Digitus DA-70202 User manual

User Manual

USB2.0 to IDE and SATA Adapter Cable

Model: DA-70202

I. Foreword

Congratulations on your purchase of our product! We will

show you a new storage concept with safety and convenience.

It is our pleasure to give you the best solution to expand your

HDD'S Capacity and enhance your data's reliability in PC

system or Mac system. Before using the product, please read

this manual carefully for further recognizing of the product.

II. System Requirement

Basic environment for setup this device:

Hardware requirement: a PC, Notebook or Mac system

with free USB interface

Operation system: Windows7/8/10/Vista/XP/2000,

Mac OS 9.x above

III. Feature

1. Supports IDE/SATA 2.5/3.5/5.25 devices

2. Support USB2.0 to Serial ATA interface, transfer rate

up to 480Mb/sec

2. Support USB2.0 to IDE interface, transfer rate up to

480Mb/sec

3. Bus power for 2.5 Hard Disk

IV. Package Content

• USB to IDE/SATA Adapter cable

• Supported CD Driver

• User's Manual

4pin Power

USB2.0 Power Plug(red)

Power/Activity-LED

(blue & red)

USB2.0 Plug

Plug fo

SATA device

44-pin IDE plug fo

1.8/2.5 IDE HDD

40-pin IDE plug fo

3.5/5.25 IDE device

Note: For 3.5/5.25 IDE devices, please plug in a 5V/12V power

supply (not included) to appropriate port on the back side of

HDD or DVD, so that the PC power switch (on/off) can’t control

the current to HDD or DVD. If you want to cut off the current to

HDD or DVD, then you need to plug out the power plug from

3.5” IDE HDD or 5.25 DVD devices.

Both IDE and SATA plug are protected against polarity

reversal and should be easily connected to the device. If not,

Pease check if you use the plug in the right way. Please be

sure, that your IDE device is configured as MASTER.

SATA Plug LED

LED

V. Hardware installation

a. Connect to a 2.5 SATA HDD

b. Connect to a 2.5 IDE HDD

For a 2.5 SATA HDD or IDE HDD, plug directly the SATA

connector or the 44pin connector into the appropriate ports

on the rear of the HDD, and plug the USB signal/data plug

(Black) into USB port of PC.

Note: If you HDD need more than 500mA, please plug

the USB extra power plug (Red) additionally into other

USB port.

44pin IDE Plug

3.5 SA

HDD

5V/12V Power suppl

(Please see chapter VIII. How to use power supply from

your desktop computer). Alternatively, you can use

5V/12V external power supply

3.5 IDE HDD 5V/12V Power supply

LED

c. Connect to a 3.5 SATA HDD

d. Connect to a 3.5 IDE HDD

For a 3.5 SATA HDD or a 3.5 IDE HDD, plug directly the

SATA connector or the 40pin connector into the appropriate

ports on the rear of the HDD, and plug the USB

signal/data plug(Black) into USB port of PC, then plug the

4-pin plug of the power supply (not included) to the 4-pin

power jack (for IDE HDD direct plug in HDD power

connector), and the other end plug to power source.

e. Connect to a 5.25 IDE HDD

For a 5.25 CD/DVD device, plug directly the 40pin

connector into the appropriate ports on the rear of the

CD/DVD device, and plug the USB signal/data plug (Black)

into USB port of PC, then plug the 4-pin plug of the power

supply to the 4-pin power jack (for IDE CD/DVD direct plug

in CD/DVD power connector), and the other end plug to

power source.

VI. Driver installation

a. Setup mode under Windows7/8/10/Vista/XP/2000

system

Under Windows7/8/10/Vista/XP/2000, the system will find

and setup [USB Mass Storage Device] directly

b. Setup mode under Mac OS system

If your system is Mac OS9.0 or above, the system can find

the driver directly. If your system is OS8.6, you have to

download and setup [USB MASS STORAGE SUPPORT

1.3.5] from SOFTWARE SUPPORT

Website : http://www.apple.com/support

5V/12V

Power supply

VII. Under the following situation, you need to use

5V/12V Power supply

1)When connects with the 3.5 / 5.25 SATA devices

( HDD, CD ROM , DVD Rom )

2)When this product connect with 3.5 / 5.25 IDE devices

( HDD , CD Rom , DVD Rom )

3) Connecting with the 2.5 SATA HD, when the power

consumption is bigger than 1A

4) Connecting with the 1.8 / 2.5 IDE HDD, when

power consumption is bigger than 1A

* Remove the multi-function adapter

Warning: Before removing the multi-function, you must

finish the following procedure:

1) Click the icon in the [Desktop] window of your computer

2) A [Safely Remove Hardware] message window will

appear, click the [Stop] button

3) [It is now safe to remove the USB device] message will

appear, close the [Safely Remove Hardware] window

4) Turn the power switch to [OFF] position

5) Remove the 5V/12V power supply if it is applied

Note:

New Hard Disk Drive must be formatted before

in use

VIII. How to use the device with power supply

from computer

1. Plug DA-70202 into USB port

2. Plug 3,5HDD into the correspondent port ( SATA/IDE)

3. Plug the power for supplying mentioned devices in Point

VII. from computer

Also, for 5,25 devices

Connect from the 4 pin power connector of the

power supply to DA-70202 (4Pin DC)

Power supply

Disclaimer

Hereby ASSMANN Electronic GmbH, declares that this device is in

compliance with the requirements of Directive 2014/30/EU and the

Directive 2011/65/EU for RoHS compliance. The complete

declaration of conformity can be requested by post under the below

mentioned manufacturer address.

Warning:

This device is a class B product. This equipment may cause some

radio interference in living environment. In this case, the user can be

requested to undertake appropriate measures to prevent

interference.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3

58513 Lüdenscheid

Germany

All the information in this document is

subject to change without prior notice. The

manufacturer makes no representations or

any warranties regarding the Contents of this

manual. The information contained in this manual

is provided for the general use by the customers.

No part of this document may be reproduced or

transmitted in any form by any means without the

express written permission of The

manufacturer. All brand names and product

names used in this document are trademarks or

registered

trademarks of their respective holders.

Table of contents

Other Digitus Adapter manuals

Digitus

Digitus DA-71101 User manual

Digitus

Digitus DA-70841 User manual

Digitus

Digitus DA-70842 User manual

Digitus

Digitus DN-10180 User manual

Digitus

Digitus DN-70440-1 User manual

Digitus

Digitus DA-70857 User manual

Digitus

Digitus DA-70156 User manual

Digitus

Digitus eSATA CARDBUS ADAPTER User manual

Digitus

Digitus DN-70550 User manual

Digitus

Digitus DA-70148-3 User manual

Digitus

Digitus DA-70851 User manual

Digitus

Digitus DA-70200-1 User manual

Digitus

Digitus DA-70250-1 User manual

Digitus

Digitus DN-70566 User manual

Digitus

Digitus DN-7003GS User manual

Digitus

Digitus WNP-UA300-01 User manual

Digitus

Digitus DN-70560 User manual

Digitus

Digitus DA-70850 User manual

Digitus

Digitus DA-70453 User manual

Digitus

Digitus DN-7053-1 User manual

Digitus

Digitus DA-70167 User manual

Digitus

Digitus DA-70838 User manual

Digitus

Digitus DA-70853 User manual

Digitus

Digitus UNIVERSAL TRAVEL ADAPTER User manual

Popular Adapter manuals by other brands

PCB Piezotronics

PCB Piezotronics 090B274 Installation and operating manual

Auvidea

Auvidea J20 Technical reference manual

Gossen MetraWatt

Gossen MetraWatt AT3-III E operating instructions

Akribis

Akribis ITF-21-BISS-MIT user manual

Tenda

Tenda W54U user guide

ROHO

ROHO AGILITY Operation manual

PROLiNK

PROLiNK WN2001 Quick installation guide

Hawking

Hawking HUF2 Specifications

Airlink101

Airlink101 AWLC4030 user manual

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter user manual

Philips

Philips SWA4554S/10 user manual

JVC

JVC TS-C9D2B Assembly and installation instructions

NETGEAR

NETGEAR A6100 quick start

D-Link

D-Link DWA-121 Quick install guide

Philips

Philips SWA2037 Specifications

Basalte

Basalte 0610-20 installation manual

Yealink

Yealink EHS40 user guide

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A installation guide