Desa Vanguard VMH26TPC Quick start guide

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediatelycallyourgassupplierfromaneighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a quali-

fied installer, service agency, or the gas supplier.

MODELS VMH26TPC AND VMH26TNC

14,000 to 26,000 Btu/Hr with Thermostat

VENT-FREE COMPACT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

Shown with Optional Cabinet Mantel/Hearth Base Accessory

www.desatech.com 113111-01B

WARNING: Improper installation, adjustment, altera-

tion, service, or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualified installer, service

agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses

air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air

must be provided. Refer to

Air for Combustion and

Ventilation

section on page 6 of this manual.

This appliance may be installed in an aftermarket,*

permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the

manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Local Codes ........................................................ 4

Product Identification .......................................... 4

Product Features ................................................ 5

Unpacking ........................................................... 5

Assembly ............................................................ 5

Air for Combustion and Ventilation ...................... 6

Installation ........................................................... 9

Operating Fireplace .......................................... 19

Inspecting Burner .............................................. 21

Cleaning and Maintenance ............................... 22

Troubleshooting ................................................ 23

Specifications .................................................... 27

Service Hints ..................................................... 27

Technical Service .............................................. 27

Replacement Parts ........................................... 27

Illustrated Parts Breakdown and Parts List ....... 28

Accessories ....................................................... 30

Warranty Information .......................... Back Cover

www.desatech.com

113111-01B 3

SAFETY INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects,

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, oper-

ate, or service this fireplace. Im-

proper use of this fireplace can

cause serious injury or death

from burns, fire, explosion, elec-

trical shock, and carbon mon-

oxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of car-

bon monoxide poisoning resemble the flu, with head-

aches, dizziness, or nausea. If you have these signs,

the fireplace may not be working properly. Get fresh

air at once! Have fireplace serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the influence

of alcohol, and those at high altitudes.

Natural and Propane/LP Gas:

Natural and propane/LP

gases are odorless. An odor-making agent is added to

these gases. The odor helps you detect a gas leak.

However, the odor added to the gas can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guide to safe and proper operation of this fireplace.

WARNING: Any change to

this heater or its controls can be

dangerous.

WARNING: Do not allow fans

to blow directly into the fireplace.

Avoid any drafts that alter burner

flame patterns. Ceiling fans can

create drafts that alter burner

flame patterns. Altered burner

patterns can cause sooting.

WARNING: Do not use a

blower insert, heat exchanger

insert, or other accessory not

approved for use with this fire-

place.

Due to high temperatures, the

appliance should be located out

of traffic and away from furni-

ture and draperies.

Do not place clothing or other

flammable material on or near

the appliance. Never place any

objects in the fireplace.

Fireplace front and screen be-

come very hot when running fire-

place. Keep children and adults

away from hot surfaces to avoid

burns or clothing ignition. Fire-

place will remain hot for a time

after shutdown. Allow surfaces

to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with fireplace.

You must operate this fireplace

with the fireplace screen and

hood in place. Make sure fire-

place screen is in place before

running fireplace.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline, and other flam-

mable vapors and liquids.

1. This appliance is only for use with the type of

gas indicated on the rating plate. This appli-

ance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors (propane/LP only).

www.desatech.com 113111-01B

SAFETY INFORMATION

Continued

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• if you cannot reach your gas supplier, call

the fire department

4. This fireplace shall not be installed in a bed-

room or bathroom.

5. Do not use this fireplace as a wood-burning

fireplace. Use only the logs provided with the

fireplace.

6. Do not add extra logs or ornaments such as

pine cones, vermiculite, or rock wool. Using

these added items can cause sooting. Do not

add lava rock around base. Rock and debris

could fall into the control area of fireplace.

7. This fireplace is designed to be smokeless. If

logs ever appear to smoke, turn off fireplace

and call a qualified service person.

Note:

Dur-

ing initial operation, slight smoking could

occur due to log curing and fireplace burning

manufacturing residues.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 22.

9. Before using furniture polish, wax, carpet

cleaner, or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

10. This fireplace needs fresh air ventilation to

run properly. This fireplace has an Oxygen

Depletion Sensing (ODS) safety shutoff sys-

tem. The ODS shuts down the fireplace if not

enough fresh air is available. See Air for Com-

bustion and Ventilation, pages 6 through 8. If

fireplace keeps shutting off, see Troubleshoot-

ing, pages 23 through 26.

11. Do not run fireplace

• where flammable liquids or vapors are used

or stored.

• under dusty conditions.

12. Do not use this fireplace to cook food or burn

paper or other objects.

13. Do not use fireplace if any part has been under

water. Immediately call a qualified service tech-

nician to inspect the room fireplace and to re-

place any part of the control system and any

gas control which has been under water.

14. Turn off and unplug fireplace and let cool be-

fore servicing. Only a qualified service per-

son should service and repair fireplace.

15. Operating fireplace above elevations of 4,500

feet could cause pilot outage.

16. Do not operate fireplace if any log is broken.

Do not operate fireplace if a log is chipped

(dime-sized or larger).

17. To prevent performance problems, do not use

propane/LP fuel tank of less than 100 lbs. ca-

pacity (propane/LP only).

18. Provide adequate clearances around air

openings.

LOCAL CODES

Install and use fireplace with care. Follow all lo-

cal codes. In the absence of local codes, use the

latest edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT

IDENTIFICATION

Figure 1 - Vent-Free Gas Compact

Fireplace

Ignitor Button

Screen

Fireplace

Cabinet

Logs

Control Knob

www.desatech.com

113111-01B 5

PRODUCT FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

fireplaces. The ODS/pilot shuts off the fireplace

if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This system re-

quires no matches, batteries, or other sources to

light fireplace.

THERMOSTATIC HEAT CONTROL

This fireplace has a thermostat sensing bulb and a

control valve. The thermostat will automatically

modulate the heat output to maintain a consistent

room temperature. This results in greater fireplace

comfort. This can also result in lower gas bills.

UNPACKING

1. Remove fireplace and hood from carton. Log

is wrapped and inside fireplace. Do not re-

move at this time.

2. Remove all protective packaging applied to

fireplace for shipment.

3. Make sure your fireplace includes one hard-

ware packet.

4. Check fireplace for any shipping damage. If

fireplace is damaged, promptly inform dealer

where you bought fireplace.

ASSEMBLY

WARNING: Always have

branch support and screen in

place before operating fireplace.

This prevents excessive tem-

peratures on fireplace surfaces.

WARNING: Failure to position

theparts inaccordancewiththese

diagrams or failure to use only

parts specifically approved with

this fireplace may result in prop-

erty damage or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

• Phillips screwdriver

• 5/16" hex wrench

• slotted screwdriver

Installing Log

1. Lift screen up and pull out to remove.

2. Cut two plastic straps to remove the log from

the firebox cavity.

An optional blower is available. See Accessories,

page 30. Install optional blower now. Follow in-

stallation instructions provided with blower.

4. Remove log packaging material and discard

packaging. Gently place log set on burner sup-

port (see Figure 2). The log should fit flat

against top of burner support and log locator

tabs fit into the slots under the log. Do not

allow log to contact flame. If flame contacts

log, soot will be created.

Figure 2 - Assembling Fireplace

Log

Screen

Burner Support

with Log

Locator Tabs

Branch

Support

Shoulder

Screw

www.desatech.com 113111-01B

ASSEMBLY

Continued

5. Reattach screen by placing the notches in the

screen frame over the shoulder screws and

pushing down.

Assembling Hood

1. Locate four black phillips sheet metal screws

from the hardware packet.

2. Rotate hood as shown in Figure 3. Make sure

hood tabs point toward fireplace.

3. Insert hood tabs between baffle and louvers

(see Figure 3).

4. Gently rotate hood to upright position. Make

sure hood tabs are behind louvers and hood is

resting on firebox top (see Figure 3).

5. Align screw holes on hood with screw holes

on firebox top.

6. Insert screws as shown in Figure 3. Tighten

screws firmly.

Figure 3 - Assembling Hood

Hood

Louver

Hood Tab

Baffle

Sheet Metal

Screw

Firebox Top

Hood Tabs

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

notbe installedin aconfinedspace

or unusually tight construction

unless provisions are provided

foradequate combustion andven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efficient than

ever. New materials, increased insulation, and new

construction methods help reduce heat loss in

homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy effi-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code,ANSI Z223.1/ NFPA 54, Section 5.3, Air

for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 6 through 8 will help

you classify your space and provide adequate ven-

tilation.

Unusually Tight Construction

The air that leaks around doors and windows may

provide enough fresh air for combustion and ven-

tilation. However, in buildings of unusually tight

construction, you must provide additional fresh air.

www.desatech.com

113111-01B 7

Unusually tight construction is defined as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10-11 kg per pa-sec-m2)

or less with openings gasketed or

sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to ar-

eas such as joints around window and

door frames, between sole plates and

floors, between wall-ceiling joints, be-

tween wall panels, at penetrations for

plumbing, electrical, and gas lines, and

at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh

air. See

Ventilation Air From Outdoors

page 8.

If your home does not meet all of the three

criteria above, proceed to

Determining

Fresh-Air Flow For Fireplace Location

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1.3/

NFPA 54 defines a confined space as a space whose

volume is less than 50 cubic feet per 1,000 Btu

per hour (4.8 m3per kw) of the aggregate input

rating of all appliances installed in that space and

an unconfined space as a space whose volume is

not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3per kw) of the aggregate input rating of all

appliances installed in that space. Rooms commu-

nicating directly with the space in which the ap-

pliances are installed*, through openings not fur-

nished with doors, are considered a part of the un-

confined space.

* Adjoining rooms are communicating only if there

are doorless passageways or ventilation grills be-

tween them.

AIR FOR COMBUSTION

AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Confined or

Unconfined Space

Use this work sheet to determine if you have a

confined or unconfined space.

Space: Includes the room in which you will install

fireplace plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example:

Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft. (vol-

ume of space)

If additional ventilation to adjoining room is sup-

plied with grills or openings, add the volume of

these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example:

2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free fireplace __________ Btu/Hr

Gas water heater* __________ Btu/Hr

Gas furnace __________ Btu/Hr

Vented gas heater __________ Btu/Hr

Gas fireplace logs __________ Btu/Hr

Other gas appliances* + __________ Btu/Hr

Total = __________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater ______________ Btu/Hr

Vent-free fireplace ______________ Btu/Hr

Total ______________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

________

Btu/Hr (maximum the space can support)

________

Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space

can support)

56,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a confined space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must pro-

vide additional fresh air. Your options are as follows:

30,000

+ 26,000

= 56,000

www.desatech.com 113111-01B

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an uncon-

fined space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors.

C. Install a lower Btu/Hr fireplace, if lower Btu/Hr

size makes room unconfined.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an uncon-

fined space. You will need no additional fresh air ven-

tilation.

WARNING: If the area in

which the heater may be oper-

ated is smaller than that defined

as an unconfined space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the

National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section

5.3

or applicable local codes

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

confined space. When ventilating to an adjoining

unconfined space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the floor on the wall connecting

the two spaces (see options 1 and 2, Figure 4).

You can also remove door into adjoining room (see

option 3, Figure 4). Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills

or ducts. You must provide two permanent open-

ings: one within 12" of the ceiling and one within

12" of the floor. Connect these items directly to

the outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-con-

trolled power vent. Heated air entering the attic

will activate the power vent.

Figure 5 - Ventilation Air from Outdoors

Shown with Optional Mantel

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Figure 4 - Ventilation Air from Inside

Building Shown with Optional Mantel

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

www.desatech.com

113111-01B 9

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualified ser-

vice person must install fire-

place. Follow all local codes.

WARNING: Never install the

fireplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objects are less than 36 inches

from the front, top, or sides of

the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: This fireplace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to fireplace. Install-

ing fireplace next to vinyl or cloth

wall coverings or operating fire-

place where impurities (such as,

but not limited to, tobacco

smoke, aromatic candles, clean-

ing fluids, oil or kerosene lamps,

etc.) in the air exist, may dis-

color walls or cause odors.

IMPORTANT:

Vent-free fireplaces add moisture

to the air. Although this is beneficial, installing

fireplace in rooms without enough ventilation air

may cause mildew to form from too much mois-

ture. See Air for Combustion and Ventilation, pages

6 through 8.

Note:

Your Vanguard fireplace is designed to be

used in zero clearance installations. Wall or fram-

ing material can be placed directly against any

exterior surface of your fireplace, except where

standoff spacers are integrally attached. If stand-

off spacers are attached to your fireplace, these

spacers can be placed directly against wall or fram-

ing materials.

Use the dimensions shown for rough openings to

create the easiest installation (see Built-In Fire-

place Installation, page 10).

CHECK GAS TYPE

Use only the correct type of gas (natural or pro-

pane/LP). If your gas supply is not the correct gas

type, do not install heater. Call dealer where you

bought heater for proper type heater.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

INSTALLATION ITEMS

Before installing fireplace, make sure you have

the items listed below.

• external regulator - propane/LP only (supplied

by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection*

• ground joint union

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certified equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. Purchase the optional CSA

design-certified equipment shutoff valve from your

dealer. See Accessories, page 30.

Note:

If desired, purchase a four-sided trim kit for

built-in installations. See Accessories, page 30.

www.desatech.com 113111-01B

LOCATING FIREPLACE

WARNING: Maintain the

minimum clearances shown in

Figures 6 and 7. If you can, pro-

vide greater clearances from

floor, ceiling, and joining wall.

You can recess firebox into the wall. You can also

position fireplace in the optional cabinet or cor-

ner mantels.

IMPORTANT:

Only use optional

cabinet or corner mantels specified in this manual.

Purchase the optional mantel from your dealer (see

Accessories, page 30).

INSTALLATION

Continued

Figure 7 - Mounting Clearances As

Viewed From Front of Fireplace Shown

with Optional Mantel

Top Of

Mantel Can

Be Flush

With Wall

Left

Side

CEILING

Right

Side

36"

Minimum

From

Sides Of

Fireplace

Left

Side

CEILING

36"

Minimum

FLOOR

Right

Side

0" Minimum

To Top

Surface Of

Carpeting,

Tile Or Other

Combustible

Material

0" Minimum

To Top

Surface Of

Carpeting,

Tile Or Other

Combustible

Material

Figure 6 - Mounting Clearances As

Viewed From Front of Fireplace Shown

Built-In the Wall

Note:

When installing fireplace directly on car-

peting, tile or other combustible material, other

than wood flooring, the fireplace shall be installed

on a metal or wood panel extending the full width

and depth of the fireplace.

CAUTION: If you install the

fireplace in a home garage

• fireplace pilot and burner must

beat least18inches abovefloor.

• locate fireplace where moving

vehicle will not hit it.

For convenience and efficiency, install fireplace

• where there is easy access for operation, inspec-

tion, and service.

• in coldest part of room.

An optional blower kit is available from your dealer

(see Accessories, page 30). If planning to use

blower, locate fireplace near an electrical outlet.

BUILT-IN FIREPLACE

INSTALLATION

Built-in installation of this fireplace involves in-

stalling fireplace into a framed-in enclosure. This

makes the front of fireplace flush with wall. An

optional trim kit accessory is available (see Ac-

cessories, page 30). Trim will extend past sides of

fireplace approximately 1/2 inch. This will cover

the rough edges of the wall opening. If installing

a built-in mantel above the fireplace you must fol-

low the clearances shown in Figure 11, page 12.

Follow the instructions below to install the fire-

place in this manner.

Actual Framing

Height 26" 26 7/8"

Front Width 26 3/4" 26 7/8"

Depth 9 1/2" 10 1/2"

Bottom 3/4" 3/4"

1. Frame in rough opening. Use dimensions

shown in Figure 8, page 11, for the rough

opening.

If installing in a corner, use dimensions shown

in Figure 9, page 11, for the rough opening.

The height is 26 7/8" which is the same as the

wall opening above.

Other manuals for Vanguard VMH26TPC

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa Vanguard VI33NRA Quick start guide

Desa

Desa Comfort Glow GCF26PR Quick start guide

Desa

Desa Comfort Glow CGFB32CB Original instructions

Desa

Desa Comfort Glow CVTR18 Quick start guide

Desa

Desa SDVBNC Quick start guide

Desa

Desa GA3700 Quick start guide

Desa

Desa VV42ENA1 Series Quick start guide

Desa

Desa Comfort Glow LFP33PRA Quick start guide

Desa

Desa CGEFP33PRB Quick start guide

Desa

Desa BVC-36Y Quick start guide

Desa

Desa VTC36N Series Quick start guide

Desa

Desa Vanguard EVGL850N Quick start guide

Desa

Desa VV36P Series Quick start guide

Desa

Desa VT32EN Series Quick start guide

Desa

Desa TC36N Series Quick start guide

Desa

Desa CDCFPR Quick start guide

Desa

Desa M42E(B Quick start guide

Desa

Desa Comfort Glow CHDV37N Quick start guide

Desa

Desa VSGF33PRC Quick start guide

Desa

Desa CEF26-3 User manual

Desa

Desa VICTORIAN V36EN-A Series Quick start guide

Desa

Desa VT32N Series Quick start guide

Desa

Desa CDCFTNA User manual

Desa

Desa VYGF33NR Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions