Dorma 8916 TDE User manual

PAGE

INS NO. Rev.

08279351 09/09

1 of 3

(4)

8916 / 8956 TDE, TDEH

TRACK DOUBLE EGRESS - PULL SIDE MOUNT

AND ACCESSORY PLATE BP89

WOOD FRAME

METAL FRAME

QTY

(4)

HOLD OPEN MECHANISM

(LH DOOR)

as shown. Arrow on plate to point toward arm

(RH DOOR)

BP89 Plate applications only. Attach plate to door

attachment.

QTY

(4)

QTY

METAL FRAMES

QTY

(4)

WOOD FRAMES

PLATE

(LEFT HAND DOOR)(RIGHT HAND DOOR)

HINGES

CHINGESC

Attach closer to door or plate with sweep and

latch valves facing hinges.

according to appropriate template.

Determine hand of door. Prepare door and frame

(REFERENCE UNIT CARTON FOR ACCESSORIES AND

OPTIONS SUPPLIED)

LISTINGS.

IDENTIFIED IN THE INDIVIDUAL DOOR MANUFACTURER'S

DOORS, UNLESS AN ALTERNATIVE METHOD IS

WOOD OR PLASTIC FACED COMPOSITE TYPE FIRE

OF COMPONENTS TO UNREINFORCED DOORS AND TO

CAUTION: SEX NUTS ARE REQUIRED FOR ATTACHMENT

REVERSE BEVEL

RIGHT HAND DOOR

LEFT HAND DOOR

REVERSE BEVEL

RIGHT HAND LEFT HAND

(WOOD)

(METAL)

(2)

QTY

(2)

QTY

L HINGES

M6 HEX KEY

ARM TO SLIDE SHOE

(1)

QTY

END BLOCK

L HINGES

(TDEH UNITS ONLY)

SLIDE SHOE

RUBBER STOP

SLIDE SHOE

into track and attach track to frame.

(TDE UNITS ONLY)

NOTE: (A) MOUNTING SCREWS PASS THROUGH END

(B) RIGHT HAND SHOWN.

Insert slide shoe, rubber stop and end blocks

END BLOCK

Assemble track and attach to frame.

BLOCKS.

RUBBER STOP

stop, hold open mechanism, and end blocks into

and tighten securely. Insert slide shoe, rubber

Attach arm to slide shoe using screw supplied

track and attach track to frame.

IMPORTANT : L HINGE

NOTE: HOLD OPEN MECHANISM AND SLIDE SHOE MUST

BE INSTALLED WITH ARROWS POINTING AWAY

FROM THE DOOR HINGES. (ARROWS ARE

STAMPED ON SLIDE SHOE & HOLD OPEN

MECHANISM)

INSPK 08279350 Rev.09/09

control when extra time is required to pass through

Adjust sweep and latch valves.

Closing time from 90° to 15° (sweep range) is

generally adjusted to take a minimum of 3 seconds.

Closing time from 15° to fully closed (latch range)

should take a minimum of 1.5 seconds.

INCREASE

DECREASE

hex key.

INCREASE

the door. All valve adjustments are made with a 3/32"

Optional delayed action offers additional closing speed

DECREASE

CAUTION: DO NOT REMOVE VALVES.

NOTE: DELAYED ACTION IS AN OPTIONAL FEATURE.

RANGE

SWEEP

LATCH

RANGE

(INTENSITY)

BACKCHECK

POSITIONING VALVE

SWEEP & LATCH

DELAYED

ACTION

(TIME)

RANGE

LATCH

(SPEED)

SWEEP (SPEED)

BACKCHECK RANGE

DELAYED ACTION

BACKCHECK OR DELAYED ACTION

5Install main arm

onto top pinion. Fasten securely with pinion

With main arm parallel to door, place main arm

Rotate pinion 45° AWAY FROM HINGE edge of door.

Place wrench on bottom

pinion.

Adjust according to chart.

ADJUSTER

FULL TURNS

OF SPRING

+12

FULL TURNS

OF SPRING

ADJUSTING NUT

ADJUST SPRING TENSION ACCORDING TO THE FOLLOWING CHART.

8916

8956

CLOSER

ULC LABELED UNITS ONLY

TYPE

200

200 6

SIZE

SPRING

DOOR

WEIGHT

150

125

MAX.

NON-BARRIER-FREE OPENINGS -

TYPE

8916

8956

CLOSER

INTERIOR

2'-6"

3'-6"

3'-0"

4'-0"

+12

DOOR WIDTH

SPRING

SIZE

Take an opening force reading from

the pull on the door. If required, adjust the spring tension

to meet the barrier-free requirement. Maximum number of

adjusted to meet barrier-free forces may not have sufficient

power to reliably close and latch the door.

turns counter clockwise=8. Maximum number of turns

clockwise =14. Depending on opening conditions, a door

BARRIER-FREE OPENINGS -

8916 ONLY ADJUSTER

Adjust spring tension, if required, using a 1/4" wrench.

8956 supplied with size 6 setting.

8916 supplied with size 4 spring setting.

SPRING TENSION

CRITICAL

NOTE:

3'-6" +6 6+

250

LEFT HAND IS A MIRROR IMAGE.

INSTALLATION SHOWN.

NOTE: RIGHT HAND DOOR

PINION SCREW

PINION

6mm HEX KEY

L HINGE

45°

ROTATE

PINION 45°

Main Arm

(1)

QTY

08279351 2 of 3 09/09

INS NO. PAGE Rev.

Place tab in cover slot opposite main arm.

(2)

QTY

Place cover over closer and fasten securely with

screws provided.

NOTE: LEFT HAND INSTALLATION SHOWN. RIGHT

TAB

HAND IS A MIRROR IMAGE.

M2.5 HEX KEY

SNAP VALVE ADJUSTMENT

WRENCH INSIDE COVER

To enable hold open,

push the white slide into

the hold open mechanism.

To disable hold open,

pull the white slide away

from hold open mechanism.

M2.5 HEX KEY

weaken force.

To adjust hold open

force, turn clockwise to

increase force, and

counter clockwise to

Set hold open.

OFF

(HOLD OPEN UNITS ONLY)

Place the hold open

mechanism in desired

position and tighten screw.

08279351 3 of 3 09/09

INS NO. PAGE Rev.

This manual suits for next models

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual