Dimplex BF33STP User manual

Installation Guide

Model

BF33STP/DXP

BF39STP/DXP

BF45DXP

IMPORTANT SAFETY INFORMATION: Always read this manual ﬁrst before attempting to install or use this ﬁreplace. For your

safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property

damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

7206350500R08

2www.dimplex.com

Listing and Code Approvals.................................................................3

Model Speciﬁcations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step-by-Step Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section A: Installation information ...........................................................4

Framing Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Mounting Flanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Section B: General Electrical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Recommended Power Supply Wire Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Voltage Selector Switch Location ............................................................5

Section C: Direct Power Wiring ..............................................................6

240V Installation .........................................................................6

120V Installation .........................................................................6

120V Installation - No Heat Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Section D: Alternate Control Options .........................................................8

240V Main Power Wall Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

120V Main Power Wall Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

120V Main Power Wall Switch - No Heat .....................................................10

120V/240V Heater Wall Switch Control ......................................................11

120V/240V Wall Mounted Thermostat .......................................................12

120V/240V Wall Mounted Flame Override Switch ..............................................13

Wall Remote - WRCPF-KIT ...............................................................14

Unit Internal Wiring Diagram ...............................................................14

!NOTE: Procedures and techniques that are consid-

ered important enough to emphasize.

CAUTION: Procedures and techniques which, if not

carefully followed, will result in damage to the equipment.

WARNING: Procedures and techniques which, if not

carefully followed, will expose the user to the risk of

ﬁre, serious injury, or death.

Table of Contents

The BF series ﬁreplaces have been tested in accordance with the UL 2021 and CSA C22.2 No. 46 standards for ﬁxed and

location-dedicated electric room heaters.

Model

Number Description Voltage

Rated

Power

(Watts)

Remote

Control

Wall

Thermostat

Refractory

Brick Look

Current Draw (Amps)

No Heat

120V 120V 208V 240V

BF45DXP 45" Deluxe

120/120/

208/240

245/1440/

2100/2700 Optional Optional

Included 2.0 12.0 10.10 11.25

BF39DXP 39" Deluxe Included 2.0 12.0 10.10 11.25

BF39STP 39" Standard N/A 2.0 12.0 10.10 11.25

BF33DXP 33" Deluxe Included 2.0 12.0 10.10 11.25

BF33STP 33" Standard N/A 2.0 12.0 10.10 11.25

!NOTE: Power ratings shown include the light bulbs and motors (275 watts)

The installation of the fireplace unit must comply with the applicable Local and/or National Electrical Codes and utility require-

ments. This installation should be entrusted to duly qualified personnel where required by law.

MODEL SPECIFICATIONS

LISTING AND CODE APPROVALS

!NOTE: Please read all instructions before installing.

1. Rough in framing opening following the recommended dimensions located in Section A: Framing Dimensions.

2. Allow 8" (20.3 cm) of service cable for connecting power supply wire to junction box on ﬁreplace when installing before

ﬁnishing wall. Allow up to 4' (121.9 cm) of service cable for connecting power supply wire to junction box on ﬁreplace

when installing after ﬁnishing wall. Remove the outer jacket and strip the individual conductors ½" (1.3 cm) from the end.

3. Loosen the screw securing the junction box cover and remove the cover.

4. Remove knockouts, if necessary, or use the provided cable clamp.

5. Place unit in position in the framed opening, level with shims if necessary and attach unit to frame using mounting ﬂanges

provided (Figure 2).

6. Unit is factory wired for 208/240V power supply. If 120V operation is required, slide the switch and reconﬁgure the wiring

(Section C). Wires L1, L2, N & G are attached to the rear of the junction box cable clamp for easy access.

!NOTE: If wiring unit to operate with NO heat a dedicated circuit may not be required.

7. Wire a dedicated, properly fused circuit with a 15amp rating for the appropriate voltage (120V, 208/240V). See Section C

for factory setting wiring.

8. Make wall switch and or wall mounted thermostat connections as outlined in Section D.

9. Place all connectors inside the unit and secure the junction box cover to unit. Ensure that the cable clamp grips only the

jacket of service cable, thermostat and if applicable wall switch lines.

WARNING: Ensure method of installation does NOT obscure the air intake slots on bottom front of unit in any manner.

(See diagram in Section A)

STEP-BY-STEP INSTALLATION

4www.dimplex.com

FRAMING DIMENSIONS

Rough-In Framing Dimensions Firebox Dimensions Rough-In Corner Framing

This ﬁreplace is a zero clearance design, with the exception of the top of the unit, where any insulation and vapor barrier

should be placed a minimum of 2" (5.1 cm) from the unit. No combustibles can be placed on the top surface of the ﬁreplace.

CAUTION: Ensure installation does not allow ﬁreplace to be in direct contact with building vapor barrier or insulation and

meets all local building code.

Four mounting ﬂanges on the sides of the unit are provided to facilitate installation.

MOUNTING FLANGES

SECTION A: INSTALLATION INFORMATION

Figure 1

Figure 2

Model A B C D E F G H I J K L

BF45DXP 16.0"

(40.5cm)

45.5"

(115.6cm)

33.5"

(85.1cm)

30.1"

(76.5cm)

15.3"

(38.9cm)

42.0"

(106.7cm)

44.7"

(113.5cm)

22.8"

(57.9cm)

32.7"

(83.1cm)

60.0"

(152.4cm)

42.0"

(106.7cm)

42.0"

(106.7cm)

BF39STP/DXP 16.0"

(40.5cm)

39.5"

(100.3cm)

33.5"

(85.1cm)

30.1"

(76.5cm)

15.3"

(38.9cm)

36.0"

(91.4cm)

38.7"

(98.3cm)

22.8"

(57.9cm)

32.7"

(83.1cm)

54.0"

(137.2cm)

38.0"

(96.5cm)

38.0"

(96.5cm)

BF33STP/DXP 15.0"

(38.1cm)

33.5"

(85.1cm)

29.5"

(75.0cm)

25.7"

(65.3cm)

14.3"

(36.3cm)

29.6"

(75.2cm)

32.8"

(83.3cm)

18.8"

(47.8cm)

28.5"

(72.4cm)

48.0"

(121.9cm)

34.0"

(86.4cm)

34.0"

(86.4cm)

Air Intake Slots

There are two mounting ﬂanges located on each side of the ﬁreplace insert.

From the inside of the unit, bend tabs outward and mount to the inside of the framing using suitable hardware.

Mounting

Flanges

SECTION B: GENERAL ELECTRICAL INFORMATION

For 120V installations use two conductor, non-metallic sheath cable with ground wire (3 wires total) for the incoming power

supply on ﬁreplace inserts. Use the appropriate wire to meet local and national electrical codes for rated power consumption.

For 208V / 240V installations use three conductor, non-metallic sheath cable with ground wire (4 wires total) for the incom-

ing power supply on ﬁreplace inserts. Use the appropriate wire to meet local and national electrical codes for rated power

consumption.

Two conductor, non-metallic sheath cable with ground wire (3 wires total) is recommended for installation of a wall mounted

thermostat and/or wall switch for use on ﬁreplace inserts. Use appropriate wire to meet local and national electrical codes for

rated power consumption. All wire gauges should match the recommended wire sizes shown below.

Voltage Wire Gauge Fuse Rating

120 Volts 14 Gauge 15 Amp

208 Volts 14 Gauge 15 Amp

240 Volts 14 Gauge 15 Amp

RECOMMENDED POWER SUPPLY WIRE SPECIFICATIONS

!IMPORTANT: Ensure that the incoming power supply voltage matches the setting of the voltage selector switch.

!NOTE: The voltage selector switch is located inside the exhaust panel on the top right hand corner.

CAUTION: When changing the voltage selector switch from 240V to 120V ensure that the power supply is turned off.

!NOTE: Carefully insert a ﬂat headed screwdriver inside the exhaust panel to change the switch from 240V (230 position)

to 120V (115 position).

When wiring the unit for 208V / 240V the voltage selector switch should be in the 230V position.

When wiring the unit for 120V the voltage selector switch should be in the 115V position.

VOLTAGE SELECTOR SWITCH LOCATION

6www.dimplex.com

!IMPORTANT: The unit is factory conﬁgured for 208/240V operation.

!NOTE:

Use 3 conductor wires with ground (4 wires total) from the power supply (breaker panel) to the junction box on the unit.

!NOTE: All wiring must be completed prior to installing the unit.

!NOTE: Ensure that the voltage selector switch is in the proper position for the required supply voltage prior to connecting

the unit to the power supply.

1. Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit. Ensure that the

switch is in the 240V position. (230 is printed on switch)

2. Loosen the screw securing the junction box cover and remove the cover.

3. Remove the knockouts (if necessary) or use the provided cable clamp.

4. Pull out the four wires marked L1, L2, N, and G.

5. Connect L1 (black) from the unit to the L1 (black) from the power supply.

6. Connect L2 (red) from the unit to the L2 (red) from the power supply.

7. Connect N (white) from the unit to the to the Neutral (white) from the power supply.

8. Connect the ground wire (green) from the unit to the ground from the power supply.

9. Ensure that all connections are tight.

10. Insert all the wiring back into the unit and secure with a cable clamp.

240 V

POWER

SUPPLY

(BREAKER

PANEL)

FIR E P LAC E J UNC TION B OX

WHITE WIRE - N

RED WIRE – L2

BLACK WIRE – L1

GREEN WIRE - G

WHITE WIRE - N

RED WIRE – L2

BLACK WIRE – L1

GROUND WIRE - G

SECTION C: DIRECT POWER WIRING

240V INSTALLATION

!IMPORTANT: The unit is factory conﬁgured for 208/240V operation.

!NOTE:

Use 2 conductor wires with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit.

!NOTE: All wiring must be completed prior to installing the unit.

!NOTE: Ensure that the voltage selector switch is in the proper position for the required supply voltage prior to connecting

the unit to the power supply.

1. Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit. Flip the switch from

240V to 120V conﬁguration. (230 and 115 is printed on switch)

2. Loosen the screw securing the junction box cover and remove the cover.

FIR E P LAC E J UNC TION B OX

120 V

POWER

SUPPLY

(BREAKER

PANEL)

WHITE WIRE - N

RED WIRE –L2

BLACK WIRE – L1

WHITE WIRE - N

BLACK WIRE – L1

GROUND WIRE - G

GREEN WIRE - G

120V INSTALLATION

3. Remove the knockouts (if necessary) or use the provided cable clamp.

4. Pull out the four wires marked L1, L2, N, and G.

5. Connect L1 (black) wire from the unit to the L1 (black) from the power supply.

6. Connect L2 (red) and N (white) from the unit to the Neutral (white) from the power supply.

7. Connect the ground wire (green) from the unit to the ground from the power supply.

8. When the unit has been conﬁgured for the appropriate power supply voltage, ensure that all connections are tight.

9. Insert all the wiring back into the unit and secure with a cable clamp.

!IMPORTANT: The unit is factory conﬁgured for 208/240V operation.

!NOTE:

Use 2 conductor wires with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit.

!NOTE: All wiring must be completed prior to installing the unit.

!NOTE: Ensure that the voltage selector switch is in the proper position for the required supply voltage prior to connecting

the unit to the power supply.

!NOTE: the fan will operate without heat in this application.

1. Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit. Flip the switch from

240V to 120V conﬁguration. (230 and 115 is printed on switch)

2. Loosen the screw securing the junction box cover and remove the cover.

3. Remove the knockouts (if necessary) or use the provided cable clamp.

4. Pull out the four wires marked L1, L2, N, and G.

5. Connect L1 (black) wire from the unit to the L1 (black) from the power supply.

6. Connect L2 (red) and N (white) from the unit to the Neutral (white) from the power supply.

7. Connect the ground wire (green) from the unit to the ground from the power supply.

8. Locate and separate, by installing a wire nut on the 1 (red) and 2 (red).

9. When the unit has been conﬁgured for the appropriate power supply voltage, ensure that all connections are tight.

10. Insert all the wiring back into the unit and secure with a cable clamp.

FIR E P LA CE J UNC TION B OX

120 V

POWER

SUPPLY

(BREAKER

PANEL)

WHITE WIRE - N

RED WIRE –L2

BLACK WIRE – L1

GREEN WIRE - G

WHITE WIRE - N

BLACK WIRE – L1

GROUND WIRE - G

RED - 1

RED - 2

WIRE NUTS

120V INSTALLATION - NO HEAT INSTALLATION

8www.dimplex.com

SECTION D: ALTERNATE CONTROL OPTIONS

240V MAIN POWER WALL SWITCH

!NOTE: This option should not be used with the remote control kit.

!NOTE: Before installing the unit have the following wires installed:

1. A 3 conductor wire with ground (4 wires total) from the power supply panel to the main switch wall box.

2. A 3 conductor wire with ground (4 wires total) from the main switch wall box to the junction box on the unit.

!NOTE: Use a double pole, single throw (On/Off) wall switch that is rated for a minimum of 15 amps.

1. Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit. Ensure that the

switch is in the 240V position. (230 is printed on switch)

2. Loosen the screw securing the junction box cover and remove the cover.

3. Remove the knockouts (if necessary) or use the provided cable clamp.

4. Pull out the four wires marked L1, L2, N, and G. (black, red, white and green)

5. Connect the L1 (black) wire from the unit to the L1 (black) wire from the main power wall switch by using a wire connector

(not supplied).

6. Connect other end of L1 (black) wire from the main power wall switch to the L1 terminal of the main power wall switch.

7. Connect the L2 (red) wire from the unit to the L2 (red) wire from the main power wall switch by using a wire connector

(not supplied).

8. Connect the other end of the L2 (red) wire from the main power wall switch to the L2 terminal of the main power wall

switch.

9. Connect the N (white) wire from the unit to the N

(white) wire from the main power wall switch by

using a wire connector (not supplied).

10. Connect the G (green) wire from the unit to the G

(green) wire from the main power wall switch by

using a wire connector (not supplied).

11. Connect the L1 wire from the power supply to the

L1 terminal of the main power wall switch.

12. Connect the L2 (black) wire from the power

supply to the L2 terminal of the main power wall

switch.

13. Connect the N (white) wire from the power supply

to the remaining N (white) wire from the unit by

using a wire connector.

14. Secure the 2 remaining G (green) wires with a

ground screw in the main switch wall box.

15. Ensure that all connections are tight.

16. Insert all the wiring of the main power wall switch

into the main switch wall box.

17. Insert all the wiring back into the unit and secure

with a cable clamp.

UNITAN D SUPPLY

NEUTRAL FROM

GF ROM UNIT

POWER SUPPLY

GF ROM

L1 FROM

POWER SUPPLY

L2 FROM

L1 FROM UNIT

L2 FROM UNIT

3 CONDUCTOR WIRE

FROM POWER SUPPLY

3 CONDUCTOR WIRE

FROM MAIN SWITCH

UNIT AND SUPPLY

NEUTRAL FROM

L2 FROM UNIT

L1 FROM UNIT

L2 FROM

POWER SUPPLY

L1 FROM

G FROM

POWER SUPPLY

G FROM UNIT

FIR E P LAC E J UNC TION B OX

240 V

POWER

SUPPLY

(BREAKER

PANEL)

WHITE - N

RED –L2

BLACK – L1

WHITE – N

BLACK – L1

GROUND - G

WALL

S WIT CH

RED – L2

GROUND - G

120V MAIN POWER WALL SWITCH

FIR E P LAC E J UNC TION B OX

120 V

POWER

SUPPLY

(BREAKER

PANEL)

WHITE - N

RED –L2

BLACK – L1

WHITE – N

BLACK – L1

GROUND - G

WALL

S WIT CH

GROUND - G

!NOTE: This option should not be used with the remote control kit.

!NOTE: Before installing the unit have the following wires installed:

1. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box.

2. A 2 conductor wire with ground (3 wires total) from the main switch wall box to the junction box on the unit.

!NOTE: Use a single pole, single throw (On/Off) wall switch that is rated for a minimum of 15 amps.

1. Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit. Ensure that the

switch is in the 120V position. (115 is printed on switch)

2. Loosen the screw securing the junction box cover and remove the cover.

3. Remove the knockouts (if necessary) or use the provided cable clamp.

4. Pull out the four wires marked L1, L2, N, and G (black, red, white and green).

5. Connect L1 (black) from the unit to the L1 (black) from the main power wall switch using a wire connector (not supplied).

6. Connect the other end of L1 (black) to the L1 terminal of the main power wall switch.

7. Connect L2 (red) from the unit and N (white) from the unit to the Neutral wire (white) of the main power wall switch by us-

ing a wire connector (not supplied).

8. Connect the other end of the N (white) to the Neutral wire (white) from the power supply panel by using a wire connector

(not supplied).

9. Connect Ground (green) from the unit to the Ground (green) wire of the main power wall switch by using a wire connector

(not supplied).

10. Connect L1 (black) wire from the power supply to the L1 terminal of the main power wall switch.

11. Secure the 2 remaining Ground wires (green) with a ground screw in the main switch wall box.

12. Ensure that all connections are tight.

13. Insert all the wiring of the main power wall switch into the main switch wall box.

14. Insert all the wiring back into the unit and secure with a cable clamp.

FROM MAIN SWITCH

2 CONDUCTOR WIRE

FROM POWER SUPPLY

2 CONDUCTOR WIRE

L1FROM UNIT

GF ROM

POWER SUPPLY

GFRO M UNIT

L1F ROM

POWER SUPPLY

NEUTRALFROM

UNITAN D SUPPLY

UNIT AND SUPPLY

NEUTRAL FROM

POWER SUPPLY

L1 FROM

G FROM UNIT

POWER SUPPLY

G FROM

L1 FROM UNIT

10 www.dimplex.com

!NOTE: This option should not be used with the remote control kit.

!NOTE: Before installing the unit have the following wires installed:

1. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box.

2. A 2 conductor wire with ground (3 wires total) from the main switch wall box to the junction box on the unit.

!NOTE: Use a single pole, single throw (On/Off) wall switch that is rated for a minimum of 15 amps.

1. Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit. Ensure that the

switch is in the 120V position. (115 is printed on switch)

2. Loosen the screw securing the junction box cover and remove the cover.

3. Remove the knockouts (if necessary) or use the provided cable clamp.

4. Pull out the four wires marked L1, L2, N, and G (black, red, white and green).

5. Connect L1 (black) from the unit to the L1 wire (black) from the main power wall switch using a wire connector

(not supplied).

6. Connect the other end of the L1 wire (black) to the L1 terminal of the main power wall switch.

7. Connect L2 (red) from the unit and the N (white) from the unit to the Neutral wire (white) of the main power wall switch by

using a wire connector (not supplied).

8. Connect the other end of the Neutral wire (white) to the Neutral wire (white) from the power supply panel by using a wire

connector (not supplied).

9. Connect the Ground wire (green) from the unit to the Ground wire (green) of the main power wall switch by using a wire

connector (not supplied).

10. Connect L1 (black) from the power supply to the L1 terminal of the main power wall switch.

11. Locate and separate by wire nut the 1 (red) and 2 (red).

12. Secure the 2 remaining Ground wires (green)

with a ground screw in the main switch wall box.

13. Ensure that all connections are tight.

14. Insert all the wiring of the main power wall

switch into the main switch wall box.

15. Insert all the wiring back into the unit and se-

cure with a cable clamp.

FIR E P L AC E J UNC TION B OX

120 V

POWER

SUPPLY

(BREAKER

PANE L)

WHITE - N

RED –L2

BLACK – L1

WHITE – N

BLACK – L1

GROUND - G

WALL

S WIT CH

GROUND - G

RED – 1

RED – 2

WIRE

NUTS

120V MAIN POWER WALL SWITCH - NO HEAT

FROM MAIN SWITCH

2 CONDUCTOR WIRE

FROM POWER SUPPLY

2 CONDUCTOR WIRE

L1 FROM UNIT

G FROM

POWERSUPPLY

G FROM UNIT

L1 FROM

POWERSUPPLY

NEUTRAL FROM

UNIT AND SUPPLY

NEUTRAL FROM

POWER SUPPLY

L1 FROM

G FROM UNIT

POWER SUPPLY

G FROM

L1 FROM UNIT

Other manuals for BF33STP

This manual suits for next models

Table of contents

Languages:

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex Revillusion RBF30 User manual

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE User manual

Dimplex

Dimplex DFI2309 User manual

Dimplex

Dimplex PF3033 User manual

Dimplex

Dimplex OPTIMYST RTOPCS20 User manual

Dimplex

Dimplex BLF50-EU User manual

Dimplex

Dimplex TOLUCA DELUXE-EU User manual

Dimplex

Dimplex EF830 User manual

Dimplex

Dimplex VF2927L User manual

Dimplex

Dimplex Vivente Plus V V T75 Manual

Dimplex

Dimplex 6901860100 Quick start guide

Dimplex

Dimplex MULTIFIRE DF3015 User manual

Dimplex

Dimplex Revillusion RBF30C-AU User manual

Dimplex

Dimplex NAVARRA NAV15P PEBBLE Owner's manual

Dimplex

Dimplex DWF36-PG User manual

Dimplex

Dimplex IN-STUD V1525BT User manual

Dimplex

Dimplex DF3033ST User manual

Dimplex

Dimplex Dimplex VALENCIA User manual

Dimplex

Dimplex DF2690 User manual

Dimplex

Dimplex Revillusion SWD20-AU User manual

Dimplex

Dimplex SP120SP220 User manual

Dimplex

Dimplex BF33ST User manual

Dimplex

Dimplex BF36 Series User manual

Dimplex

Dimplex EF2570G-IR User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual