Dell PowerEdge 1750 User manual

Other manuals for PowerEdge 1750

7

Table of contents

Other Dell Server manuals

Dell

Dell PowerEdge R230 User manual

Dell

Dell PowerEdge SC420 Parts list manual

Dell

Dell PowerEdge R510 User manual

Dell

Dell PowerEdge 1655MC Technical manual

Dell

Dell POWEREDGE CLUSTER SE100 Assembly Instructions

Dell

Dell External OEMR R210II User manual

Dell

Dell PowerEdge 2420 User manual

Dell

Dell Force10 MXL Blade User manual

Dell

Dell PowerEdge 1750 Manual

Dell

Dell PowerEdge R730 User manual

Dell

Dell PowerEdge 1955 User manual

Dell

Dell PowerEdge 4350 User manual

Dell

Dell 3250 Technical manual

Dell

Dell PowerEdge 2650 User manual

Dell

Dell Wyse 3030 LT User manual

Dell

Dell EMC PowerEdge MX740c User manual

Dell

Dell PowerEdge 2650 User manual

Dell

Dell PowerEdge T100 User manual

Dell

Dell POWEREDGE 1900 Technical manual

Dell

Dell PowerEdge T620 Manual

Dell

Dell PowerEdge R760 Manual

Dell

Dell Force10 S2410-01-10GE-24P Installation manual

Dell

Dell PowerEdge 500SC Technical manual

Dell

Dell DSS 1510 User manual

Popular Server manuals by other brands

HP

HP AlphaServer ES47 Cli reference manual

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

EtroVISION

EtroVISION EV3151 user manual

NEC

NEC Express5800/T110j System configuration guide

HP

HP ProLiant Gen9 user guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

HP

HP Integrity rx2600 overview

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual

Lenovo

Lenovo ThinkSystem SR635 V3 user guide

Fujitsu

Fujitsu PRIMERGY BX900 quick start guide

Asus

Asus RS700DA-E6 PS4 user manual

Dell Poweredge 1750

Installing a ROMB Card (PERC4/DI)

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, see "Safety First—For

You and Your System" in "Troubleshooting Your System."

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTICE: To avoid possible data loss, back up all data on the hard drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1. Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your

System."

3. Locate the ROMB card connector on the system board. See Figure A-3.

4. If a PCI card is installed over the ROMB card connector, remove it. See "Removing an

Expansion Card."

5. Position the ROMB card with the notch in its plastic cover facing the redundant power

supply bay, and align the edges of the card with the four plastic standoffs on the

system board.

6. Press down on the three "bulls eyes" on the ROMB card cover until the four plastic

standoffs snap over the edge of the card. See Figure 6-11.

Figure 6-11. Installing the ROMB Card and Backup Battery

7. Install the ROMB backup battery:

a. Position the battery board as shown in Figure 6-11, and press it down into the

two standoffs until it snaps into place.

b. Plug the battery cable into the RAID BATTERY connector on the system board.

8. If you removed a PCI card in step 4, replace it. See "Installing an Expansion Card."

9. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your

System."

10. Reconnect the system and peripherals to their power sources, and turn them on.

11. Enter the System Setup program and verify that the setting for the SCSI controller has

changed to reflect the presence of the RAID hardware. See "Using the System Setup

Program" in your User's Guide.

12. Install the RAID software. See the ROMB card software documentation for more

information.

Removing a ROMB Card

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, see "Safety First—For

You and Your System" in "Troubleshooting Your System."

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTICE: To avoid possible data loss, back up all data on the hard drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1. Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your

System."

3. If a PCI card is installed over the ROMB card, remove the PCI card. See "Removing an

Expansion Card."

4. Pull the ROMB card up out of the four standoffs. See Figure 6-11.

5. Disconnect the ROMB backup battery from the backup battery connector, and pull the

battery assembly up out of the two standoffs. See Figure 6-11.

6. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your

System."