Dascom DC-7600 User manual

Assembling the Hardware to make the DC-7600 Lamination Station

After receiving the DC-7600 Lamination station, some assembly is required. his Instructions set will help in

providing the steps to assembly the station quickly.

You will need a

1) Magnetic #1 Phillips screwdriver to assembly the hardware that makes up the station.

First, take inventory of the parts you received.

Laminator Stand

DC-5100

Laminator

Laminator Power

Brick assembly

USB

Cable

Laminator to Printer

Communication Cable

DC-7600

Card Printer

Station

Mounting Plate

Laminator Fastening

Hardware and

Laminate RFID Tag

Laminate and

Take-up Spool DC-7600 Card Printer Assesories

Printer

Fastening

Hardware

0.76mm

PVC Cards

Step 1 – Fasten the Mounting Plate to the DC-7600 Card Printer

1) Place the (6) fastening screws into the

rubber feet.

2) Lower the printer GE TLY onto its back

and position the Mounting Plate over the

bottom of the Printer(flat edge of plate to

rear of the Printer), aligning the Mounting

Plate holes with the mounting holes on

the bottom of the Printer.

3) Insert the Rubber Feet screws through the

Mounting Plate holes and fasten the Plate

onto the bottom of the Printer.

4) Fasten the two remaining Rubber feet to the

bottom side of the Plate, opposite of the Printer

side.

5) Once all (6) Rubber Feet are fastened to the Plate,

carefully lift the Printer and Mounting Plate upright.

Step 2 – attach the Laminator Station Stand to the Mounting Plate.

2) Place and align the Laminator Stand alignment 3) Using a magnetic #1 Phillips Screw driver and the

posts, as noted, to the Mounting Plate. 4 supplied screws.

4) Fasten the Stand to the Mounting Plate 5) Stand fastened securely to Mounting Plate

in all four locations, securing it to the Plate.

Step 3 – Prep the Stand for the Laminator

Place the Power Adapter into the Laminators Stand, as seen above, with the power receptacle facing outwards

and the power plug for the laminator extending out of the stand.

Step 4 – Placing the Laminator onto its Stand

Gently lower the DC-5100 Laminator onto the stand, making sure to align it to the Stand.

Read the “Connections” instructions for properly wiring the Laminator to the Printer.

Connection Instructions for the DC-7600 Laminator Station

Hardware Connections :

Note: Before connecting the laminator and the DC-7600 power supplies, first make sure that the laminator

and the DC-7600's power utton are in the Off state.

After connecting the power supply, turn on the laminator power supply first and then turn on the DC-7600

power supply.

The RFID Tag Slot

for identifying the

Laminate.

USB Port connection

from the PC

Serial Cable – Connection between

the Laminator and the DC-7600 Printer

Laminator Power Supply

Laminator Base

Bottom Plate – The

DC_7600 and Laminator

are fixed to the bottom

plate.

Other manuals for DC-7600

1

Other Dascom Printer manuals

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide