Durafly T-28 TROJAN User manual
Please read this manual carefully
before operating this plane.
(PNF)
INSTRUCTION
MANUAL
CONTENTS
Introduction
Specifications
Contents Of Box
Required To Complete Model
Assembly
Setting Up Your Model
1
1
2
2
3-6
7-9
Model Flying Precautions
Pre-flight Checks
10
10
Flying Your T-28 Trojan
T-28 Trojan TIPS
Spare Parts Listing
11
12
13
Trouble Shooting 14
Contact
Notes
15
16
SPECIFICATION
- Wingspan:1100mm (43.3in)
- Length: 930mm (35.4in)
- Flying Weight:1460g (52oz)
- Controls: 7 Channel (Ail, Ele, Thro, Rud, Flap, Gear, Airbrake)
- Motor: Aerostar 3536 750Kv brushless outrunner.
- Prop: 10x6 3-Blade
- ESC: Aerostar 40amp
- Battery: 4S 14.8V 25C 2200mah 4S
- Channels: 7 Channel Tx and Rx
INTRODUCTION
Thank you for purchasing the Durafly T-28 Trojan. This airplane was built based on the original
North American Aviation T-28 Trojan.
With the Durafly T-28 Trojan you can now experience what made this great model a classic. From
the perfectly captured outline to the super scale details. The T-28 Trojan uses environmentally safe
water-based paint, with retractable landing gear, LED Navigational Lighting sytem, under fuselage
air brake, and even the stickers are 100% the same as the original. Like all other Durafly models,
the T-28 Trojan also has all electronics pre-installed, all major components assembled for you, and
a full compliment of tools and accessories included. No glue is provided, since none is needed! The
T-28 Trojan screws together in just 6 easy steps, with multiple hatches allowing easy access to
internal electronics. We went one step further and included a wooden camera holder allowing you
to install your FPV equipment and experience the thrill of flying your T-28 Trojan in a whole different
way!
The Durafly T-28 Trojan, you deserve to have one.
1
2
4. Propeller
5. Wood Camera Holder
6. Accessories Set
1. Fuselage
2. Main Wing
3. Horizontal tail
OrangeRX R620X
6Ch 2.4Ghz:
Part No. 9171000757-0
REQUIRED TO COMPLETE MODEL:
Turnigy 2200mAh
4S 14.4V 30C Lipo:
Part No. T2200.4S.30
OrangeRx T-SIX 2.4GHz 6CH
Programmable Tx:
Part No. 9403000001 Mode 1
9403000002 Mode 2
In its ‘Plug n Fly’ format the T-28 still requires some additional electronic components to get it
‘flight ready’. Durafly recommends the products below for optimum performance and great value.
Available at
hobbyking.com
CONTENTS
ASSEMBLY
3
2. Install the horizontal tail to the fuselage as shown.
1. Locate the bag marked “Aileron” and “Flap”. Install aileron and flap control horns and rods for
each side of the wing as shown. Ensure the servo horn is at 90 degrees to the wing when installing
the rod.
4
4. Locate the bag marked “Rudder” Install the control horns on the vertical tail. Connecting the pre
installed control rods to the outer hold of the control horn.
3. Locate the bag marked “Elevator”Install horizontal tail, control horns and rods with the supplied
bolts as shown. Ensure tail is firmly secured and aligned.
A.
Note: It is recommended that you balance the prop and spinner before
installing for optimum performance and efficiency.
5
6. The final stage of assembly is to mount propeller. Slide prop onto motor shaft, engaging molded
hex detail on back of propeller to hex fitting on prop shaft. Tighten prop nut to shaft firmly by hand.
5. Mount the wing to the fuselage with the supplied bolts. Make sure to feed servo wires into
passage to fuselage compartment, ensuring no wires are pinched in the wing saddle.
Congratulations, basic assembly of your T-28 Trojan is now complete.
Please perform a final check on all screws, bolts and components,
ensuring all are secure and firmly in place.
6
Ailerons and Flaps Elevator Rudder
Elevator
10-20mm
10-20mm
10-18mm
10-18mm
50-60mm
12-18mm
12-18mm
Aileron
Rudder
3. The T-28 Trojan handles very well in flight warbird high speed handling, trainer-like low speed.
Before you fly your T-28 Trojan please follow the recommended settings below for optimum
handling and performance..
*Elevator ‘low rates’ 10mm ‘high rates’ 20mm in either direction from neutral.
*Rudder ‘low rates’ 10mm ‘high rates’ 18mm in either direction from neutral.
*Aileron ‘low rates’ 12mm ‘high rates’ 18mm in either direction from neutral.
SETTING UP YOUR MODEL:
1. With your receiver installed and all servos plugged into their corresponding channels, connect
the flight battery to the ESC to power up the electronics. With the model now armed, ensure all
servos are centered and all control surfaces are level. If not, adjust by turning the control clevises
by hand accordingly until the control surfaces are level as shown.
Note: For safety reasons, it is advised that this is done with the prop removed from the
model.
Control throws:
7
Table of contents
Other Durafly Toy manuals
Durafly
Durafly EFXTRA User manual
Durafly
Durafly PRIME TUNDRA User manual
Durafly
Durafly Messerschmitt BF.109E-4 User manual
Durafly
Durafly Spitfire Mk1a User manual
Durafly
Durafly GOBLIN User manual
Durafly
Durafly Bonanza User manual
Durafly
Durafly Das Ugly Stik User manual
Durafly
Durafly Curtiss P-40N User manual
Durafly
Durafly SlowPoke User manual
Durafly
Durafly BRAVADO User manual
Durafly
Durafly AUTO-G2 User manual
Durafly
Durafly Sky Mule User manual
Durafly
Durafly Ugly Stick User manual
Durafly
Durafly Excalibur V2 User manual
Durafly
Durafly Tomahawk User manual
Durafly
Durafly BF-110 Parts list manual
Durafly
Durafly EXCALIBUR User manual
Durafly
Durafly Spitfire MK2A Plug and Fly 1100mm... User manual
Durafly
Durafly Micro Tundra PNF User manual
Durafly
Durafly Retro Series Junior models Plug and Fly User manual
