Dimplex HAW1000N User manual

470

207

115

Dimensions

(millimetres)

Air Warmer: Model No. HAW1000N

Installation and Operating Instructions

Fig. 1

08/50511/0 Issue 0

Watts Electrical Supply Weight (kg)

HAW1000N 1000 230-240V ~1PN 14

Important Safety Advice

Do not locate above or below a fixed socket outlet.

The heater including the supporting legs can get very hot;

therefore do not mount directly on any combustible

material. Suitable fire resistant material is required

between the heater and any combustible base or support.

Warning: Before obtaining access to the terminals all supply

circuits must be disconnected.

The heater should be installed to allow a reasonable air

flow around the heater.

A prominent notice should be provided where the heater

is sited ‘Keep Clear and Unobstructed’.

Avoid exposure to water.

The heaters are not suitable for general domestic use.

The heater is suitable for a drying room provided that the

heater has suitable ventilation.

A mains lead which can operate at + 110°C must be used.

An all-pole isolating switch with a minimum separation of

3mm in each pole must be fitted adjacent to the heater to

facilitate local isolation.

General

This carton contains:

•1 HAW1000N heater

•1 Foldable guard

Electrical connection

WARNING – THISAPPLIANCE MUST BE EARTHED.

Verify that the electrical supply cable is sufficient for the rated loading.

Check that the incoming supply conforms to the rated supply.

The heater power circuit must be protected by a suitably rated over

current device.

The incoming cables must be connected to the factory fitted heater

terminals provided. Do not alter any factory fitted wiring.

The Terminal Cover Casting can be removed to access the terminals, by

removing the 2 screws fixing the cover - see Fig. 2.

WARNING: Ensure the power cable path does not come into contact

with the heater element.

The heater is supplied with an earth stud, located inside the terminal box,

which must be connected to earth.

After connection check the continuity of earth connections.

Installation

The installation should be carried out by a suitably qualified electrician/

engineer in accordance with applicable standards.

Remove all items from the packaging. The heater should be fixed using

the fixing points provided - see Fig. 3. Ensure the heater is securely

fastened.

Remove the terminal cover and connect the mains cable, while making

note of the path the connecting cable should take through the guard.

Reattach the terminal cover to the heater and fasten the cable gland.

Mount the guard over the heater. Ensure the guard is mounted centrally

relative to the heater as shown in Fig. 4.

The heater should not be connected until the instruction leaflet has been

read fully.

Fig.2

449

179

Fig.3

THESEINSTRUCTIONS SHOULD BEREAD CAREFULLYANDRETAINEDFOR FUTURE REFERENCE

674

364

188

229

663

The product complies with the European Safety Standards BS EN60079 and the European Standard Electromagnetic Compatibility (EMC)

EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

Thermal Safety Cut-out

The thermal cut-out will operate and the power supply to the heating

element will be interrupted if ventilation of the heater is impaired.

Before resetting the thermal cut-out, the cause of the impaired ventilation

should be established and eliminated.

Procedure for resetting cut-out

1. Disconnect power supply.

2. Remove the guard.

3. Remove the terminal cover to access the thermal cut-out - see Fig. 2.

4. Press the reset tab located in the centre of the cut-out (cut-out clicks

when reset) - see ‘x’ in Fig. 2.

5. Re-fit the terminal cover and reconnect power supply.

6. Re-fit the guard.

If the cut-out continues to operate intermittently, the heater should be

switched off and a service agent contacted.

Fig.4

Cleaning and User Maintenance

WARNING: DISCONNECTSUPPLYbeforecarrying out maintenance.

The heater should be subject to a regular maintenance schedule with the

following actions as a minimum:

·Checkthattheheatersurfacesarecleanandfreefromanydeposits.

The heater can be cleaned by wiping with a damp cloth. Neither

abrasive cleaning powders nor furniture polish should be used.

·The internal wiring shall be clean and dry, with no apparent

deterioration of the wiring insulation.

·All connections shall be tight, without signs of overheating.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it should not

be disposed of with household waste.

Please recycle where facilities exist. Check with your Local

Authority or retailer for recycling advice in your country.

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free

of charge (excluding element & subject to availability) provided it has

been installed and operated in accordance with these instructions. Your

rights under this guarantee are additional to your statutory rights, which

in turn are not affected by this guarantee.

Should you require after sales service you should contact our customer

services help desk on 0845 600 5111 It would assist us if you can quote

the model number, series, date of purchase, and nature of the fault at the

time of your call. The customer services help desk will also be able to

advise you

should you need to purchase any spares.

Please do not return a faulty product to us in the first instance as this

mayresultinlossordamageanddelayinprovidingyouwith a satisfactory

service. Please retain your receipt as proof of purchase.

Dimplex UK Ltd.

Millbrook House

Grange Drive

Hedge End

Southampton

Hampshire. SO30 2DF

[c] Dimplex UK Limited

UK customer help line 8.00am–5.00pm Mon-Fri and 8:30am-1.00pm Sat (October-March)

Technical Services: Tel. 0845 600 5111

Fax. 01489 773053

e-mail [email protected]

Republic of Ireland Tel. 01 8424833

Table of contents

Other Dimplex Heater manuals

Dimplex

Dimplex ARLWP800TI User manual

Dimplex

Dimplex EUH02B21T User manual

Dimplex

Dimplex CMH Series User manual

Dimplex

Dimplex GFP200 W User manual

Dimplex

Dimplex LC Series User manual

Dimplex

Dimplex EF 12/20 TI User manual

Dimplex

Dimplex RCH5031W User manual

Dimplex

Dimplex RCH5031CXW User manual

Dimplex

Dimplex Monterey MFP050 User manual

Dimplex

Dimplex Quantum series User manual

Dimplex

Dimplex XLS User manual

Dimplex

Dimplex DXLWP800TI B User manual

Dimplex

Dimplex OFC12 User manual

Dimplex

Dimplex Studio G DXSTG25 User manual

Dimplex

Dimplex DTX Series Installation instructions manual

Dimplex

Dimplex ECR15 User manual

Dimplex

Dimplex R23DH Series User manual

Dimplex

Dimplex DuoHeat Duo300N User manual

Dimplex

Dimplex OFC1000 User manual

Dimplex

Dimplex Apollo APL100 Owner's manual

Dimplex

Dimplex CXD2000H-NA Series User manual

Dimplex

Dimplex Quantum User manual

Dimplex

Dimplex QM070 Quantum User manual

Dimplex

Dimplex LCM Series User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide