eaton

Eaton EC4E-221-6D4T1 User manual

Eaton

Eaton CBEU-02/03 User manual

Eaton

Eaton Box 1 Operation and maintenance manual

Eaton

Eaton DXC-EXT-LOCSIM Manual

Eaton

Eaton Vickers FCGT-02-A-11 Series User manual

Eaton

Eaton Vickers SF4-140-20-002-10 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual

Flyron

Flyron FN-BC04 user manual