Delta TP04P User manual

- 1 -

………………………………………………………………… ENGLISH …………………………………………………………………

Thank you for choosing Delta TP series products. TP04P is a text panel PLC supporting

16~32 inputs and outputs, various instructions, and 8k steps SRAM for programming.

TP04P features the same program download port shared by both PLC and TP editing

software: WPLSoft and TPEditor. It also offers various graphical objects for developing

the program. The user can also obtain higher efficiency by purchasing additional

extension cards, which increase the program portability and save the program download

time. Please ensure to use TP series with Delta power supply module, DVPPS01 and

DVPPS02.

aPlease read this instruction carefully before use. This instruction sheet only provides

introductory information on electrical specifications, general specifications,

installation and wiring. For detailed information on programming and instructions,

please refer to “DVP-ES2/EX2/SS2/SA2/SX2/SE Operation Manual—Programming”.

For information about optional peripherals, please see individual product instruction

sheet enclosed with TP04P.

aSwitch off the power before wiring. DO NOT touch any terminal when the power is

switched on. DO NOT touch any internal circuit in 1 minute after the power is

switched off.

aDO NOT connect AC input power to any of the input/output terminals, otherwise

serious damage may occur. Check all the wiring again before switching on the

power.

aMake sure the ground terminal is correctly grounded in order to prevent

electromagnetic interference.

aThe display panels of TP04P series products are waterproof. However, please

prevent grease, corrosive liquids and sharp objects from contacting TP04P series

products.

aPlease use the fixed supports which are packed in the product package. Tighten the

cables or screws according to the specified torque, otherwise serious damage may

occur.

Product Outline and Dimensions

yFront Panel

P ow er ind ic ator

Alarm indicator

Display area

Escape/Exit key

Function/Nemeric keys

Up/Dow n ke ys

Enter key

Le ft/R ight keys

User-defined key

yBack Panel

Program copy

card interface

DC power suppl y

Program uplaod/download

communication port (USB)

RS485 communication

Run/Stop swtich

Input/output terminal blocks

Input/output

terminal blocks

- 2 -

yFront View and Right Side View (Units: mm, [ ]: inch)

91.73

[3.613]

59.2

[2.331]

175.8 [6.921]

108.6[4.276]

Figure1

yMounting Dimensions (Units: mm, [ ]:

inch)

yTop View (Units: mm, [ ]: inch)

Figure2

162.7~164.0 [6.4055~6.4567]

Thickness Range 0.5~5mm

95.5~97.0

[]

3.7598~3.8188

162.2

[6.386]

51.2

[2.016]

Figure3

Model Name and Serial Number

Series name

PLCmode

32TP04

P 1

Number of input/output points

Input/output function

Ou tpu t type

Function Specifications

Model

Spec. TP04P series

Screen type/Display

color STN-LCD/Monochromatic

Driver Delta automation products

Function/Numeric

keys 0~9, ESC, F, Enter and Up/Down/Left/Right keys

Alarm LED indicator

(Red)

Power indication (Blinking for three times)/Communication error

alarm/User program indication

Backlight

Automatically turning off the backlight: 1~99 minutes (0: The backlight

is not turned off.)

(The life span of the backlight is about 50,000 hours at a temperature

of 25°C)

Contrast adjustment Set by software, 10 levels of adjustment

Language/Font

ASCII: (Code page 850) Alphanumeric code (including European

characters)

Taiwan: Traditional Chinese fonts

China: Simplified Chinese fonts

Resolution 192 × 64 dots

Display range 101.8 mm (W) × 35.24 mm (H); 4.1” (diagonal)

Font size ASCII: 5 × 8, 8 × 8, 8 × 12, 8 × 16

- 3 -

Model

Spec. TP04P series

Display text 5×8 dots: 38 characters × 8 rows

8×8 dots: 24 characters × 8 rows

8×12 dots: 24 characters × 5 rows

8×16 dots: 24 characters × 4 rows

Program

upload/download

communication port

USB (COM1)

Transmission method: Virtual communication port

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits, Parity: None/Odd/Even

Baud rate: 9,600 bps~115,200 bps

USB: USB (Type B) terminal

Extension

communication port

RS485 (COM2)

RS485 (COM3)

Asynchronous transmission method: RS-485

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits, Parity: None/Odd/Even

Baud rate: 9,600 bps~115,200 bps

RS-485: 8 PIN-removable terminal block

Battery cover DC 3V battery

Monitoring method Download program to TP through virtual COM port

Extension interface Slot for a program copy card

Panel component Explanation

Alarm LED indicator

(Red)

Status 1: When power is ON, LED will start to blink slowly

Status 2: When the user-defined conditions are met, LED will blink for

one second repeatedly along with an alarm sound.

Power LED indicator

(Green) When the power is connected to the product, LED will be ON.

Display area LCM display area. It is used to display current program status.

Numeric keys 0~9: They function as constants. Users can also define the keys by

themselves.

Function keys Users can define the keys by themselves

Enter key If the input value is correct, users can press the key. Users can define

the key in the user page.

Up/Down/Left/Right

keys

Up: increase the value or move up one page.

Down: decrease the value or move down one page.

Left: Left direction key. Can be used to select the position of the

value.

Right: Right direction key. Can be used to select the position of the

value.

Electrical Specifications

Model

Spec. TP04P-16TP1R TP04P-32TP1R

CPU LPC1787FBD208

Program memory 1 MB-flash memory

RAM of the system 64K Bytes

Power supply voltage 24VDC (-15% ~ 20%) (With counter-connection protection on the

polarity of DC input power)

Power consumption 3.2W 5.2W

Power protection With counter-connection protection on the polarity of DC input

power

Insulation resistance > 5 MΩ(all I/O point-to-ground insulation resistance: 500 VDC)

Noise immunity

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O:

1KV,

Analog & Communication I/O: 1KV

Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

RS (IEC 61131-2, IEC 61000-4-3): 26MHz~1GHz, 10V/m

Ground

The diameter of ground cannot be less than the diameter of the

power cable. (If severla PLCs are used, they should be grounded

directly.)

Operating temperature

for hardware 0°C~50°C: Relative humidity: 20%-90% RH (non-condensing)

- 4 -

Model

Spec. TP04P-16TP1R TP04P-32TP1R

Storage temperature for

hardware -20°C~60°C

Waterproof class of the

front panel IP66/NEMA4

Vibration/Shock

resistance

International standards IEC61131-2, IEC 68-2-6 (TEST Fc)/

IEC61131-2 & IEC 68-2-27 (TEST Ea)

Weight 420g 444g

Dimensions 175.8 × 108.6 × 59.2 mm (Width(W) × Height(H) × Deep(D))

Cooling method Natural air cooling

Input terminal

Model

Item 24VDC (-15% ~ 20%) single common terminal

Input number X0, X1 X2~X7, X10~X17

Input type DC (Sinking or soucing)

Input voltage (±10%) 24VDC, 5mA

Input impedance 4.7k ohm

Maximum frequency 10KHz 60Hz

OffOn > 16.5 VDC

Action level OnOff < 8 VDC

OffOn <20us

Response

time OnOff <50us 10ms

Output terminal

Model

Item Relay

Current specifications 2A/1 point (5A/COM)

Voltage specifications 250VAC, < 30VDC

Resistive 1.5A /1 point (5A/COM)

Inductive #1

Current

specifications

Bulb 20WDC/100WAC

Response time

OffOn Approximately 10 ms

#1: Life curves

Contact

Current(A)

0.5

0.1 0.2

0.3 0.7 12

200

300

500

100

1,000

2,000

3,000

Operation(X10)

120VAC Resistive

30VDC Inductive(t=7ms)

240VAC Inductive(cos 0.4)

120VAC Inductive(cos =0.4)

30VDC

Inductive

(t=40ms)

Figure 4

I/O Configuration

- 5 -

Input Output I/O Configuration

Model

Point Type Point Type 32TP1R 16TP1R

TP04P-32TP1R 16 16

TP04P-16TP1R 8

(Sink or Source)

Relay

Y10

Y11

Y12

Y13

Y14

Y15

S/S0

Y16

Y17

S/S1

X10

X11

X12

X15

X16

X17

X14

X13

S/S0

Installation

Insert TP04P into the opening hole on the panel, and then tighten the screws. If it needs to be

mounted firmly, please use the mounting fixed supports and screws in the accessory package

which is packed with TP04P. Insert the hooks of the fixed supports into the fixing holes on the

back, and then tighten the screws. Please refer to figure 5 and figure 6 below for more

information.

(The torque exerted on a screw should be 4.75 (kg-cm). Please tighten the screws

according to the specifications, otherwise the product may be damaged. If the fixed supports

are not installed well, Delta will not guarantee the waterproof rating.) The cover of the mounting

panel should be waterproof/dust proof or meet the related specifications (IP66/NEMA4).

Do not install TP04P in the following environment.

hA location full of Airborne dust, metallic particles, oily smoke, corrosive or flammable

gases and liquids

hHigh-temperature and humid environment

hA location in which the product may be shocked and vibrated directly

Figure5

Figure6

Wiring

1. Please use single-core cables or twin-core cables. The

diameters of the cables used should be within the range

between 16 AWG and 22 AWG (1.5mm). The torque applied

to the screw terminals should be 1.90 kg-cm (1.65 in-lbs).

Please use copper conducting wires. The temperature of the

copper conducting wires should be 60/75°C.

22-16AWG

< 1.5mm

2. DO NOT wire the empty terminal. DO NOT put the input signal cables and the output signal

cables in the same wiring.

3. DO NOT drop any tiny metallic conductor into the PLC while you are tightening screw and

wiring the PLC. After the wiring is complete, you have to ensure that heat can radiate from the

PLC.

Power Supply

The power input of TP04P is DC. When you operates TP04P, please note the following

points:

1. The power is connected to two terminals, 24 VDC and 0 V, and the range of power is

20.4 to 28.8 VDC. If the power voltage is less than 20.4VDC, TP04P will stop running,

all outputs will be Off, and the ERROR indicator will start to blink.

2. If a power failure lasts for less than 10 ms, the operation of TP04P will not stop.

- 6 -

However, if a power failure lasts for long, or the power voltage decreases, TP04P will

stop running, and all outputs will be off. After the power returns to the normal status,

TP04P will automatically resume the operation. (Users have to note that TP04P is

equipped with latched auxiliary relays and registers when they write a program.)

Safety Wiring

Since TP04P is only compatible with DC power supply, Delta’s power supply modules

(DVPPS01/DVPPS02) are suitable for it. İt is suggested that you shoudl install a

protection circuit at the power supply terminal to protect DVPPS01 or DVPPS02. See

the figure below.

Figure 7

cAC power supply:100 ~ 240VAC, 50/60Hz dBreaker

eEmergency stop: The emergency stop button can be used to cut off the power when an

emergency occurs.

fPower indicator gAC power supply load

hPower supply circuit protection fuse (2A) iDVPPS01/DVPPS02

jDC power supply output: 24VDC, 500mA kDVP series PLC (main processing unit)

lDigital I/O module

Input Point Wiring

There are 2 types of DC inputs, SINK and SOURCE. (See the figures below)

zSINK Mode zSOURCE Mode

+2 4V 0V

DC Power Supply

S/S X0 X1 X2

Sink mode

Figure 8

Figure 9

+24V 0V

DC Power Supply

S/S X0 X1 X2

Source mode

Relay (R) output circuit wiring (Sink)

Figure 10

- 7 -

VDC

PLC Rela

output Smaller p ower

D: 1N4001 diode or equi valent com ponent

F i gur e1 1

ZDD

VDC

La rger power and

frequent on/off

ZD: 9V Z ener, 5W F igur e 12

PLC Rela

output

D: 1N4001 diode or equi valent com ponen t

PLC Rela

output AC loa d

R: 100~ 120

C: 0.1~0.24uF

Figure13

○

1DC power supply ○

2Emergency stop: An external switch is

used.

○

3Fuse: To protect the output circuit, a fuse having a breaking capacity within the range

between 5 A and 10 A is connected to the common terminal.

○

4Transient voltage suppressor: It increases the life span of the terminal.

1. Diode suppression of the DC load: It will be used if the power is small. (See figure 11.)

2. Diode + Zener suppression of the DC load: It is used when the power is large, and

TP04P is turned on and off frequently. (See figure 12.)

○

5Incandescent light (resistive load) ○

6AC power supply

○

7Mutually exclusive output: Y4 controls the clockwise rotation of the motor, and Y5

controls the counterclockwise rotation of the motor. The interlock circuit which is formed,

and the program in the PLC ensure that there are protective measures if an abnormal

condition occurs.

○

8Incandescent bulb: Neon light

○

9Absorber: It reduces the interference from the AC load. (See figure 13)

RS-485 Wiring

Figure 14

D+ D- D+ D- D+ D-

1 2 2

cMaster station dSlave station eTerminal resistor

Note: 1. The terminal resistor should be connected to the master station and the last slave

station. The resistance of the terminal resistor should be 120Ω.

2. To ensure communication quality, it is suggested that users should use double shielded

twisted pair cables (20AWG) for wiring.

Communication Connection

TP04P may connect to a PC by using USB adaptor cable.

Please use an AM/BM USB adaptor cable.

Figure15

Battery’s Life

Temperature (°C) -20 0 20 60

Life (Year) 2.0 2.5 2.7 2.8

Precision of the Real Time Clock

(Second/Month)

Temperature (°C/°F) 0/32 25/77 55/131

Maximum error (Second) -117 52 -132

- 8 -

………………………………………………………………繁體中文 …………………………………………………………………………

感謝您採用台達文本顯示器系列產品。TP04P 結合 PLC 與文本顯示器一體，為 16~32 點

PLC 主機，具有豐富的指令集及 8k steps 的程式記憶體。TP04P 分別支援 PLC 與TP 編

輯軟體，可共用同一個下載埠；TP 軟體規劃部份提供多種物件圖形供使用者選用。使用

者可另購程式擴充卡，快速移植程式，節省程式下載時間。請搭配台達 DVPPS01 及

DVPPS02(電源模組)一起使用。

a請在使用之前，詳細閱讀本使用說明書。本安裝說明書提供給使用者電氣規格、功能

規格、安裝配線之相關注意事項。其他詳細之程式設計及指令說明請見

DVP-ES2/EX2/SS2/SA2/SX2/SE 操作手冊【程式篇】，選購之周邊裝置詳細說明請見

該產品隨機安裝說明書。

a於實施配線前，請務必關閉電源。請勿在上電時觸摸任何端子。輸入電源切斷後，一

分鐘之內，請勿觸摸內部電路。請勿在上電時觸摸任何端子。

a交流輸入電源不可連接於輸入⁄出信號端，否則可能造成嚴重損壞，請在上電之前再次

確認電源配線。

a本體上之接地端子務必正確的接地，可提高產品抗雜訊能力。

a本機顯示操作面板防水，但對油污或具腐蝕性之液體不具防護作用，避免以尖銳之物

品刮傷面板使用時請注意。

a利用原廠包裝附件之固定架，鎖緊面板固定螺絲時，請勿太緊以免造成機殼損壞。

產品外觀尺寸與部位介紹

y正面圖

電源指示燈

警示指示燈

顯示區

數字功能鍵

退出取消鍵/

上下鍵

輸入鍵

左右鍵/

使用者定義

y背面圖

USB程序

下載埠上

直流電源供應

RS485通訊

Run/Stop開關

輸入輸出點

部端子外

程序複製卡

面介

輸入輸出

點

部端子外

y正面圖及右側圖（單位：公厘，[ ]：英吋）

詳細尺寸圖請參閱英文版之Figure1。

- 9 -

y嵌入開孔尺寸（單位：公厘，[ ]：英吋）

詳細尺寸圖請參閱英文版之Figure2。

y俯視圖（單位：公厘，[ ]：英吋）

詳細尺寸圖請參閱英文版之Figure3。

產品名稱與編碼

系列名稱

PLC模式

輸入輸出點數/

32TP0

輸入點輸出功能/

輸出點型態

功能規格

機型

規格 TP04P 系列

螢幕/色彩 STN-LCD / 單色

驅動器台達產品

功能鍵／數字鍵 0 ~ 9，ESC，F，Enter及上／下／左／右鍵

警示指示燈（紅燈）電源啟動指示（亮／滅三次）／通訊不通警示／使用者程式指定

背光型式背光自動關閉設定範圍1 ~ 99分鐘（設定值0為不關閉）

（在常溫25℃下壽命約5萬小時）

對比調整軟體設定，10段明暗調整

語言字型 ASCII：（頁碼850）文字（包含歐洲字型）、繁體字型及簡體字型

解析度 192 × 64 點

顯示範圍（寬）×（高）= 101.8 × 35.24（單位：公厘）；4.1吋（對角線）

字型大小 ASCII：5 × 8，8 × 8，8 × 12，8 × 16

顯示的文字數 5×8 畫素字型：38 個字 × 8 列

8×8 畫素字型：24 個字 × 8 列

8×12 畫素字型：24 個字 × 5 列

8×16 畫素字型：24 個字 × 4 列

程式上下載通訊埠

USB（COM1）

傳送方式：虛擬通訊埠

資料長度：7或8 bits，停止位元：1或2 bits，極性：無／奇／偶

傳送速度：9,600bps ~ 115,200bps

USB：USB (Type B) 端子

擴充通訊埠

RS485 (COM2)

RS485 (COM3)

非同步傳送方式：RS-485

資料長度：7或8 bits，停止位元：1或2 bits，極性：無／奇／偶

傳送速度：9,600bps ~ 115,200bps

RS-485：8 PIN 脫落式端子

電池蓋可由此更換直流3V電池

監控方式通過虛擬通訊埠下載至TP

擴充介面程式複製卡插槽

面板元件說明

警示指示燈（紅燈）

狀態一：當啟動電源時，指示燈慢慢開始閃爍。

狀態二：當符合使用者設定條件時，指示燈會重覆持續亮一秒並發出警

報聲。

Other manuals for TP04P

This manual suits for next models

Table of contents

Other Delta Plumbing Product manuals

Delta

Delta ZURA 77418 User manual

Delta

Delta Cassidy 2597LF-MPU Series User manual

Delta

Delta 41618 User manual

Delta

Delta Classic 502-DST Series User manual

Delta

Delta MultiChoice R10000 Series User manual

Delta

Delta 467-DST Series User manual

Delta

Delta 2523 Series User manual

Delta

Delta 4555 Series User manual

Delta

Delta T2730 Series User manual

Delta

Delta 25702LF Series User manual

Delta

Delta 100 Series User manual

Delta

Delta 590T1 0-HP Series User manual

Delta

Delta GANOT 95A9135-33S-SS User manual

Delta

Delta Dryden 4551 Series User manual

Delta

Delta 142939-I Series User manual

Delta

Delta 3538 Series User manual

Delta

Delta ITS61350 User manual

Delta

Delta T27T859 User manual

Delta

Delta JETTED SHOWER XO R1817 User manual

Delta

Delta 5SE-SBS-6 Series User manual

Delta

Delta 597LF MPU Series User manual

Delta

Delta 753LF Series User manual

Delta

Delta 55446-CN User manual

Delta

Delta T2769 User manual

Popular Plumbing Product manuals by other brands

Weka

Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS

Kohler

Kohler K-6228 Installation and care guide

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Operator's manual

American Standard

American Standard DetectLink 6072121 manual

Uponor

Uponor Contec TS Mounting instructions

Pfister

Pfister Selia 49-SL Quick installation guide

Fortis

Fortis VITRINA 6068700 quick start guide

Fortis

Fortis MILANO 78211JS installation instructions

Kohler

Kohler K-12183 Homeowner's guide

Maxxus

Maxxus MX-M206-01 instruction manual

Moen

Moen 5922 Series installation instructions

Viega

Viega Prevista Pure 8512 Instructions for use

Kohler

Kohler Centerset K-15240 Homeowner's guide

Viega

Viega Prevista Dry 8522.33 Instructions for use

Sanela

Sanela Lema SLP 59RB Instructions for use

Elkay

Elkay EDF15AC Installation, care & use manual

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions

baliv

baliv WT-140 manual