Desa The Aspen GL36STEP Quick start guide

Save this manual for future reference.

For more information, visit www.desatech.com

THE ASPEN

NATURAL GAS MODELS GL36ST AND GL36STE

PROPANE/LP GAS MODELS GL36STP AND GL36STEP

2-SIDED (SEE-THROUGH), VENTED DECORATIVE GAS APPLIANCE

OWNER’S OPERATION AND INSTALLATION MANUAL

FOR YOUR SAFETY

— Do not store or use gasoline or any other ﬂammable

vapors or liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS :

• Do not try to light any appliance.

• Do not touch any electrical switch;

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

WARNING: If the information in these instructions is

not followed exactly, a ﬁre or explosion may result

causing property damage, personal injury or death.

www.desatech.com 55173-F2

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualiﬁed installer, service

agency or the gas supplier.

NOT FOR USE WITH SOLID FUEL

CHECK LOCAL CODES PRIOR TO INSTALLATION

SAVE THIS BOOK

This book is valuable. In addition to instructing you on

how to install and maintain your appliance, it also con-

tains information that will enable you to obtain replace-

ment parts or optional accessory items when needed.

Keep it with your other important papers.

This appliance is only for use with the type of gas indi-

cated on the rating plate.

This appliance is not convertible for use with other

gases.

TABLE OF CONTENTS

Safety Information ............................................... 3

Dimensions .......................................................... 4

Introduction .......................................................... 5

Selecting Location ............................................... 5

Fireplace Installation ........................................... 6

Operating Fireplace ........................................... 13

Cleaning and Maintenance ................................ 15

Technical Service .............................................. 15

Speciﬁcations .................................................... 15

Wiring Diagrams ................................................ 16

Troubleshooting ................................................. 17

Replacement Parts and Accessories ................. 19

Limited 2-Year Warranty ....................... Back Page

www.desatech.com

55173-F 3

SAFETY INFORMATION

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this ﬁreplace.

Improper use of this ﬁreplace

can cause serious injury or death

from burns, ﬁre, explosions,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

This ﬁreplace is a vented product. This ﬁreplace

will not produce any gas leakage into your home if

properly installed. This ﬁreplace must be properly

installed by a qualiﬁed service person. If this unit is

not properly installed by a qualiﬁed service person,

gas leakage can occur.

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the ﬂu, with

headaches, dizziness or nausea. If you have these

signs, the ﬁreplace may not have been installed

properly. Get fresh air at once! Have ﬁreplace

inspected and serviced by a qualified service

person. Some people are more affected by carbon

monoxide than others. These include pregnant

women, people with heart or lung disease or

anemia, those under the inﬂuence of alcohol and

those at high altitudes.

Propane/LP gas and natural gas are both odorless.

An odor-making agent is added to each of these

gases. The odor helps you detect a gas leak. How-

ever, the odor added to these gases can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all warnings.

Keep this manual for reference. It is your guide to

safe and proper operation of this ﬁreplace.

WARNING: Any change to

this ﬁreplace or its controls can

be dangerous.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This ap-

pliance is not convertible for use with other

gases.

2. For propane/LP ﬁreplace, do not place propane/

LP supply tank(s) inside any structure. Locate

propane/LP supply tank(s) outdoors. To prevent

performance problems, do not use propane/LP

fuel tank of less than 100 lbs. capacity.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplier's

instructions

• if you cannot reach you gas supplier, call the

ﬁre department.

4. Never install the ﬁreplace

• in a recreational vehicle

• where curtains, furniture, clothing or other

ﬂammable objects are less than 42" from

the front, top or sides of the ﬁreplace

• in high trafﬁc areas

• in windy or drafty areas

5. This ﬁreplace reaches high temperatures. Keep

children and adults away from hot surfaces to

avoid burns or clothing ignition. Fireplace will

remain hot for a time after shutdown. Allow

surfaces to cool before touching.

6. Carefully supervise young children when they

are in the room with ﬁreplace.

7. A hearth extension is not required with this

appliance. If one is installed, it is for aesthetic

purposes only and does not have to meet the

standard requirements.

8. Turn ﬁreplace off and let cool before servicing

or repairing. Only a qualiﬁed service person

should install, service or repair this ﬁreplace.

Have ﬁreplace inspected annually by a quali-

ﬁed service person.

9. You must keep control compartments, burn-

ers and circulating air passages clean. More

frequent cleaning may be needed due to ex-

cessive lint and dust from carpeting, bedding

material, etc. Turn off the gas valve and pilot

light before cleaning ﬁreplace.

10. Have venting system inspected annually by a

qualiﬁed service person. If needed, have vent-

ing system cleaned or repaired. See Cleaning

and Maintenance, page 15.

www.desatech.com 55173-F4

11. Keep the area around your ﬁreplace clear of

combustible materials, gasoline and other

ﬂammable vapor and liquids. Do not run ﬁre-

place where these are used or stored. Do not

place items such as clothing or decorations on

or around ﬁreplace.

12. Do not use this ﬁreplace to cook food or burn

paper or other objects.

13. Do not use any solid fuels (wood, coal, paper,

cardboard, etc.) in this ﬁreplace. Use only the

gas type indicated on ﬁreplace nameplate.

14. This appliance, when installed, must be electri-

cally grounded in accordance with local codes

or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70 or

the Canadian Electrical Code, CSA C22.1.

15. Do not obstruct the ﬂow of combustion and

ventilation air in any way. Provide adequate

clearances around air openings into the combus-

tion chamber along with adequate accessibility

clearance for servicing and proper operation.

SAFETY INFORMATION

Continued

16. Do not install ﬁreplace directly on carpeting,

vinyl tile or any combustible material other

than wood. The ﬁreplace must set on a metal

or wood panel extending the full width and

depth of the ﬁreplace.

17. Do not use ﬁreplace if any part has been ex-

posed to or under water. Immediately call a

qualiﬁed service person to arrange for replace-

ment of the unit.

18. Do not operate ﬁreplace if any log is broken.

19. Do not use a blower insert, heat exchanger

insert or other accessory not approved for use

with this ﬁreplace.

20. Provide adequate clearances around air

openings.

6" O.D.

36 1/2"

42 1/2"

20 1/2"

52 1/2"

24"

21 1/4"

42 1/2"

9 1/2"

19"

4 1/2"

12"

16"

13"

5 1/2"

2 1/2"

6"(152 mm)

15 1/4"

37 1/2"

1 1/2"

8"(203 mm)

7 1/2"

(2 1/2")

(483 mm)

(114 mm)

(64mm)

(406 mm)

(305 mm)

(330 mm)

(229 mm) (140 mm)

(953 mm)

(38 mm)

(610 mm)

(927 mm)

(1080 mm)

(1334 mm)

(521 mm)

(191 mm)

(64 mm)

(540 mm) (387 mm)

(1080 mm)

(241 mm)

(152 mm)

SIDE VIEW FRONT VIEW

TOP VIEW

DIMENSIONS

www.desatech.com

55173-F 5

Figure 2 - Typical Two-Sided Fireplace

Installation

INTRODUCTION

Models GL36ST/P and GL36STE/EP are decora-

tive gas appliances that use a millivolt gas control

and piezo pilot or an electronic gas control valve

with an electronic ignition system respectively.

These systems require a 6", B-type venting system

for operation.

The 6" B-type vent is not supplied by DESA.

For installation guidelines, check your B-vent

instructions.

WARNING: This gas appli-

ance must not be connected to

a chimney ﬂue servicing a solid

fuel burning appliance.

Models GL36ST and GL36STE are smooth face

units for natural gas only. The GL36STP and

GL36STEP are smooth face units for propane/LP

gas only. To determine which type of gas your unit

is approved and tested for, check the rating plate on

the lift-out plate located inside the ﬁrebox under

the access panel.

BEFORE YOU BEGIN

Before beginning the installation of your appli-

ance, read these instructions through completely.

This DESA appliance and its approved compo-

nents are safe when installed according to this

installation manual and are operated as recom-

mended by DESA. Unless you use DESA approved

components tested for this appliance, YOU MAY

CAUSE A FIRE HAZARD!

The DESA warranty will be voided by and DESA dis-

claims any responsibility for the following actions :

A) Modiﬁcation of the appliance or any of the

components manufactured by DESA unless

otherwise permitted by DESA.

B) Use of any component part not approved by

DESA in combination with this appliance.

C) Installation and/or operation in a manner other

than instructed in this manual.

D) The burning of anything other than the type of

gas approved for use in this gas appliance.

This appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electri-

cal Code, ANSI/NFPA 70-1987 and the CSA C22.1

Canadian Electrical Code for Canada.

The installation must conform with local codes

or, in the absence of local codes, with the current

National Fuel Gas Code, ANSI Z223.1/NFPA 54

or with the current CAN/CGA B149 Installation

Codes for Canada.

This appliance complies with ANSI Z21.50B-1990

and CAM/CGA-2.22-M89 as a Vented Gas Ap-

pliance and is listed and tested by the Omni Test

Laboratories.

WARNING: Installation of

this appliance should be done

by a qualiﬁed service person

well trained in the installation

of such appliances. You will

also need a building permit from

your local Building and Safety

Commissioner before installing

this appliance; otherwise your

insurance company may not

cover this appliance.

NOTICE: This appliance is not

intended to be used as a primary

source of heat.

SELECTING LOCATION

To determine the safest and most efﬁcient location

for your appliance, you must take into consider-

ation the following guidelines:

1. The location must allow for proper clearances

(see Clearances, page 6). Note: This decora-

tive appliance is not designed for outdoor

installation.

2. The location should be in a place where drafts,

air conditioning ducts, windows or doors will

not affect ﬁreplace heat output.

3. A location that avoids the cutting of joists

or roof rafters will make installation easier.

Figure 2 shows a typical two-sided ﬁreplace

installation.

IMPORTANT: All ﬁreplace openings must be

located at least 3 feet from facing wall or com-

bustible material.

Existing

Side

Wall

4" From Opening to

Perpendicular Wall

Projected

Wall

www.desatech.com 55173-F6

Figure 3 - Clearances from Top View

Figure 4 - Clearances from Side View

MANTEL CLEARANCES

Woodwork, such as wood trims, mantels and other

combustible materials, should not be placed within

7" of the opening of this appliance (see Figure

5). Combustible material above the fireplace

projecting more than 1 1/2" from the applianceʼs

front face must not be less than 12" from the ap-

pliance opening.

Figure 5 - Mantel Clearances

FIREPLACE

INSTALLATION

CLEARANCES

Minimum clearances to combustibles are:

• Fireplace ﬂanges to studs . . . . . . . . . . . . . . 0"

• Fireplace back/sides . . . . . . . . . . . . . . . . . . 1"

• Fireplace spacers to framing . . . . . . . . . . . . 0"

• Openings to perpendicular wall . . . . . . . . . 4"

• End glass to facing wall . . . . . . . . . . . . . . 12"

• Side glass to facing wall . . . . . . . . . . . . . . 36"

• Bottom of ﬁreplace to ﬂoor or platform . . . 0"

• “B” vent surfaces . . . . . . . . . . . . . . . . . . . . 1"

• Top of ﬁreplace opening to ceiling . . . . . . 35"

See Figures 3 and 4.

CAUTION: Do not block

required air spaces with insu-

lation or any other material. Do

not obstruct effective opening

of appliance with any type of

facing material.

In selecting a location, the following precautions

must be observed:

1. Do not connect this appliance to a chimney

system used for a solid fuel burning ﬁre-

place.

2. Install in an area providing ventilation and

adequate combustion air.

3. Due to high temperatures, do not locate this

appliance in high trafﬁc areas or near furniture

and draperies.

4. Never obstruct the front opening of the appli-

ance or the ﬂow of combustion and ventilation

air. Keep control compartments accessible.

5. DO NOT locate in the vicinity where gasoline

or other ﬂammable liquids may be stored. The

appliance area must be kept clear and free

from these combustible materials.

SELECTING LOCATION

Continued

1" (22 mm) Minimum

Clearance to Combustibles

1" (22 mm) Minimum

Clearance from Pipes

to Combustibles

4" (102 mm) Min. from the Perpendicular

Side Wall to the Fireplace Opening (Typ.)

6" O.D.

(152 mm)

19"

(483 mm)

11 3/8"

(289 mm)

22 3/4"

(578 mm)

22 1/4"

(565 mm)

35" (889 mm) Min.

to Effective Opening

to Ceiling

Doublewall

6" B-Vent

1" (25 mm) Min. Clearance

from Pipes to Combustibles

Do Not Pack Space

Between Spacer with

Any Type of Insulation

0" to

Floor

Note: Mantel clearances apply

to both sides of the applliacne.

Header

Drywall

Fireplace Top

12 1/4"

(Ref.)

6" (Ref.)

33°

12" Min.

7" Min.

to Effective

Opening

3" Nom.

1 1/2" Max.

Combustible

Materials

www.desatech.com

55173-F 7

FIREPLACE

INSTALLATION

Continued

FRAMING

Construct framing using dimensions shown if

Figures 6, 7 and 8. (Use the ﬁgure applicable to

your application.) Figure 6 shows the framing

dimensions prior to having the appliance in place.

Once the unit has been ﬁtted, bring studs in against

nailing ﬂanges located on the side of the appliance

making sure a 1" clearance is maintained as shown

in Figure 7.

If the ﬁreplace is to be installed directly on carpet-

ing, tile (other than ceramic) or any combustible

material other than wood ﬂooring the ﬁreplace

must be installed upon a metal or wood panel

extending the full width and depth of the ﬁreplace

(see Figure 8). The platform must be solid, ﬂat and

fully supported.

Figure 6 - Framing Dimensions Prior to

Placing Appliance

Figure 7 - Securing Appliance with

Nailing Flanges

Figure 8 - Appliance Must Be Installed

on a Wood or Metal Panel if Being

Installed on Any Combustible Material

Other Than Wood

52 3/4"

(1340 mm)

Min.

46"

(11688 mm)

22 3/4"

(578 mm)

VENT PIPE INSTALLATION

A 6", B-1 type gas vent pipe is a double-wall, vent-

ing system (not supplied) which must be installed

during rough framing of the appliance. Any B-1

type gas vent system may be used for proper vent-

ing as long as the vent system is installed per the

vent manufacturerʼs recommendations.

DESA supplies this appliance with a tapered starter

pipe for a snug ﬁt. Slide B-1 type vent pipe over

this starter pipe until vent pipe is fully seated.

Secure this ﬁrst section of B-vent pipe by strap-

ping the connector around the vent pipe and then

tightening the strap with any 1/8" nut and bolt (see

Figure 9). Note: Visually inspect for proper vent

connection by looking inside top of appliance. If

connection does not appear to be correct, contact

your local service technician.

Figure 9 - Installing B-Vent Pipe

Nailing Flanges

1" Min. to Combustibles

Prepared Framing

Nails or Screws

As Required by Design as

Long as Ceiling Clearances

are Maintained

49" Minimum

(Diagonal)

B-1 Type

Vent (Not

Supplied)

Strap

(Fasten with

#6 Screw or

Bolt)

www.desatech.com 55173-F8

FIREPLACE

INSTALLATION

Continued

OPTIONAL OUTSIDE AIR KIT

(MODEL AK-4)

The installation of an outside air kit should be

completed during the rough framing of the ﬁre-

place due to the nature of it's location. Outside

combustion air is accessed through a vented

crawl space.

CAUTION: Air inlet ducts

must not be terminated in an

attic space.

Avoid installing outside air eyebrow in areas where

inlet opening may be blocked by snow, bushes or

other obstacles (see Figure 10).

The maximum height for the air inlet termination

cannot exceed 3 feet below the B-vent termination

exhaust height.

Figure 10 - Outside Air Kit

Secure to Collars with Duct Tape or

Screws

Air Inlet

Location

Must Allow

For Bushes

or Snow

Vent Hood

Required for

Wall Installation

Air Inlet

Eyebrow

Vented Crawl Space

(Check Local Codes

Before Installing in a

Vented Crawl Space)

MILLIVOLT MODELS (GL36ST/STP)

The installation of a wall switch in this millivolt

control appliance allows you to activate the gas

control valve without the use of normal current.

CAUTION: Do not connect

this millivolt system wall switch

to a regular 120v power source!

Gas valve will be damaged be-

yond repair.

Wall Switch Installation

1. Remove the J-box cover plate from side of

applianceʼs outer surround.

2. Using the 18 ga. millivolt wire and wall switch

(both supplied), connect wiring per wiring

diagram (see Figure 11). For more detail, see

Wiring Diagrams on page 16.

Note: If any of the original 10 feet supplied wire

must be replaced, use Thermostat Millivolt Wire

18 AWG Type CL2-105 C or equivalent only.

IMPORTANT: Do not hook up to standard 120

VAC household wiring.

Figure 11 - Wall Switch Installation

TPTHTP TH

Wall Switch

(Supplied)

Back View

To Thermopile

Route Millivolt Wires

(Supplied) Through

Electrical Conduit Bushing

ELECTRONIC MODELS (GL36STE/EP)

This appliance must be properly wired to standard

120v household current through the DESA-pro-

vided wall switch before its remote control unit

can be used to activate the automatic pilot ignition

(turn ﬁreplace ﬂames ON).

Wall Switch Installation

1. Remove the J-box cover plate from side of

applianceʼs outer surround.

2. Using the 18 ga. wires coming through strain

relief grommet on side of applianceʼs outer

wall to standard household 120 VAC current

through the wall switch provided, as shown in

Figure 12, page 9. For more detail, see Wiring

Diagrams, page 16.

Note: If any of the original 10 feet supplied wire

must be replaced, use 20 AWG electrical wire or

equivalent only.

www.desatech.com

55173-F 9

FIREPLACE

INSTALLATION

Continued

GAS SUPPLY TESTING

Note: This section is intended as a guide for quali-

ﬁed technicians installing gas to this appliance.

CAUTION: Do not connect

appliance before pressure test-

ing gas piping. Damage to gas

valve may result and an unsafe

condition may be caused.

The appliance and its individual shut-off valve

must be disconnected from the gas supply piping

system during any pressure testing of that system at

test pressures in excess of 1/2 psig (3.5 kPa).

The appliance must be isolated from the gas sup-

ply piping system by closing its individual manual

shut-off valve during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 psig (3.5 kPa).

This unit has been tested for installation at high

altitude in accordance with Canadian test stan-

dard CAN/CGA-2.17. Higher altitudes affect the

atmospheric pressure and heat valve of gaseous

fuels. When installing this unit at high altitudes,

the rated input will be lower than at sea level. The

lowered oxygen content in the air and the lowered

gas density require installation of a different size

oriﬁce in order to achieve clean combustion of

the unit. Consult the unit data plate for the proper

high-altitude oriﬁce size. Fill out the information

sticker attached to the unit when ﬁeld converting.

See Speciﬁcations, page 15, when derating.

The gas control valve is secured to the burner pan

assembly underneath the front ledge. A 1/8" NPT

plugged tapping is provided on the gas control

valve for a test gauge connection immediately

upstream of the gas supply connection to the ap-

pliance (see Figures 13 and 14).

Figure 12 - Wiring Through Outer Surround

Figure 13 - Millivolt Control Valve

Figure 14 - Electronic Control Valve

ON/OFF

Knob

Pilot

Adjustment

Cap

Pilot Gas Line

Do Not Kink

Inlet

Pressure

Outlet

Pressure

To Main

Burner

To Pilot

Burner

From

Gas

Supply

Main

Burner

Inlet

Pressure

Outlet

Pressure

GAS LINE HOOK-UP

WARNING: Gas line hookup

should be done by your gas

supplier or a qualiﬁed service

person.

WARNING: Before you pro-

ceed, make sure your gas supply

is OFF.

A manual shutoff valve has been included in the

applianceʼs gas supply system. You may consider

installing an extra gas shutoff valve outside the ap-

plianceʼs enclosure (check with local codes) where

it can be accessed more conveniently with a key

through a wall as shown in Figure 15, page 10.

A 30" long, 1/2" NPT SCHD 40 ﬂexible gas line

(supplied) may be used between the incoming 1/2"

NPT black iron gas line and the ﬁreplace regulator

(located inside the ﬁrebox, under the access plate).

The incoming gas line may be routed toward the

appliance from either the left or right hand side of

ﬁreplace outer surround.

Common

Ground Wire

Strain Relief

Grommet

www.desatech.com 55173-F10

To install:

1. Remove gas line cover plate from applianceʼs

outer surround at the location to be used.

2. Remove insulation from inside the gas line

conduit sleeve.

3. Run gas line through sleeve.

4. Prepare incoming black iron gas line with

Teﬂon tape or pipe joint compound. (Check

local codes as to the use of Teﬂon tape.)

CAUTION: Compounds used

on threaded joints of gas piping

shall be resistant to the action

of Liqueﬁed Petroleum (LP or

propane) and should be applied

lightly to ensure excess sealant

does not enter the gas line.

5. Connect incoming gas line to regulator. Secure

all joints tightly with wrench, but do not over

tighten. If a ﬂexible gas line is used, take care

not to kink the connector.

6. Re-pack insulation in and around the conduit

sleeve and ﬂexible gas line.

WARNING: All gas piping

and connections must be tested

for leaks after the installation is

completed.

After ensuring that the gas valve

is on, apply a commercial leak

detection solution to all con-

nections and joints. If bubbles

appear, leaks can be detected

and corrected.

Do not use an open ﬂame for leak

testing and do not operate any

appliance if a leak is detected.

Typical Exterior Wall Gas

Shutoff Installation

Key

Extension

Shutoff

Valve

FIREPLACE

INSTALLATION

Continued

Figure 15 - Typical Exterior Wall Gas

Shut-Off Installation

LOG SET PLACEMENT

Carefully remove log set from packaging. Place

the two bottom logs over grate and align with pins.

Place three loose logs, or twigs, onto alignment

pins on two bottom logs (see Figure 16).

Figure 16 - Log Placement

FIREPLACE FACING

Any non-combustible material may be used for

facing (glass, tile, brick, etc.) as long as the proper

clearances are adhered to and the ﬁreplace open-

ings are not blocked or obstructed in any way. See

Clearances, page 6, and Figure 17 on page 11.

Use only heat-resistant, noncombustible mortar

or adhesive when securing facing material to the

front of the ﬁreplace.

Bottom Logs

Top Logs (Twigs)

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa Variable Manually-Controlled Models Quick start guide

Desa

Desa VTGF33PRA Quick start guide

Desa

Desa B36 User manual

Desa

Desa H) Quick start guide

Desa

Desa VDCFTNB Quick start guide

Desa

Desa V036NR Series Quick start guide

Desa

Desa VT32N Series Quick start guide

Desa

Desa Vanguard VVSR18 Quick start guide

Desa

Desa CVDA24M User manual

Desa

Desa VTC36PE SERIES Quick start guide

Desa

Desa V42V-A Quick start guide

Desa

Desa CDCFNR Quick start guide

Desa

Desa Vanguard VI33NRA Quick start guide

Desa

Desa VK42N SERIES Quick start guide

Desa

Desa Tudor VT36NA Series Quick start guide

Desa

Desa Wood burning fireplace Assembly instructions

Desa

Desa K42EN Series Quick start guide

Desa

Desa (V)UM36SR Quick start guide

Desa

Desa Comfort Glow CGFP28P User manual

Desa

Desa C36EMW User manual

Desa

Desa LMFP33NR(A) Quick start guide

Desa

Desa VI33NR Quick start guide

Desa

Desa Victorian V42EN-A Series Quick start guide

Desa

Desa FVMR18 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions