Dimplex ENG56-400 User manual

The product complies with the European Safety Standards and the European Standard Electromagnetic Compatibility (EMC)

These cover the essential requirements of EEC Directives

Pro Range

ENG56-400, ENG68-400, ENG56-600

EN: This product is only suitable for well insulated rooms or occasional use. DE: Dieses Produkt ist nur für gut isolierte Bereiche oder

gelegentliche Verwendung geeignet. FR: Ce produit convient uniquement à des endroits bien isolés ou pour un usage occasionnel.

IT: Questo prodotto è adatto solo per spazi ben isolati o per uso occasionale. ES: Este producto sólo es adecuado para espacios

bien aislados o un uso ocasional. NL: Dit product is uitsluitend geschikt voor goed geïsoleerde ruimten of voor sporadisch gebruik.

PL: Produkt ten jest odpowiedni wyłącznie do dobrze odizolowanych miejsc lub do okazjonalnego użytku. NO: Dette produktet egner seg kun for godt

isolerte rom eller sporadisk bruk. RO: Acest produs este adecvat exclusiv spaţiilor bine ventilate sau utilizării ocazionale. CZ: Tento výrobek je vhodný

pouze do dobře izolovaných prostor nebo k příležitostnému použití. DK: Dette produkt er kun egnet til velisolerede rum eller lejlighedsvis brug. PT: Este

produto somente é adequado para espaços bem isolados ou uso ocasional. SE: Denna produkt är endast avsedd för välisolerade utrymmen eller tillfällig

användning. FI: Tämä tuote soveltuu ainoastaan hyvin eristettyihin tiloihin tai satunnaiseen käyttöön. SK: Tento výrobok je vhodný len pre dobre izolované

priestory alebo na občasné použitie. SI: Ta izdelek je primeren le za dobro izolirane prostore ali za občasno uporabo. HR: Ovaj proizvod je pogodan samo

za dobro izolirane prostore ili povremenu upotrebu. HU: Ez a termék csak jól szigetelt terekhez vagy eseti használatra alkalmas

08/53884/0 ISSUE 6 OCN 11777

UK ................................................................................................ 1

DE .............................................................................................. 10

NL ............................................................................................... 20

FR ............................................................................................... 29

IT ................................................................................................ 38

ES ............................................................................................... 48

ENG56-400, ENG68-400, ENG56-600

Introduction

Please read this information guide carefully to be able to safely install, use and maintain your product.

Important Safety Advice

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR

DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

Important Safety Advice

When using electrical appliances, basic precautions should always be followed to reduce the risk

of re, electrical shock and injury to persons, including the following:

If the appliance is damaged, check with the supplier before installation and operation.

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower or swimming pool.

Do not locate the appliance immediately below a xed socket outlet or connection box.

Warning: This heater must not be used for anything other than normal domestic household

purposes in the country where it was purchased from a recognised commercial retailer.

This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by Children without supervision.

Children of less than 3 years should be kept away unless continuously supervised. Children aged

from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been

placed or installed in its intended normal operating position and they have been given supervision or

instruction concerning use of the appliance in a safe way and understanding the hazards involved.

Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance

or perform user maintenance.

Warning: This appliance must be earthed.

The use of an extension lead or multi-plug adaptor is not advised when connecting this product to

the mains. Connection through these devices could lead to a risk of overloading, overheating and

even re at the extension lead or adaptor due to inadequate connection quality.

This heater must be used on an ~alternating current supply (~) only and the voltage marked on the

heater must correspond to the supply voltage.

Do not use this appliance in series with a thermal control, a program controller, a timer or any

other device that switches on the heat automatically, since a re risk exists when the appliance is

accidentally covered or displaced.

DO NOT use the heater on deep pile carpets or the long hair type of rugs, or less than 750mm

(30”) away from any overhanging surface. Keep combustible materials such as drapes and other

furnishings clear from the front, sides and rear of the heater. Do not use heater to dry your laundry.

In the event of a fault unplug the appliance. Unplug the appliance when not required for long

periods.

The appliance must be positioned so that the plug is accessible. If the supply cord is damaged it

must be replaced by the manufacturer or service agent or a similarly qualied person in order to

avoid a hazard. Keep the supply cord away from the front of the appliance.

Installation Instructions

This section describes how to set up your re.

BEFORE YOU START

1. Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible future use

e.g. in the event of moving house or returning the appliance to your supplier.

2. Before connecting the appliance, check that the supply voltage is the same as that stated on the heater.

Installation into a Fireplace Mantle

1. When installing this appliance into a replace mantle please ensure that you choose a mantle suitable for your appliance

(Fig 18). There is to be an air vent at the front of the replace mantle of at least 88cm2. It is essential to ensure that air

can circulate into the appliance – otherwise the Opti-myst ame effect willnotoperate correctly. This pathway for air must

not be obstructed

2. Remove the 4 spacing brackets on the front of the appliance (Fig 19)

General Information

Only use ltered water in this appliance.

Always ensure that the appliance is sitting on a level surface.

Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair

type of rugs.

Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is

related to the operation of the ame effect. This is normal and should not be a cause for concern.

If this product experiences a power surge for whatever reason the product may cut-out. This is a normal safety feature and

the product will resume operation after 30 seconds.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.

If you intend not using the appliance for longer than a week, drain the water from sump and water tank and dry the sump.

The water tank, sump, sump lid, tank cap and air lters must be cleaned once every week, particularly in hard water areas.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under ‘Maintenance’ and ‘Changing lamps’.

Caution: Some parts of this product can become very hot and cause burns. Particular attention

has to be given where children and vulnerable people are present.

Warning: In order to avoid overheating, do not cover the appliance. Do not place material or

garments on the appliance, or obstruct the air circulation around the appliance, for instance by

curtains or furniture, as this could cause overheating and a re risk.

The appliance carries a DO NOT COVER warning

Warning: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance

must not be supplied through an external switching device, such as a timer, or connected to a

circuit that is regularly switched on and off by the utility.

Technical Information

Model No: ENG56-400 E, ENG68-400 E, ENG56-600 E

Heat Output

230V 240V

Nominal Heat Output

PNom 1.8 2.0 kW

Minimum Heat Output

Pmin 0.9 1.0 kW

Maximum Continuous Heat Output

Pmax 1.8 2.0 kW

Auxiliary Electricity Consumption

In Standby Mode PNom 0.45 0.48 W

electronic room temperature control plus week timer

Operating the Product

3. Slide the appliance into the replace mantle fully from the back ensuring that it is sitting in the center of the mantle. Using

suitable screws (not supplied) screw x the appliance in place (Fig 20)

4. Be sure to position the replace within 1m of a power outlet (Fig 21)

Installation into a wall or recess cavity

1. Note the product dimensions in Fig 1 and build a suitable structure for the appliance to t into within 1m of a power outlet

(Fig 22). Using suitable screws (not supplied) screw x the appliance in place

2. Note the venting slots in the appliance. There are located at the front base and under the appliance

3. Build the wall up against the appliance using the spacing brackets as a guide.

4. There is to be an air vent at the front of the structure of at least 88cm2. It is essential to ensure that air can circulate

into the appliance – otherwise the Opti-myst ame effect will not operate correctly. This pathway for air must not be

obstructed. For examples of air vents in a wall or recess cavity see Fig 23

Connecting the Transducer Unit + Lamps

1. Release the two red tabs by turning them by 90 degrees (Fig 2)

2. Lift out the Sump Nozzle (Fig 3)

3. Insert lamps into lamp holders (Fig 4), carefully locating the pins into the holes (Fig 4a)

4. Push lamps rmly into place

5. Place the Transducer Unit into the sump and join the cable to the connector on the sump (Fig 5)

6. To ensure that the Transducer Unit is correctly placed in the sump, the tab on the Transducer Unit should be lined up with

the moulded recess in the sump (Fig 5a).

7. Ensure that the cable is not placed above the disc on the Transducer Unit (Fig 5b). To prevent the cable becoming

pinched between the nozzle and the sump, place the cable in the slot in the wall of the sump.

8. Replace the Sump Nozzle and secure it by turning the two red tabs by 90 degrees (Fig 6)

Filling the Water Tank

9. Place Water Tank in sink and remove cap (turn anti-clockwise to open) (Fig 7)

10. Fill Water Tank with ltered tap water only. This is necessary to prolong the life of the ame and smoke producing unit.

The water should be ltered through a conventional domestic water lter unit and the lter shouldbe replaced regularly.

Distilled water must not be used.

11. Screw the cap back on – do not overtighten.

12. Place the Water Tank in the Sump, with the tank cap facing down and the at side of the tank facing outward (Fig 8)

Assembling the re

13. Place the Fuelbed on top of the Water Tank and Mist Nozzle (Fig 9)

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY AND/OR DAMAGE.

Manual Controls

The Opti-myst Manual controls are located on the base of the appliance.

(See Fig. 10 for Manual Control layout)

Switch ‘A’:- Controls the electricity supply to the Fire.

Note: This switch must be in the ‘ON’ (I) position for the Fire to operate with or without heat when activated.

Switch ‘B’:- Press once to turn on the ame effect. This will be indicated by an audible “beep”. Although the main lights

operate immediately it will take a further 45 seconds before the ame effect starts.

Press to put re into standby mode. This will be indicated by one “beep”.

Remote Control

The remote control is packed with 2 AA batteries in a bag. Lift off the battery cover on the back of the remote control and

insert the batteries taking note of the polarity.

The remote control has already been paired to your product during factory assembly. In the unlikely event that the remote

control disconnects from the product, or you obtain a spare remote control, you will need to complete the pairing pro-

cess:

1. With the product plugged in press switch A to the ON (I) position. You should hear an audible beep

2. Press and hold ‘Button 6’ until PAIR appears on the display

3. Bring the remote control close to the product where the receiver is . See Fig 17

4. The product will start to beep and blink

5. Press ‘Button 6’ to complete the pairing process. The product will go into standby mode.

Switching on the appliance

Press and hold the ENTER button for 3 seconds to activate the remote control. FIRE will be displayed and ON will be

blinking. Press ENTER to swtich ON the appliance. The lamps light up and the ame effect sets in after approx. 45 seconds.

Adjust the Flame Setting

With the remote control activated. FIRE will be displayed and OFF ashes on the display. Press UP button until FIRE symbol

ashes. Press ENTER. The current ame setting will be displayed F1-F6. Press the UP and DOWN buttons to adjust the

setting, product beep once selection is been made. After you have selected your ame setting press BACK to exit the menu

and return to the home screen.

Select the Heater Setting

You have the option of setting the heating high (HI), low (LO) or completely interrupting heating (OFF). Connect the remote

control to the device if you have not already done so. Use the UP and DOWN buttons to navigate to the symbol ashes.

Press the ENTER key 21°C is displayed on the screen and OFF ashes, heating starts. Then press and hold the ADV

button until HI/LO or OFF appears (the respective default setting ashes). Use UP and DOWN buttons to select the setting

you want. Conrm your setting with the ENTER key. The screen goes back and 21°C is displayed OFF ashes. If you now

conrm OFF with the enter key, the heating switches off and the screen goes back to the home screen.

NOTE: With the OFF setting, heating is completely switched off and cannot be started using the hand setting. If heating is

required, we recommend the setting LO or HI.

Setting the Thermostat

With the remote control activated.

Navigate with the up / down buttons to the hand symbol . The hand symbol ashes.

Press the ENTER key 21°C appears and the heating starts, OFF ashes. However, this only applies if the presetting LO or

HI has been made before. The heating operation runs until the room temperature of 21°C is reached. With the up / down

buttons you can adjust your desired temperature if necessary. If you choose to switch off the heating operation you can

interrupt the heating by pressing ENTER button while OFF ashing. The program then goes back to home screen.

Thermal Safety Cut-out

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if the heat

outlet was restricted in any way. If the cut-out operates, unplug the heater from the socket outlet and allow approximately

10 minutes before reconnecting. Before switching the heater back on remove any obstruction that may be restricting the

heat outlet, then continue normal operation.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied

through an external switching device, such as a timer, or connected to a switch that is regularly switched on and off by the

utility.

Setting the Date and Time

To set the date and time on the heater; with the remote control activated navigate UP/DOWN button to Date & Time icon

1. Press Enter when the is blinking

2. Press < and > to set the Hour, press Enter

3. Press < and > to set the Minutes, press Enter to conrm the time

4. Press < and > to set the Day, press Enter

5. Press < and > to set the Month, press Enter

6. Press < and > to set the Year, press Enter to conrm the year

7. Press < and > to select ON/OFF for the Daylight saving time, press Enter to conrm and returns to home screen.

Modes of Remote Operation

User Timer : Provides greatest exibility to the user. Four times slots are available throughout the day and these can be

customised for each day of the week. See “How to adjust the timer modes” for instructions on adjusting these from the

factory default time periods & temperatures.

Manual Mode : This mode heats the room to the temperature you have set the remote control to.

Frost Protection : This mode will maintain a room temperature to 7°C. This mode should be used to provide protection

against frost as indicated by the frost icon.

Choosing and Setting a User timer Mode

User Timer - To re-programme the factory default Timer Modes: with the remote control activated, navigate UP/DOWN

button to user timer

1. Press Enter when is blinking

2. Press > Once EDIT icon blinks then press Enter

*Days of the weeks are now displayed at the top of the screen*

Day 1 = Monday

Day 2 = Tuesday

Day 3 = Wednesday

Day 4 = Thursday

Day 5 = Friday

Day 6 = Saturday

Day 7 = Sunday

4. Press > to navigate to the desired day and Press Enter to Select

5. P1 will be displayed on screen

6. Press Enter to select P1,or to navigate to P2, P3 or P4 press > and press Enter to select

7. ON will be displayed

8. Press < or > to adjust the ON Hour time, press Enter to Conrm

9. Press < or > to adjust the ON Minute time, press Enter to Conrm

10. Press < or > to adjust the Temperature setting, press Enter to Conrm10. Press < or > to adjust the Temperature setting, press Enter to Conrm

11. OFF will be displayed11. OFF will be displayed

12. Press < or > to adjust the OFF Hour time, press Enter to Conrm

13. Press < or > to adjust the OFF Minute time, press Enter to Conrm

Press Enter to modify Programme P2, follow steps 5-12, Press > to skip to P3

Press Enter to modify Programme P3, follow steps 5-12, Press > to Skip to P4

Press Enter to modify Programme P4, follow steps 5-12

To copy newly programmed P1-P4 heating programmes to other days, press and hold ADV button COPY will be

displayed then navigate UP/DOWN buttons to other days, while the day ashing press and hold ENTER button to paste,

PASTE will be displayed to conrm the setting.

Press BACK button user timer screen is displayed, navigate UP/DOWN button to ash ON and press ENTER to conrm

the user timer setting. During this setting product will turn off and turn on for the time you selected.

To turn of the User timer, activate the remote control, OFF ashes. Press ENTER to conrm.

Getting the Desired Flame Effect

1. With the remote control activated, OFF on the display will be ashing, navigate UP button to ash FIRE and press

ENTER. The current setting will be displayed. Press < or > to toggle between F1 and F6. F1 being the lowest setting

and F6 being the highest setting.

2. Generally the ames appear more realistic when the ame control is turned down.

3. Give the ame generator time to react to changes you may make.

4. The re will use less water if the ame effect is set to a lower level.

5. Do not tilt or move the re while there is water in the tank or sump.

6. Make sure that the re is on a level oor.

Customising the display

The maximum temperature set point on the product is 30°C You have the option to reduce this set point. You can also

change °C to °F

1. Press the Menu button.

2. Press < or > to navigate to symbol ashes.

3. Press Enter to conrm.

4. Press and hold MENU button until °C and °F. displayed

5. Press < or > to select between °C and °F. Press ENTER to conrm.

6. Press < or > to choose your maximum temperature set point.

7. Press BACK button to return to the home screen.

Manual Mode - To choose a constant heat mode. This mode ignores the User Timer and maintains the displayed

temperature.

• Press Menu Button

• Press < or > to highlight the Hand icon

• Press Enter to Conrm

• Use < and > to adjust to the desired temperature

Frost protect - Frost protect mode maintains a room temperature of 7°C throughout a 24 hour period. This mode should

be used to provide protection against frost as indicated by the Frost icon.

• Press the Menu button

• Press < or > to highlight the snowake icon

• Press Enter to conrm

• Press < or > to exit this mode and enter manual mode.

GENERAL TIPS

Only use ltered tap water in this appliance.

Always ensure that the appliance is sitting on a level surface.

If you intend not using the appliance for longer than a week, remove and empty the sump and water tank.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under ‘Changing lamps’.

FILLING THE WATER TANK

When the water tank is empty, the ame and smoke effect shuts off and you will hear 2 audible beeps, follow these steps.

1. Press Switch ‘A’ to (0) (Fig. 10)

2. Gently lift out the fuelbed and carefully set aside.

3. Remove the water tank by lifting upwards and outwards.

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (Fig. 7)

5. Fill tank with ltered tap water only. This is necessary to prolong the life of the ame and smoke producing unit.

The water should be ltered through a conventional domestic water lter unit and the lter should be replaced regularly.

6. Screw the cap back on, do not over tighten.

7. Return the tank to the sump, with the tank cap facing down and the at side of the tank facing outward. (Fig. 8)

8. Gently place the fuelbed back into position. (Fig. 9)

9. Press Switch ‘A’ to ‘ON’ (I) position (Fig. 10)

CHANGING LAMPS

If the ame and smoke effect appears grey or colourless it may be that one or more lamps have failed.

You can check for lamp failure as follows.

1. Leaving the ame effect on, lift out the fuelbed and water tank.

2. It should be possible to view the lamps with the nozzle in place and observe which one needs to be changed.

Maintenance

Remote Control

1Display Screen

2‘Menu’ Button

3‘Back’ Button

4‘Advance’ Button

5‘Up and Down’ Arrows

6‘Enter’ Button

3 4

Adaptive Start

The built-in electronics in this appliance have a learning function with regards to how long it takes to heat up a room. Having

learnt how quickly it can heat up your room, the appliance is able to turn on at just the right time in order to get the room

up to a comfortable temperature when you want it. For example, if you get up at 7am, you would normally have to guess

when to turn the heating on in order for it to pre-heat the room in time. Depending on how cold it is outside, this could mean

the room is still cold when you have to get out of bed, or mean that its been warm for half an hour before it needed to be.

Adaptive Start means that if you select 21°C at 7am, the heater will turn on exactly when it needs to in order to meet this

target, running for shorter periods of time when the weather is mild, and ensuring the room is nice and warm in the winter.

The Adaptive Start function will automatically activate when you use the Timer Mode.

AFTER SALES SERVICE

Your product is guaranteed for two years from the date of purchase. Within this period, we undertake to repair or

exchange this product free of charge (excluding lamps & subject to availability) provided it has been installed and operated

in accordance with these instructions. Your rights under this guarantee are additional to your statutory rights, which in turn

are not affected by this guarantee.

RECYCLING

For electrical products sold within the European Community - At the end of the electrical products useful life

it not be disposed of with household waste. Please recycle where facilities exist. Check with your Local

Authority or retailer for recycling advice in your country.

Additional Information

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the re from the mains.

4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.

5. Remove the sump as described in the Cleaning Section.

6. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder,

(Fig. 4 and 4a).

Replace with an OPTIMYST, 12V, 45W, Gu5.3 base, 8° beam angle, coloured lamp. (Purchased from our your

supplier)

7. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push rmly in place.

(Fig. 4 and 4a).

8. Replace the sump, nozzle, water tank and fuelbed.

CLEANING

Warning – Always press Switch ‘A’ to the ‘OFF’ (0) position (Fig. 10) and disconnect from the power supply before

cleaning the re.

We recommend cleaning the following components once every week, particularly in hard water areas:-

Water Tank, Sump, Nozzle, Tank cap and seal, Air lter.

For general cleaning use a soft clean duster – never use abrasive cleaners.

To remove any accumulation of dust or uff the soft brush attachment of a vacuum cleaner should occasionally be used to

clean the outlet grille of the fan heater.

Water tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the

outer groove and the centre rubber seal.

3. Put a small quantity of washing up liquid into the tank, ret the cap and shake well, rinse out until all traces of washing

up liquid are gone.

4. Rell with ltered tap water only, replace the cap, do not overtighten.

Sump

1. Press Switch ‘A’ to the ‘OFF’ (0) position

2. Gently lift out the fuelbed and place carefully on the ground.

3. Remove the water tank by lifting upwards.

4. Disconnect the electrical connector, located on the right side of the sump. (Fig. 5) .

5. Release the right sump locking tabs by turning 90°. This allows the sump to be lifted completely from its location. (Fig.

11)

6. Gently lift up the sump, taking care to keep level so as not to spill any water. Sit the assembly in the sink.

7. Release the left sump locking tabs by turning 90°, then lift off the Nozzle. (Fig. 3)

8. Lift out the transducer and carefully tilt, as shown, so that the liquid drains out of the sump. (Fig. 13)

9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces in the

sump and gently clean the transducer including the metal discs located in the top grooved surface. (Fig. 14)

10. When cleaned, thoroughly rinse the sump with clean water to remove all traces of washing up liquid.

11. Clean the Nozzle with the brush and ush out thoroughly with water. (Fig. 15)

12. Reverse the above steps to reassemble.

Air lter

1. Gently lift out the fuelbed and place carefully on the ground.

2. Gently slide the air lter upwards out of its plastic holder. (Fig. 16)

3. Gently rinse with water in the sink and dry with fabric towel before returning.

4. Replace the lter making sure that the coarse black lter is facing the front of the re.

5. Replace the fuelbed.

Other manuals for ENG56-400

This manual suits for next models

Table of contents

Languages:

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex DF2608 User manual

Dimplex

Dimplex DFB4047 User manual

Dimplex

Dimplex Featherston GDS26L5-1152LR User manual

Dimplex

Dimplex MULTIFIRE DF3215 User manual

Dimplex

Dimplex MULTIFIRE DF3015 User manual

Dimplex

Dimplex EWM-COPPER User manual

Dimplex

Dimplex DNV20CH Manual

Dimplex

Dimplex DFB4047 User manual

Dimplex

Dimplex ELBA User manual

Dimplex

Dimplex 6908760100 User manual

Dimplex

Dimplex Pro Series User manual

Dimplex

Dimplex Revillusion RBF30 User manual

Dimplex

Dimplex GDS23L8-1904GB User manual

Dimplex

Dimplex DMCS13R User manual

Dimplex

Dimplex ELTHAM ETM20-AU User manual

Dimplex

Dimplex DFP6975O User manual

Dimplex

Dimplex Opti-V User manual

Dimplex

Dimplex EXBURY EBY15 User manual

Dimplex

Dimplex SILVERTON User manual

Dimplex

Dimplex SIL48 User manual

Dimplex

Dimplex Revillusion RBF30-FG User manual

Dimplex

Dimplex TOLUCA DELUXE-EU User manual

Dimplex

Dimplex EF3003 User manual

Dimplex

Dimplex BF45DXP User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual