Dimplex ENG56-400 Technical manual

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)

EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC

08/51804/0 Issue 4

Pro Range

ENG56-400, ENG68-400, ENG56-600

Fig. 4 Fig. 4a

Fig. 2 Fig. 3

Fig. 1

255

168 Y

MODEL ‘H’ ‘W’ ‘X’ ‘Y’

ENG56-400 700mm 490mm 413mm 395mm

ENG68-400 823mm 490mm 413mm 517mm

ENG56-600 700mm 646mm 569mm 395mm

Fig. 5 Fig. 5a

Fig. 5b Fig. 6

Fig. 7 Fig. 8

Fig. 10

Fig. 11 Fig. 12

Fig. 13 Fig. 14

Fig. 9

Fig. 15

Fig. 16

Fig. 17

UK .................................................................................................................................... 1

DE..................................................................................................................................... 7

FR .................................................................................................................................. 13

ES................................................................................................................................... 19

PT .................................................................................................................................. 25

IT.................................................................................................................................... 30

NL.................................................................................................................................. 36

DK ................................................................................................................................. 42

ENG56-400, ENG68-400, ENG56-600

Introduction

Please read this information guide carefully to be able to safely install, use and maintain your product.

Important Safety Advice

When using electrical appliances, basic precautions should always be followed to reduce the risk of ﬁre, electrical

shock and injury to persons, including the following:

1. OVERHEATING

WARNING: In order to avoid overheating, do not cover the heater. Do not place material or garments on the heater, or

obstruct the air circulation around the heater. The heater carries a DO NOT COVER warning.

2. DAMAGE.

If the appliance is damaged, check with the supplier before installation and operation.

If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualiﬁed person

in order to avoid a hazard.

3. LOCATION

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower or swimming pool.

Do not locate the heater immediately below a ﬁxed socket outlet or connection box.

Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre from the heater.

Although this heater conforms with safety standards, we do not recommend its use on deep pile carpets or on long

hair type of rugs.

4. PLUG POSITIONING

The appliance must be positioned so that the plug is accessible.

Keep the supply cord away from the front of the heater.

5. USE OF OTHER CONTROLS

Do not use this heater in series with a thermal control, a program controller, a timer or any other device that switches

on the heat automatically, since a ﬁre risk exists when the heater is accidentally covered or displaced.

6. UNPLUGGING

In the event of a fault unplug the device.

Unplug the device when not required for long periods.

7. OWNER/USER

This appliance is not intended for use by children or persons with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with

the appliance.

8. ELECTRCITY

WARNING – THIS APPLIANCE MUST BE EARTHED.

This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the

supply voltage.

Before switching on, please read the safety advice and operating instructions.

General Information

Only use ﬁltered water in this appliance.

Always ensure that the appliance is sitting on a level surface.

Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long

hair type of rugs.

Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is

related to the operation of the ﬂame effect. This is normal and should not be a cause for concern.

If this product experiences a power surge for whatever reason the product may cut-out. This is a normal safety feature

and the product will resume operation after 30 seconds.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.

If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the

sump.

The water tank, sump, sump lid, tank cap and air ﬁlters must be cleaned once every two weeks, particularly in hard

water areas.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under ‘Maintenance’ and ‘Changing lamps’.

The sump and the water tank in this product are treated with a biocidal product, Silver Biocide. This conforms with the

latest relevant ISO standard 1

Installation Instructions

This section describes how to set up your ﬁre.

BEFORE YOU START

1. Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible

future use e.g. in the event of moving house or returning the appliance to your supplier.

2. Before connecting the appliance, check that the supply voltage is the same as that stated on the heater.

Connecting the Transducer Unit + Lamps

1. Release the two red tabs by turning them by 90 degrees (Fig 2)

2. Lift out the Sump Nozzle (Fig 3)

3. Insert lamps into lamp holders (Fig 4), carefully locating the pins into the holes (Fig 4a)

4. Push lamps ﬁrmly into place

5. Place the Transducer Unit into the sump and join the cable to the connector on the sump (Fig 5)

6. To ensure that the Transducer Unit is correctly placed in the sump, the tab on the Transducer Unit should be lined

up with the moulded recess in the sump (Fig 5a).

7. Ensure that the cable is not placed above the disc on the Transducer Unit (Fig 5b). To prevent the cable becoming

pinched between the nozzle and the sump, place the cable in the slot in the wall of the sump.

8. Replace the Sump Nozzle and secure it by turning the two red tabs by 90 degrees (Fig 6)

Filling the Water Tank

9. Place Water Tank in sink and remove cap (turn anti-clockwise to open) (Fig 7)

10. Fill Water Tank with ﬁltered tap water only. This is necessary to prolong the life of the ﬂame and smoke

producing unit. The water should be ﬁltered through a conventional domestic water ﬁlter unit and the ﬁlter should

be replaced regularly. Distilled water must not be used.

11. Screw the cap back on – do not overtighten.

12. Place the Water Tank in the Sump, with the tank cap facing down and the ﬂat side of the tank facing outward (Fig 8)

Assembling the ﬁre

13. Place the Fuelbed on top of the Water Tank and Mist Nozzle (Fig 9)

Operating the Fire

This section describes how to activate your ﬁre using either the manual controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the hinged ﬂap. (Fig.10 for Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the Fire.

Note: This switch must be in the ‘ON’ ( I ) position for the Fire to operate either with or without heat.

Switch ‘B’:- Press once to turn on the ﬂame effect. This will be indicated by an audible beep. Although the main

lights operate immediately it will take a further 30 seconds before the ﬂame effect starts.

Press again to give ﬂame effect and half heat. This will be indicated by two beeps.

Press again to give ﬂame effect and full heat. This will be indicated by three beeps.

Press

again to return to ﬂame effect only. This will be indicated by one beep.

Press to put ﬁre in to standby mode. This will be indicated by one beep.

Control Knob ‘C’:- Controls the Thermostat setting.

Turning the control knob to the left will decrease the temperature setting, turning the control knob

to the right will increase the temperature setting.

Control Knob ‘D’:- Controls the intensity of the ﬂame effect.

Turning the control knob to the left increases the ﬂame effect, turning the control knob to the right will

decrease the ﬂame effect.

SETTING THE THERMOSTAT

Ensure the ﬁre is plugged in and switch it on to the full heat setting. Turn the Control Knob ‘C’ fully to the right (max

temperature setting) to warm the room rapidly. When the room temperature has reached the desired level, turn

the thermostat knob back slowly until you hear the thermostat just click off. The heater will then maintain the room

temperature at the chosen level.

GENERAL TIPS

Only use ﬁltered tap water in this appliance.

Always ensure that the appliance is sitting on a level surface.

If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under ‘Changing lamps’.

FILLING THE WATER TANK

When the water tank is empty, the ﬂame and smoke effect shuts off and you will hear 2 audible beeps, follow these

steps.

1. Press Switch ‘A’ to (0) (Fig.10)

2. Gently lift out the fuelbed and carefully set aside.

3. Remove the water tank by lifting upwards and outwards.

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (Fig 7)

5. Fill tank with ﬁltered tap water only. This is necessary to prolong the life of the ﬂame and smoke producing unit.

The water should be ﬁltered through a conventional domestic water ﬁlter unit and the ﬁlter should be replaced

regularly.

6. Screw the cap back on, do not over tighten.

7. Return the tank to the sump, with the tank cap facing down and the ﬂat side of the tank facing outward. (Fig 8)

8. Gently place the fuelbed back into position. (Fig 9)

9. Press Switch ‘A’ to ‘ON’ (I) position (Fig.10)

CHANGING LAMPS

If the ﬂame and smoke effect appears grey or colourless it may be that one or more lamps have failed.

You can check for lamp failure as follows.

Note: Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room

temperature being higher then the thermostat setting

THERMAL SAFETY CUT-OUT

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if

the heat outlet was restricted in any way. If the cut-out operates, unplug the heater from the socket outlet and allow

approximately 10 minutes before reconnecting. Before switching the heater back on remove any obstruction that may

be restricting the heat outlet, then continue normal operation.

Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be

supplied through an external switching device, such as a timer, or connected to a switch that is regularly switched on

and off by the utility.

GETTING THE DESIRED FLAME EFFECT

1. The ﬂame control knob ‘D’ (Fig.10) may be turned up or down to give a more realistic effect.

2. Generally the ﬂames appear more realistic when the ﬂame control is turned down.

3. Give the ﬂame generator time to react to changes you may make.

4. The ﬁre will use less water if the ﬂame effect is set to a lower level.

5. Do not tilt or move the ﬁre while there is water in the tank or sump.

6. Make sure that the ﬁre is on a level ﬂoor.

REMOTE CONTROL OPERATION

On the control panel, Switch A (Fig.10) must be in the ‘ON’ ( I ) position in order for the remote control to operate.

There are 3 buttons on the remote control. (Fig.12) To operate correctly the remote must be pointed towards the front

of the grate. (Fig 17). The remote control functions are as follows:

Press once to turn on Flame effect only.

This will be indicated by one beep.

Press once to turn on Half Heat and Flame Effect.

This will be indicated by two beeps.

Press again to turn on Full Heat and Flame Effect.

This will be indicated by three beeps.

Standby

This will be indicated by one beep.

Maintenance

1. Leaving the ﬂame effect on, lift out the fuelbed and water tank.

2. It should be possible to view the lamps with the nozzle in place and observe which one needs to be changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the ﬁre from the mains.

4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.

5. Remove the sump as described in the Cleaning Section.

6. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder, (Fig.4 and

4a).

Replace with an OPTIMYST, 12V, 45W, Gu5.3 base, 8º beam angle, coloured lamp. (Purchased from our your

supplier)

7. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push ﬁrmly in place. (Fig.4 and

4a).

8. Replace the sump, nozzle, water tank and fuelbed.

CLEANING

Warning – Always press Switch ‘A’ to the ‘OFF’ (0) position (Fig.10) and disconnect from the power supply before

cleaning the ﬁre.

We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-

Water Tank, Sump, Nozzle, Tank cap and seal, Air ﬁlter.

For general cleaning use a soft clean duster – never use abrasive cleaners.

To remove any accumulation of dust or ﬂuff the soft brush attachment of a vacuum cleaner should occasionally be

used to clean the outlet grille of the fan heater.

Water tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in

the outer groove and the centre rubber seal.

3. Put a small quantity of washing up liquid into the tank, reﬁt the cap and shake well, rinse out until all traces of

washing up liquid are gone.

4. Reﬁll with ﬁltered tap water only, replace the cap, do not overtighten.

Sump

1. Press Switch ‘A’ to the ‘OFF’ (0) position

2. Gently lift out the fuelbed and place carefully on the ground.

3. Remove the water tank by lifting upwards.

4. Disconnect the electrical connector, located on the right side of the sump. (Fig.5) .

5. Release the right sump locking tabs by turning 90º. This allows the sump to be lifted completely from its location.

(Fig. 11)

6. Gently lift up the sump, taking care to keep level so as not to spill any water. Sit the assembly in the sink.

7. Release the left sump locking tabs by turning 90º, then lift off the Nozzle. (Fig.3)

8. Lift out the transducer and carefully tilt, as shown, so that the liquid drains out of the sump. (Fig.13)

9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces in the

sump and gently clean the transducer including the metal discs located in the top grooved surface. (Fig.14)

10. When cleaned, thoroughly rinse the sump with clean water to remove all traces of washing up liquid.

11. Clean the Nozzle with the brush and ﬂush out thoroughly with water. (Fig.15)

12. Reverse the above steps to reassemble.

Air ﬁlter

1. Gently lift out the fuelbed and place carefully on the ground.

2. Gently slide the air ﬁlter upwards out of its plastic holder. (Fig.16)

3. Gently rinse with water in the sink and dry with fabric towel before returning.

4. Replace the ﬁlter making sure that the coarse black ﬁlter is facing the front of the ﬁre.

5. Replace the fuelbed.

Other manuals for ENG56-400

This manual suits for next models

Table of contents

Languages:

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex BINGHAM BHM 10 User manual

Dimplex

Dimplex DFP15-1134NG User manual

Dimplex

Dimplex Toluca Deluxe User manual

Dimplex

Dimplex XLF60 User manual

Dimplex

Dimplex BAR20-AU User manual

Dimplex

Dimplex Revillusion RBF30 User manual

Dimplex

Dimplex IGNITE XL BOLD User manual

Dimplex

Dimplex Optiflame 3D Braemar BMR20 Instruction Manual

Dimplex

Dimplex ELGAR EGR20 User manual

Dimplex

Dimplex CAS400LNH-INT User manual

Dimplex

Dimplex DFR2551G User manual

Dimplex

Dimplex LAGsu User manual

Dimplex

Dimplex EWM-COPPER Quick start guide

Dimplex

Dimplex SP620 User manual

Dimplex

Dimplex ASP20 User manual

Dimplex

Dimplex MULTIFIRE DF3015 User manual

Dimplex

Dimplex DFB4047 User manual

Dimplex

Dimplex Shaftsbury SHA20 User manual

Dimplex

Dimplex DF3033ST User manual

Dimplex

Dimplex CDFI400RH User manual

Dimplex

Dimplex DF28L-PRO User manual

Dimplex

Dimplex EWM-COPPER User manual

Dimplex

Dimplex LVA191 User manual

Dimplex

Dimplex BF9000 User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual