Dorma TS93 T User manual

Installation instructions:

Pull side jamb mount with dead stop (T)

Optional hold open (TH)

TS93 T/TH

—

Surface applied door closer

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]

08279211 06/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

TABLE OF CONTENTS

—

Technical specifications

Note

1. Drawing is not to scale.

2. Dimensions are in inches/[mm].

3. Right hand door is shown.

4. Caution: sex nuts are required for attachment of

components to unreinforced doors and to wood or

plastic faced composite type fire doors, unless an

alternative method is identified in the individual door

manufacturer's listings.

5. Template is for 4-1/2 x 4-1/2 butt hinges & 3/4" offset

pivots

6. Maximum door opening degree is 175°.

7. Minimum door width 24".

Templates

Closer overall

Technical specifications

Templates 2

Size selection chart 2

Closer setup

Exploded parts list

Handing of the door 3

A. Installing the surface closer

Installing the backplate

Installing the surface closer 4

B. Adjustments

Adjusting the closing speeds

Adjusting the spring force 6

Adjusting the optional hold open 7

C. Installing the closer covers

Installing the covers 7

Contents

NOTE: Refer to the included drawing for pull side door closer, back plate mounting templating.

Size selection chart

Door Width

Closer Interior/

Exterior

2'-0"

min.

2'-6"

max.

3'-0"

max.

3'-6"

max.

4'-0"

max.

4'-6"

max.

5'-0"

max.

TS9315 Interior • • N/A N/A

TS9356 Interior N/A N/A N/A N/A • ••

8. Hold open range is from 50° to 140° with optional hold

open kit.

9. Use closer body style "B" for this installation.

10. Arrows on mounting plate point upward.

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]

08279221 06/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

TS93 T/TH

—

Closer setup

Handing of the door

Follow included template to properly prepare door and

frame for all accessories of the closer installation.

Know the swing of the door which is being installed prior

to installation.

Make sure door efficiently operates prior to installing

closer.

Hinge Hinge

Exterior side of door

Interior side of door

Left hand door (LH)

Left hand reverse

door (LHR)

Right hand reverse

door (RHR)

Right hand door (RH)

The surface closer is comprised of the following components.

1. Closer body: "B" body

2. Main arm

3. Track assembly

4. Pinion

5. Cover and end caps

6. Track cover

7. Closing/sweep speed adjustment

8. Latch speed adjustment

9. Backcheck adjustment

10. Delayed action adjustment

Verify closer spring size prior to installation. See "Size

selection chart" on page 2.

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]

08279221 06/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

TS93 T/TH

—

Reference template 08279222

NOTE: For use on T-mount applications (closer on door, track

on frame) on the pull side of the door.

1.1 Attach the back plate to the installing surface using the

four screws [10-32 machine screws or #10 wood screws]

provided with the surface closer.

Installing the back plate

A. Installing the surface closer

Tools recommended

Drill Bits

Metal: No. 21 & 10-32 Tap

Wood: 9/64"

Installing the surface closer

NOTE: Orient pinion (1) closest to hinge.

NOTE: Make sure arrows on

plate point upward.

3.1 Attach the main arm (1) to the top pinion with an

M6x20 socket head cap screw (2) using an M5 hex key.

Be sure the main arm is parallel to the door during

application.

#0 Phillips screwdriver

#2 Phillips screwdriver

3/16" flathead screwdriver

M2.5 & M5 Hex key

2.1 Attach the closer body (2) to the plate using the four

screws provided with the plate itself.

Right hand door

Toward the

hinge

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]

08279221 06/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

TS93 T/TH

—

5.1 Align the arm (1) with the slide shoe of the track channel. 5.2 Attach with one M8x15mm shoulder bolt (2) using an M5

hex key.

4.1 Position the individual components inside the track

channel and screw down each fitting.

NOTE: For TH ONLY - orient the hold open mechanism as

seen in the image above. Hold open mechanism and

hold open slide shoe must be installed with the arrows

pointing away from the hinges.

4.2 Attach the track channel (1) to the frame through the

end blocks with two flathead Phillips screws (2).

Right hand door - No hold open

Right hand door - With hold open

Left hand door - No hold open

Left hand door - With hold open

A. End block

B. Dead stop adjustable anchor

C. Cushion

D. Cushion protector

E. Hold open mechanism

F. Track channel

G. Slide shoe

H. Hold open slide shoe

A BC

Hinge

Part No.: TH KIT 93 ONLY

Closer is omitted in image for better

viewing of the track assembly.

Right hand door

HINGE

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]

08279221 06/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

TS93 T/TH

—

B. Adjustments

Adjusting the closing speeds: sweep, latch or backcheck and delayed actions

Confirm closer spring size prior to making any closing

speed adjustments.

Do not back valves out beyond closer casting.

Door should close in 3 to 6 seconds from 90º.

Maximum opening angle is 175º.

1.1 Adjust the sweep speed (1) for the area from 70° - 0°

Increase sweep speed: Turn valve counter-clockwise

Decrease sweep speed: Turn valve clockwise.

1.2 Adjust the latch speed (2) for the area from 7° - 0°.

Increase latch speed: Turn valve counter-clockwise

1.3 Adjust the backcheck (3) for the area from 65° - 175°.

Increase resistance: Turn valve clockwise

Decrease resistance: Turn valve counter-clockwise.

1.4 Adjust the delayed action (4) for the area from

180° - 70°.

Increase delayed action: Turn valve clockwise

Decrease delayed action: Turn valve counter-clockwise

1 [Sweep] 2 [Latch]

3 [Backcheck]

Sweep

Latch

Backcheck

Delayed action

4 [Delayed action]

Adjusting the spring force

TS9315

NOTE: Supplied with a size 2 spring setting.

Barrier free openings: Take an opening force reading from the

pull on the door. If required, adjust the spring force to meet

the barrier-free requirement.

Decrease force: turn counter-clockwise 5 times (max)

Increase force: turn clockwise 12 times (max)

Depending on opening conditions, a door adjusted to meet

barrier-free forces may not have sufficient power to reliably

close and latch the door.

TS9356

NOTE: Supplied with a size 6 spring setting.

Increase force: turn clockwise 6 times (max)

TS9315

DOOR WIDTH FULL TURNS OF

SPRING ADJUSTER

CLOSER

SIZE

INT. EX T.

2'6" ----- 0 2

3' 2'6" +3 3

3'6" 3' +9 4

4' 3'6" +12 5

TS9356 4' 3'6" -4 5

4'6" 4' 0 6

Non-barrier-free openings: ULC labeled units ONLY

CLOSER

TYPE

MAX DOOR

WEIGHT (LBS)

SPRING

SIZE

FULL TURNS OF

SPRING ADJUSTER

TS9315

100 2 0

125 3 +3

150 4 +9

200 5 +12

TS9356 200 5 -4

250 6 0

Increase

Decrease

Do not close valves completely.

Increase

Decrease

Increase Backcheck &

Delayed actions

Sweep & Latch

Speed

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarch[email protected]

08279221 06/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

TS93 T/TH

—

1.1 Snap both end covers (1) into place.

1.2 Remove the un-needed tab (2), and snap the closer body

cover (3) into place.

C. Installing the closer covers

Installing the covers

1.3 Attach with a 4-40 Phillips pan head screw (4) .

1.4 Snap the track cover (5) into place.

Adjusting the optional hold open

3.1 Slide the hold open mechanism (1) to the desired

location inside the track, to hold the door open to the

desired degree.

NOTE: Reference Section A, step #4 for hold open mechanism

location dependent upon door swing.

3.2 Using an M2.5 hex key, tighten the set screw (2) to

secure the hold open mechanism.

3.3 To adjust the force of the hold open force, engage the

hold open feature by opening the door and allowing the

hold open slide shoe (3) to slide over top of the hold open

mechanism and click into place.

3.4 Inside the M8x15mm hex screw (4) is a 2.5mm set

screw. To adjust the hold open force, use an M2.5 hex

key and turn the set screw:

Clockwise = increase force

Counter clockwise = decrease force

2.5mm set screw

(inside the M8x15 hex screw)

08279221

06/2014, Subject to change without notice

DORMA USA, INC.

DORMA DRIVE, DRAWER AC

REAMSTOWN, PA 17567

TOLL-FREE: 800-523-8483

FAX: 800-274-9724

E-MAIL: DORMAARCHITE[email protected]

WWW.DORMA-USA.COM

This manual suits for next models

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual