Desa M36E(B Quick start guide

NATURAL GAS MODELS

M36E(B,H), M42E(B,H),

VM36E(B,H) AND VM42E(B,H)

PROPANE/LP GAS MODELS

M36EP(B,H), M42EP(B,H),

VM36EP(B,H) AND VM42EP(B,H)

B-VENT DECORATIVE ELECTRONIC IGNITION GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

For more information, visit www.desatech.com

FOR YOUR SAFETY

— Donotstoreorusegasolineoranyotherammable

vapors or liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS :

• Donottrytolightanyappliance.

• Donottouchanyelectricalswitch;

• Donotuseanyphoneinyourbuilding.

• Immediatelycallyourgassupplierfromaneighbor’s

phone.Followthegassupplier’sinstructions.

• Ifyoucannotreachyourgassupplier,callthere

department.

— Installationandservicemustbeperformedbyaquali-

edinstaller,serviceagencyorthegassupplier.

INSTALLER:Leavethismanualwiththeappliance.

CONSUMER:Retainthismanualforfuturereference.

WARNING:Iftheinformationintheseinstructions

isnotfollowedexactly,areorexplosionmayresult

causingpropertydamage,personalinjuryordeath.

O-TL REPORT # 114-F-16-4

www.desatech.com 108796-01T2

 WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause injury or

propertydamage.Refertothismanualforcorrectin-

stallation and operational procedures. For assistance

or additional information consult a qualied installer,

service agency or the gas supplier.

NOT FOR USE WITH SOLID FUEL

CHECK LOCAL CODES PRIOR TO INSTALLATION

SAVE THIS BOOK

Thisbookisvaluable.Inadditiontoinstructingyouon

howtoinstallandmaintainyourappliance,italsocon-

tainsinformationthatwillenableyoutoobtainreplace-

mentpartsoroptionalaccessoryitemswhenneeded.

Keepitwithyourotherimportantpapers.

Thisappliancemaybeinstalledinanaftermarket*,per-

manentlylocated,manufactured(mobile)home,where

notprohibitedbystateorlocalcodes.

Thisapplianceisonlyforusewiththetypeofgasindi-

cated on the rating plate.

This appliance is not convertible for use with other

gases,unlessacertiedkitisused.

*Aftermarket:Completionofsale,notforpurposeofresale,fromthemanufacturer.

StateofMassachusetts:Theinstallationmustbemade

byalicensedplumberorgastterintheCommonwealth

of Massachusetts.

TABLE OF CONTENTS

Safety .................................................................. 3

Unpacking............................................................ 4

Introduction.......................................................... 4

Selecting Location ............................................... 5

Product Specications......................................... 6

PreInstallation Preparation .................................. 7

Venting Installation .............................................. 9

Installation ..........................................................11

Operation........................................................... 18

Inspecting Burners............................................. 19

Cleaning and Maintenance................................ 20

Replacement Parts............................................ 20

Wiring Diagram.................................................. 21

Service Hints ..................................................... 21

Technical Service............................................... 21

Troubleshooting................................................. 22

Parts .................................................................. 24

Accessories ....................................................... 29

Warranty ..............................................Back Cover

www.desatech.com

108796-01T 3

SAFETY

WARNING: This product con-

tainsand/orgenerateschemicals

knowntotheStateofCalifornia

tocausecancerorbirthdefects

orotherreproductiveharm.

IMPORTANT:Readthisowner’s

manualcarefullyandcompletely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

cancauseseriousinjuryordeath

from burns, re, explosions,

electrical shock and carbon

monoxidepoisoning.

DANGER:Carbonmonoxide

poisoningmayleadtodeath!

This replace is a vented product. This replace

will not produce any gas leakage into your home

if properly installed. This replace must be

properly installed by a qualied service person.

If this unit is not properly installed by a qualied

service person, gas leakage can occur.

CarbonMonoxidePoisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness or nausea. If you

have these signs, the replace may not have

been installed properly. Getfreshairatonce!

Have replace inspected and serviced by a

qualied service person. Some people are more

affected by carbon monoxide than others. These

include pregnant women, people with heart or

lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

Propane/LP gas and natural gas are both

odorless. An odor-making agent is added

to each of these gases. The odor helps you

detect a gas leak. However, the odor added

to these gases can fade. Gas may be present

even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

thisreplaceoritscontrolscan

bedangerous.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases unless a certied kit is used.

2. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier's instructions

• if you cannot reach you gas supplier, call

the re department.

4. Never install the replace

• in a recreational vehicle

• where curtains, furniture, clothing or other

ammable objects are less than 36" from

front and 42" from top of replace. For

side clearances see Figure 6, page 7

• in high trafc areas

• in windy or drafty areas

5. This replace reaches high temperatures.

Keep children and adults away from hot

surfaces to avoid burns or clothing igni-

tion. Fireplace will remain hot for a time

after shutdown. Allow surfaces to cool

before touching.

6. Carefully supervise young children when

they are in the room with replace.

7. A hearth extension is not required with this

appliance. If one is installed, it is for aes-

thetic purposes only and does not have

to meet the standard requirements.

8. Turn replace off and let cool before ser-

vicing or repairing. Only a qualied service

person should install, service or repair

this replace. Have replace inspected

annually by a qualied service person.

9. You must keep control compartments,

burners and circulating air passages clean.

More frequent cleaning may be needed due

to excessive lint and dust from carpeting,

bedding material, etc. Turn off the gas valve

and pilot light before cleaning replace.

10. Have venting system inspected annually by

a qualied service person. If needed, have

venting system cleaned or repaired. See

Cleaning and Maintenance, page 20.

www.desatech.com 108796-01T4

11. Keep the area around your replace clear

of combustible materials, gasoline and

other ammable vapor and liquids. Do

not run replace where these are used or

stored. Do not place items such as clothing

or decorations on or around replace.

12. Do not use this replace to cook food or

burn paper or other objects.

13. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this replace.

Use only the gas type indicated on re-

place nameplate.

14. This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the National Electrical Code,

ANSI/NFPA 70 or the Canadian Electrical

Code, CSA C22.1.

15. Do not obstruct the ow of combustion

and ventilation air in any way. Provide

adequate clearances around air open-

ings into the combustion chamber along

with adequate accessibility clearance for

servicing and proper operation.

16. Do not install replace directly on carpet-

ing, vinyl tile or any combustible material

other than wood. The replace must set

on a metal or wood panel extending the

full width and depth of the replace.

17. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

18. Do not operate replace if any log is

broken.

19. Do not use a blower insert, heat exchang-

er insert or other accessory not approved

for use with this replace.

20. Provide adequate clearances around air

openings.

SAFETY

Continued

UNPACKING

The following items are packed inside the

rebox. Remove before positioning rebox

into framing.

• Transition Collar - For vent connection

• Ceramic Log Pack - Shrink-wrapped on

cardboard

• Three (3) plastic bags containing lava rock,

pan and ember materials

• Rear Log - Remove two plastic quick ties

from around burner and grate

• Grate Stand - Lift off of burner pan

Check all items for any shipping damage. If

damaged, promptly inform dealer or distributor

where you bought the product.

Safely retain these items for later installation.

INTRODUCTION

Models M36E(P)(B,H), VM36E(P)(B,H),

M42E(P)(B,H) and VM42E(P)(B,H) are vented

gas replaces that use an electronic control

valve and electronic ignition system. A 6" B-Type

venting system and a listed type vent cap are not

supplied but are required for proper operation.

See venting instructions on pages 9 and 10.

WARNING: This gas appli-

ancemustnotbeconnectedto

achimneyueservicingasolid

fuelburningappliance.

Models M36E(B,H), VM36E(B,H), M42E(B,H)

and VM42E(B,H) are factory equipped for use

with natural gas and must be converted when

intended for use with propane/LP gas. A respec-

tive model PCBE-36 or PCBE-42 conversion

kit may be purchased for simple conversion to

propane/LP gas. See Accessories, page 29.

BEFORE YOU BEGIN

Before beginning the installation of your

appliance, read these instructions through

completely.

This DESA Heating, LLC appliance and its

approved components are safe when installed

according to this installation manual and are

operated as recommended by DESA Heating,

LLC. Unless you use DESA Heating, LLC ap-

proved components tested for this appliance,

YOUMAYCAUSEAFIREHAZARD!

The DESA Heating, LLC warranty will be

voided by and DESA Heating, LLC disclaims

any responsibility for the following actions:

A) Modication of the appliance or any of the

components.

B) Use of any component part not approved

by DESA Heating, LLC in combination

with this appliance.

C) Installation and/or operation in a manner

other than instructed in this manual.

The burning of anything other than the type of

gas approved for use in this gas appliance.

www.desatech.com

108796-01T 5

The installation must conform with local codes

or, in the absence of local codes, with the cur-

rent National Fuel Gas Code, ANSI Z223.1/

NFPA 54. This appliance complies with ANSI

Z21.50/CSA 2.22.

WARNING: Installation of this

appliance should be done by

a qualied service person well

trained in the installation of such

appliances.Youwillalsoneeda

building permit from your local

BuildingandSafetyCommission-

erbeforeinstallingthisappliance;

otherwiseyourinsuranceco.may

not cover this appliance.

NOTICE: This appliance is not

intendedtobeusedasaprimary

source of heat.

Figure 1 - Possible Locations for

Installing Appliance

INTERNAL WALL

INSTALLATION

CORNER

INSTALLATION

FULL

PROJECTION

INSTALLATION

FLUSH

INSTALLATION

CAUTION: Do not connect

appliancebeforepressuretest-

inggaspiping.Damagetogas

valvemayresultandanunsafe

conditionmaybecaused.

The appliance and it’s individual shutoff valve

must be disconnected from the gas supply

piping system during any pressure testing of

that system at test pressures in excess of 1/2

psig (3.5 kPa).

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure

testing of the gas supply piping system at

test pressures equal to or less than 1/2 psig

(3.5 kPa).

For the purpose of input adjustment two

pressure taps (for IN and OUT pressures)

are provided on the gas control valve for test

gauge connections to the appliance.

INTRODUCTION

Continued

SELECTING LOCATION

To determine the safest and most efcient

location for your appliance, you must take into

consideration the following guidelines:

1. The location must allow for proper clear-

ances (see Clearances, page 7).

2. Consider a location where heat output

would not be affected by drafts, air con-

ditioning ducts, windows or doors.

3. A location that avoids the cutting of joists

or roof rafters will make installation easier.

Figure 1 shows a plan view of a few com-

mon locations.

Flush installations are recommended where

living space is limited or at a premium and

since the space required to enclose the ap-

pliance would be located beyond an outside

wall, this would also reduce the cutting of

joists, roof rafters and such. Check local

codes for any restrictions.

Projected installations can extend any

distance into the room. A projection may

be ideal for a new addition on an existing,

nished wall.

Corner installations make use of space

that may not normally be used and provides

a wider and more efcient range for radiant

heat transference.

Internalwallinstallations provide a discreet

option for room separation and can also be

ideal as an addition to an existing wall.

www.desatech.com 108796-01T6

PRODUCT SPECIFICATIONS

Outside Air

Kit Location

(Optional)

13.5"

1.5"

Glass Door

(Optional)

Alternate Gas

Supply Inlet

Stand Off

Collar

For Use With

6"Ø Type B-1

Ve nt Pipe Only

DIMENSIONS

HEARTH AREA

Figure 2 - Appliance Dimensions

GAS RATING - NATURAL

M36E(B,H),VM36E(B,H) M42E(B,H),VM42E(B,H)

Max. Input Rating: 40,000 Btu/Hr 45,000 Btu/Hr

Manifold Pressure: 3.5" WC (.87 kPa) 3.5" WC (.87 kPa)

Minimum Supply Pressure: 4.5" WC (1.12 kPa) 4.5" WC (1.12 kPa)

Maximum Supply Pressure: 10.5" WC (2.66 kPa) 10.5" WC (2.66 kPa)

Orice Size: # 30 # 29

GAS RATING - PROPANE/LP

M36P(B,H),VM36P(B,H) M42P(B,H),VM42P(B,H)

Max. Input Rating: 40,000 Btu/Hr 45,000 Btu/Hr

Manifold Pressure: 10" WC (2.49 kPa) 10" WC (2.49 kPa)

Minimum Supply Pressure: 11" WC (2.74 kPa) 11" WC (2.74 kPa)

Maximum Supply Pressure: 13" WC (3.23 kPa) 13" WC (3.23 kPa)

Orice Size: # 52 # 50

Model 36 Model 42 Model 36 Model 42 Model 36 Model 42

A29" 36" I 40 1/4"44 1/4"Q 13 7/8" 14"

B 5/8" 5/8" J21" 24" R 10 1/2"12 1/2"

C41" 48" K 8" 9" S 2 1/2"2 1/2"

D12" 14" L 34 3/4" 42" T 8 1/8"8 1/8"

E 21 1/4" 23" M42" 49" U11" 12 3/4"

F 22 1/4" (24" w/o Brick) 29 1/4" (31" w/o Brick) N36" 40" V7" 7"

G32 5/8" (34" w/o Brick) 39 1/2" (41 1/4" w/o Brick) O37" 41" W 2 1/4"2 1/4"

H 15 3/4" (16 3/4" w/o Brick) 17 3/4" (18 3/4" w/o Brick) P 8 5/8"10 1/2"X5" 4 1/2"

www.desatech.com

108796-01T 7

PREINSTALLATION PREPARATION

Figure 3 - Minimum Clearances

(Top View)

0" Clearance

Nailing

Flange

Front Face

Left Side

Surround

Back

Drywall

2 x 4 Stud

Figure 4 - Minimum Clearances

(Front View)

42" (106.7 cm)

Min. Clearance

from Opening to

Ceiling 0" Clearance

Ceiling

1" (2.5 cm)

Min. Clearance

to "B" Vent's

Outer Pipe

Maintain 2" (5.1 cm)

Min. Clearance to

Transition Pipe as

Measured at Outer

Ve nt Collar

Required air

spaces are

indicated with

an "

". Do not

pack with

insulation or

any other

material.

DO NOT BLOCK

OR OBSTRUCT

OPENINGS

0" Clearance to

Combustible or

Noncombustible

Flooring

MANTEL CLEARANCES AND WALL

DETAILS

A combustible mantle shelf maybe installed a

maximum 12" (22.9 cm) from wall. Figures 5

and 6 show the minimum allowable distances

from various combustible mantle components

in relation to replace opening.

Spacer

3" (7.6 cm)

(3.8 cm) Max.

6" (15.2 cm)

12"

(22.9 cm)

Combustible

Materials

Header

Figure 5 - Mantel Clearances - Side View

(Cross Section)

1 1/2"

(3.8 cm)

Max. 3" (7.6 cm)

Max.

6" (15.2 cm)

Max. A

Outer Surround Combustible

Material May

Be Used

TOP VIEW

SAFE

ZONE

Perpendicular

Wall

Figure 6 - Side Clearances - Top View

(Cross Section)

CLEARANCES

Minimum clearances to combustibles are:

Back and Sides of Outer Surround 0" min.

Drywall to Sides of Front Face

(Nailing Flanges) 0" min.

“B” Vent Surfaces 1" min.

Ceiling to Opening 42" min.

Floor 0" min.

Perpendicular Wall See Figure 6

 CAUTION: Do not block

required air spaces with insu-

lationoranyothermaterial.Do

not obstruct effective opening

of appliance with any type of

facingmaterial.

M36E(B,H),

M36EP(B,H)

VM36E(B,H),

VM36EP(B,H)

M42E(B,H),

M42EP(B,H)

VM42E(B,H),

VM42EP(B,H)

A14" (35.6 cm) 15" (38 cm)

B 8" (20.3 cm) 9" (22.9 cm)

M36E(B,H),

M36EP(B,H)

VM36E(B,H),

VM36EP(B,H)

M42E(B,H),

M42EP(B,H)

VM42E(B,H),

VM42EP(B,H)

A9" (22.9 cm) 6" (15.2 cm)

B 12" (30.5 cm) 9" (22.9 cm)

www.desatech.com 108796-01T8

PREINSTALLATION PREPARATION

Continued

FRAMING

1. Frame appliance enclosure as illustrated

in Figures 7 and 8.

Note: If a wall covering is used to line

enclosure, then all measurements must

be from surface of covering.

2. Place appliance into framing and se-

cure.

Note: If appliance is to be raised above

oor level, a platform must be built to

support appliance.

3. Install supply line to appliance using a 1/2"

NPT black iron gas line terminating 2 5/16"

above bottom of appliance. The gas line

must be installed through lower left side

access point or alternate access hole in

the bottom of appliance (see Figure 19,

page 13).

4. Repack insulation around gas line to cover

any remaining openings in conduit sleeve.

Prepare incoming gas line with teflon

tape or pipe joint compound and hook up

incoming gas line to exible gas line.

Note: If 1/2" NPT black iron pipe does not

mate with tting at the end of exible gas

line, remove tting and replace with a 37

degree are 3/4"-12, 1/2" NPT (female)

tting.

 WARNING: When nishing

appliance,donotoverlapcom-

bustiblematerialontotheblack

front face. Brick, tile or other

noncombustiblematerialsmay

beappliedtothefaceprovided

that any gap is between the

material used and the face is

caulkedwithanoncombustible

caulking.

Figure 7 - Rough Opening for Installing

in Wall

Figure 8 - Corner Installation Guidelines

These Dimensions Allow for a 3/4"

Clearance at Sides and Back of Fireplace.

However, 0" Clearance is Permitted

3/4" Clearance Not Required

at Nailing Flanges

M36E(B,H),

M36EP(B,H)

VM36E(B,H),

VM36EP(B,H)

M42E(B,H),

M42EP(B,H)

VM42E(B,H),

VM42EP(B,H)

A 40 3/8" (102 cm) 44 3/8" (112 cm)

B21 3/8" (54.3 cm) 23 1/8" (58.7 cm)

C 41 1/4" (104.8 cm) 48 1/4" (122.6 cm)

M36E(B,H),

M36EP(B,H)

VM36E(B,H),

VM36EP(B,H)

M4E2(B,H),

M42EP(B,H)

VM42E(B,H),

VM42EP(B,H)

A 24 1/2" (62.2 cm) 27 9/16" (70 cm)

B73 7/8" (187.6 cm) 83 7/8" (213 cm)

C 52 3/16" (132.6 cm) 59 5/16" (150.6 cm)

D 17 1/4" (43.8 cm) 19 1/2" (49.5 cm)

www.desatech.com

108796-01T 9

INSTALLING TRANSITION PIPE AND

STARTER COLLAR

The transition pipe and starter collar shown

in Figure 9 are supplied with replace, unat-

tached and ready for installation. Remove

starter collar and set aside. Slide transition

pipe over vent collar and attach with a mini-

mum of three screws. Replace starter collar

over transition pipe and attach using four

screws located on leg stands (ve used on

model M42E). To install B-vent piping, slide

rst piece of B-vent over transition pipe and

attach with either a minimum of two screws

or other means approved by the vent manu-

facturer. Figure 9 - Installing Transition Pipe and

Starter Collar

B-Vent Piping

Transition Pipe

Starter Collar

Vent Collar

PREINSTALLATION PREPARATION

Continued

VENTING INSTALLATION

at 60° or greater. The total vertical height in

this example represents the minimum height

of 8 feet and therefore the allowable lateral

is 6 feet when the 75% rule applies. If the

lateral length must exceed 75% then the

system must be sized in accordance with the

Category I venting tables.

Example2: Shows a multiple offset each at

45° of inclination. Multiple offsets are permit-

ted if they do not exceed 45° of inclination. The

total lengths of the two offsets are not required

to meet the 75% allowable rule.

Example3: Shows a single offset at 45° of

inclination and therefore the lateral length at

10 feet of offset does not have to meet the

75% rule.

In each case the offsets must be supported

and restops must be positioned wherever

the vent must pass through a sub-oor, ceil-

ing joist or an attic overhang. The vent pipe

must terminate vertically into a listed type vent

cap and extend a sufcient height through

an approved roof ashing, roof jack or a roof

thimble. At all points the listed clearances

must be maintained.

Vent terminations must be located in ac-

cordance with height and proximity rules of

NFPA No. 54. These rules apply to vents at

12" diameter or less and require a minimum

height in accordance with the roof pitch and a

minimum of 8 ft. distance from a vertical wall

or obstruction (see Figure 11, page 10).

A B-type venting system must be connected

to appliance for venting to the outside of

building.

The following section is provided as a guide

to a standard B-type vent installation.

Standing codes requirements concerning B-

type vent installations may vary within your

state, province or local codes jurisdiction.

Therefore, it is recommended that you check

with your local building codes for specic

requirements or in absence of local codes,

follow Section 7.0 of the current National Fuel

Gas Code ANSI Z223.1/NFPA 54.

This gas appliance must be vented to the

outdoors only and may not be terminated into

an attic space or into a chimney ue servicing

a solid-fuel burning appliance.

This appliance may be vented through a

manufactured chimney system or a masonry

chimney using a B-vent adapter or a chim-

ney liner system if all are listed, inspected

and approved by local codes and/or building

authorities.

The examples shown in Figure 10, page 10

are typical of most B-vent installations and

codes practices.

Example1: Shows the minimum allowable

system height and lateral offset for a 60° or

greater inclination. Code species that offsets

at 60° or greater are considered horizontal

and must follow the 75% rule for lateral to

total vertical system height. Codes also al-

low only one offset in the total system when

www.desatech.com 108796-01T10

Maintain

Listed

Clearance

Maintain

Listed

Clearance

12' Min.

12' Min. 45°

45°

12' Min.

60° 45°

Position

Firestop

Position

Firestop

Position

Firestop

Listed

Vent Cap

Listed

Vent Cap

Listed

Vent Cap

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Support Each

Lateral At

Least Every

6 Feet

Maintain

Listed

Clearance

10'

EXAMPLE 3EXAMPLE 2

EXAMPLE 1

Figure 10 - Typical B-Vent Conguration

VENTING INSTALLATION

Continued

If venting horizontally through a side wall be-

comes necessary, a listed thimble approved

for use with B-type vent must be used. Check

with your local codes before venting through

a side wall.

Some codes areas allow the use of existing

B-type vent systems if the system is at or

above the recommended diameter of the ue,

in this case 6".

The ue connection must be made using

listed B-type connectors and the existing

system must be code inspected for damage

and proper installation.

It is not recommended that this appliance be

common vented with an existing gas burning

appliance. However, if it becomes necessary

to common vent this appliance, the venting

system must be sized and congured in ac-

cordance with the common venting guides

Appendix G of the current National Fuel Gas

Code ANSI Z223.1/NFPA 54.

Note: Before connecting this appliance to an

existing vent system or a common venting

system consult with your local architect, plan-

ner or building ofcial.

WARNING: This appliance

must be properly connected

to a system and must not be

connected to a chimney ue

servicing a separate solid fuel

burningappliance.

Lowest

Discharge

Opening

Listed

Ve nt Cap

8 Ft. Min.

Roof Pitch x/12

Listed Clearance

Listed

Gas

Ve nt

H (Min)

Height

From Roof

Figure 11 - B-Vent Terminations

Roof Pitch

H(Min.)

Feet Meter

Flat to 6/12 1.0 0.30

6/12 to 7/12 1.25 0.38

Over 7/12 to 8/12 1.5 0.46

Over 8/12 to 9/12 2.0 0.61

Over 9/12 to 10/12 2.5 0.76

Over 10/12 to 11/12 3.25 0.99

Over 11/12 to 12/12 4.0 1.22

Over 12/12 to 14/12 5.0 1.52

Over 14/12 to 16/12 6.0 1.83

Over 16/12 to 18/12 7.0 2.13

Over 18/12 to 20/12 7.5 2.27

Over 20/12 to 21/12 8.0 2.44

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa Vanguard VVMR18 Quick start guide

Desa

Desa P324E Quick start guide

Desa

Desa CGEF26A Original instructions

Desa

Desa (V)G36HR Safety guide

Desa

Desa Vanguard VMH10TP Quick start guide

Desa

Desa VM42P Quick start guide

Desa

Desa (V)CB36P(E) User manual

Desa

Desa (V)368ST Quick start guide

Desa

Desa G8001 SERIES User manual

Desa

Desa MSVFBNR Series Quick start guide

Desa

Desa Vm42eP Quick start guide

Desa

Desa V36N SERIES Quick start guide

Desa

Desa Comfort Glow CHDV37N Quick start guide

Desa

Desa Wall Mantel and Base with Trim W32DS Instruction manual

Desa

Desa (V)T32EN-A Series, (V)T32EP-A Quick start guide

Desa

Desa Vanguard VCGF30NR Quick start guide

Desa

Desa ICBO# 3507 Quick start guide

Desa

Desa VK36EN Series Quick start guide

Desa

Desa CGCFTP Quick start guide

Desa

Desa CGEF26B Original instructions

Desa

Desa VTGF33PRB Quick start guide

Desa

Desa CGEF26 Original instructions

Desa

Desa CGEFP33PRB Quick start guide

Desa

Desa Vanguard VVSR18 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions