Da-Lite IMAGER User manual
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: [email protected]
POWER
PRESENTATION PRODUCTS
The
In
Instruction Book for
IMAGER
1
LARGE WALL BRACKET (47" LONG)
Quantities vary by screen size:
Screens 80" and smaller viewing width = 1
Screens over 80" to 96" viewing width = 2 QUANTITY INCLUDED __________
Screens over 96" viewing width = 3
Installation screws not included
SMALL WALL BRACKET (8" LONG)
Quantity = 1. Only for screens
80" and smaller viewing width.
QUANTITY INCLUDED __________
Installation screws not included
#10 SCREW
Quantity = 16
(8 attached to frame)
QUANTITY INCLUDED ________
CORNER BRACKET
Quantity = 4
(attached to frame)
QUANTITY INCLUDED ________________________________
INSTALLATION
There are three methods of installation based on the size of the screen. Measure the width of the viewing area of your
screen and refer to the appropriate method of installation below. The hanger bracket figure shows the type and quantity
of bracket that is supplied based on the size of the screen.
Method 1: Screens 80" and smaller in viewing width.
Method 2: Screens over 80" up to 96" in viewing width.
Method 3: Screens over 96" in viewing width.
USE INSTALLATION
METHOD NUMBER __________
SNAP STUD
QUANTITY INCLUDED ________
SETTING UP YOUR SCREEN
2
TOOLS REQUIRED: Phillips Screwdriver
Carpenter’s Level
Tape Measure
FRAME ASSEMBLY
1.
Place the four frame pieces on a clean floor.
2.
Slide the frame pieces together at corners. (Note: Frame assembly holes may not appear to fit properly at the corners
until all fasteners have been attached. Once fasteners are attached, the frame corners will be drawn in for a proper fit.)
Secure frame pieces with #10 screws provided. Do not tighten screws until all are started, then tighten. See Figure 1.
3.
Tighten the two screws at each corner. Do not over-tighten
the screws.
4. Insert and tighten the snap stud in the center of the corner
bracket (Figure 1).
ATTACH THE VIEWING SURFACE
Unroll the screen on a clean surface. Do not use newspaper.
The viewing side is rolled to the inside of the roll. Place the
frame over the screen surface, and while lifting the frame with
one hand, snap the screen surface onto the frame with the
other hand while maintaining a steady pull on the surface.
Method 1
1. Secure the large wall bracket to wall studs at the desired height. Make sure the bracket is level. The top of the frame
will be 1/8" above the top of the wall bracket when mounted. You will need at least 5/8" clearance above the bracket
to hang the screen. Figures 2, 3, and 4 show the proper orientation for the supplied wall brackets.
2. To install the small wall bracket, you must measure the overall height of the screen frame and subtract 1-3/8". Using
that dimension, measure down from the top edge of the wall bracket and mark the wall for two screw holes. The
holes should be centered within the frame and 6" apart. Refer to Figure 3.
3. Attach the small wall bracket to the wall. Refer to Figure 4 for proper orientation. Do not tighten the screws
completely. The bracket should slide up and down easily.
4. Hang the screen on the brackets by hooking the bottom of
the frame onto the small wall bracket and lift up until you
can hook the top of the frame on the top large bracket.
Push down on the frame to seat it on the brackets. Refer to
Figure 4.
METHOD 1 (SCREENS 80" AND SMALLER IN VIEWING WIDTH)
FIGURE 2 SMALL WALL BRACKET
1-PIECE
LARGE WALL
BRACKET
1-PIECE
FIGURE 1
3
Method 2
1. Secure the large wall bracket to wall studs at
the desired height. Make sure the large bracket
is level. The top of the frame will be 1/8" above
the top of the large wall bracket when
mounted. You will need at least 5/8" clearance
above the bracket to hang the screen. Figures 5
and 6 show the proper orientation for the
supplied wall brackets.
2. To install the lower wall bracket, you must
measure the overall height of the screen frame
and subtract 1/4". This is the dimension from
the top of the upper wall bracket to the bottom
of the lower wall bracket. See Figure 6.
3. Position the screen with the attached surface
onto the top wall bracket as shown in Figure 6.
Push down at the center of the bottom frame
rail to hook onto the lower wall bracket.
METHOD 1 (SCREENS 80" AND SMALLER IN
VIEWING WIDTH)
FIGURE 3
LARGE WALL
BRACKET
OVERALL HEIGHT - 1-3/8"
6"
OVERALL
HEIGHT
FIGURE 4
2
LIFT
1
3
WALL
FIGURE 5
LARGE WALL
BRACKET
2-PIECES
FIGURE 6
OVERALL
HEIGHT -1/4"
WALL
OVERALL
HEIGHT
2
1
METHOD 2 (SCREENS OVER 80" UP TO 96" IN
VIEWING WIDTH)
4
Da-Tex®, Dual Vision, Pearlescent, Cinema Vision,
Da-Mat®, High Contrast Da-Mat®, Audio Vision,
High Contrast Audio Vision, High Contrast Cinema Vision
and High Contrast Cinema Perf surfaces can be
cleaned as follows:
Using a white clean cloth (100% cotton preferred)
that is dampened with clear water, gently wipe the
area in one direction. Do not use a circular motion.
Using a dry 100% cotton cloth, wipe dry after each
cleaning session. To clean a stubborn stain or a
sticky surface, use denatured alcohol (methanol or
methyl alcohol) following the same procedure as for
water.
CLEANING
METHOD 3 (SCREENS OVER 96" IN VIEWING
WIDTH)
1. Secure the large wall brackets to wall studs at
the desired height. Make sure the brackets are
level. The top of the frame will be 1/8" above the
top of the large wall bracket when mounted.
You will need at least 5/8" clearance above the
bracket to hang the screen. Figures 6 and 7
show the proper orientation for the supplied
wall brackets.
2. To install the lower large wall bracket, you must
measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper large wall bracket to the
bottom of the lower large wall bracket. See
Figure 6.
3. Position the screen with the attached surface
onto the top large wall bracket as shown in
Figure 6. Push down at the center of the bottom
frame rail to hook onto the lower large wall
bracket.
FIGURE 7
LARGE WALL
BRACKETS
3-PIECES
Printed in U.S.A. 86478 Rev. 1/08
5
Table of contents
Other Da-Lite Projection Screen manuals
Da-Lite
Da-Lite Theater-lite User manual
Da-Lite
Da-Lite Designer Manual User manual
Da-Lite
Da-Lite Da-Snap Wrap Around Screen User manual
Da-Lite
Da-Lite Tensioned Contour Electrol 38798LC User manual
Da-Lite
Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual
Da-Lite
Da-Lite Designer Contour Manual User manual
Da-Lite
Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual
Da-Lite
Da-Lite Parallax Thin User manual
Da-Lite
Da-Lite Polacoat Da-Plex Semi-Rigid User manual
Da-Lite
Da-Lite PERM WALL FRAME User manual
Da-Lite
Da-Lite ADVANTAGE DELUXE ELECTROL User manual
Da-Lite
Da-Lite DESIGNER MANUAL SCREEN User manual
Da-Lite
Da-Lite Picture King User manual
Da-Lite
Da-Lite TENSIONED EXECUTIVE ELECTROL User manual
Da-Lite
Da-Lite DESIGNER CONTOUR ELECTROL Series User manual
Da-Lite
Da-Lite MULTI-MASK IMAGER User manual
Da-Lite
Da-Lite Horizon Electrol User manual
Da-Lite
Da-Lite Cosmopolitan Electrol User manual
Da-Lite
Da-Lite Viewshare tensioned Advantage Electrol User manual
Da-Lite
Da-Lite EXECUTIVE ELECTROL User manual
Popular Projection Screen manuals by other brands
FART PRODUKT
FART PRODUKT Standard SCREEN Installation instruction
Draper
Draper E Series Installation & operating instructions
Elite Screens
Elite Screens Elite Tripod Series user guide
Laarhoven
Laarhoven Companion II General assembly instructions
Renogy
Renogy RMS-LFPS-US manual
Samsung
Samsung S*H65* user manual
