Da-Lite Da-Snap 79982 User manual

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

www.da-lite.com

e-mail: [email protected]

POWER

PRESENTATION PRODUCTS

The

Instruction Book for

DA-SNAP SCREEN

1. Unpack the frame parts from the carton. DO NOT

unroll the screen surface at this time.

2. Slide the frame pieces together at corners. (Note:

Frame assembly holes may not appear to fit properly

at the corners until all fasteners have been attached.

Once fasteners are attached, the frame corners will

be drawn in for a proper fit.) Secure frame pieces

with #10 screws provided. Do not tighten screws

until all are started, then tighten. See Figure 1.

NOTE: The frame pieces are labeled “top” and “bottom”.

Be sure the frame pieces are assembled according to the

labels. This will ensure the snap pattern on the frame and

screen surface will match.

FRAME ASSEMBLY

FIGURE 1. REAR VIEW

SNAP STUD

SIDE

#10 BLACK SCREW

SIDE

TOP

BOTTOM

SNAP STUD

LARGE WALL BRACKET (47" LONG)

Quantities vary by screen size:

Screens smaller than 80" viewing width = 1

Screens 80" to 96" viewing width = 2 QUANTITY INCLUDED __________

Screens over 96" viewing width = 3

Installation screws not included

SMALL WALL BRACKET (8" LONG)

Quantity of 1. Only for screens

smaller than 80" viewing width QUANTITY INCLUDED __________

Installation screws not included

SNAP STUD

QUANTITY INCLUDED ________

#10 SCREW

QUANTITY INCLUDED ________

FRAME BRACKET

Quantities vary by screen size

Screens smaller than 80" viewing width = 3

Screens 80" to 96" viewing width = 4

Screens over 96" viewing width = 6

QUANTITY INCLUDED ________________________________

HIGH POWER FRAME BRACKET

Screens with High Power viewing surface quantity = 2

Screens with 2-piece side frame rails quantity = 2

Screens 10' to 16' viewing width = 2

QUANTITY INCLUDED ________________________________

USE INSTALLATION

METHOD NUMBER __________

There are four methods of installation based on the size

of the screen and type of viewing surface. Measure the

width of the viewing area of your screen and refer to the

appropriate method of installation below. The wall

bracket diagram shows the type and quantity of bracket

that is supplied based on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power viewing

surface.

INSTALLATION

4. Attach the small wall bracket to the wall. Refer to

Figure 4 for proper orientation. Do not tighten the

screws completely. The bracket should slide up and

down easily.

5. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the inside of

the roll. Place the frame over the screen surface, and

while lifting the frame with one hand, snap the

screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

6. Hang the screen on the brackets by hooking the

bottom of the frame onto the small wall bracket and

lift up until you can hook the top of the frame on the

top bracket. Push down on the frame to seat it on the

brackets. Refer to Figure 4.

OVERALL HEIGHT - 1-3/8"

OVERALL

HEIGHT

LIFT

WALL

1. Use the supplied #10 screws to attach three frame

brackets to the back of the frame as shown in Figure

2. Secure the large wall bracket to wall studs at the

desired height. Make sure the bracket is level. The

top of the frame will be 1/8" above the top of the wall

bracket when mounted. You will need at least 5/8"

clearance above the bracket to hang the screen.

3. To install the small wall bracket, you must measure

the overall height of the screen frame and subtract

1-3/8". Using that dimension, measure down from the

top edge of the large wall bracket and mark the wall

for two screw holes. The holes should be centered

within the frame and 6" apart. Refer to Figure 3.

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

FIGURE 2

FRAME BRACKETS

3-PIECES

#10 SCREWS

6-PIECES

LARGE WALL

BRACKET

1-PIECE

SMALL WALL BRACKET

1-PIECE

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

FIGURE 3

FIGURE 4

1. Use the supplied #10 screws to attach four frame

brackets to the back of the frame as shown in

Figure 5.

2. Secure the wall bracket to wall studs at the

desired height. Make sure the bracket is level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen.

3. To install the lower wall bracket, you must

measure the overall height of the screen frame

and subtract 1/4". This is the dimension from the

top of the upper wall bracket to the bottom of the

lower wall bracket. See Figure 6.

4. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

5. Position the screen with the attached surface

onto the top wall bracket as shown in Figure 7.

Push down at the center of the bottom frame rail

to hook onto the lower wall bracket.

FIGURE 5

FRAME BRACKETS

4-PIECES

#10 SCREWS

8-PIECES

LARGE WALL

BRACKET

2-PIECES

FIGURE 6

OVERALL HEIGHT -1/4"

OVERALL HEIGHT

WALL

FIGURE 7

METHOD 2 (SCREENS OVER 80" UP TO 96" IN VIEWING WIDTH)

1. Use the supplied #10 screws to attach six frame

brackets to the back of the frame as shown in

Figure 8.

2. Secure the wall brackets to wall studs at the

desired height. Make sure the brackets are level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen.

3. To install the lower wall bracket, you must

measure the overall height of the screen frame

and subtract 1/4". This is the dimension from the

top of the upper wall bracket to the bottom of the

lower wall bracket. See Figure 6.

4. For 150", 180", 200", 220" and larger screens with

2-piece side frame rails you will will need to

attach one High Power bracket to each side

frame rail. Use the black #10 screws supplied.

See Figure 8.

5. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

6. Position the screen with the attached surface

onto the top wall bracket as shown in Figure 7.

Push down at the center of the bottom frame rail

to hook onto the lower wall bracket.

7. If you attached brackets to the side frame rails in

step 4, anchor these to the wall with an

appropriate fastener for your type of wall.

1. Use the supplied #10 screws to attach two frame

brackets and two High Power brackets to the

back of the frame as shown in Figure 9.

2. Secure the large wall bracket to wall studs at the

desired height. Make sure the bracket is level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen.

3. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

4. Position the screen with the attached surface

onto the top wall bracket as shown in Figure 7.

Push down at the center of the bottom frame rail

to tension the fabric. Mark the screw holes for

the bottom brackets. Drill holes in wall and attach

the brackets to the wall with screws.

FIGURE 9

FRAME BRACKETS

2-PIECES

#10 SCREWS

8-PIECES

LARGE WALL

BRACKET

1-PIECE

HIGH POWER BRACKET

2-PIECES

METHOD 3 (SCREENS OVER 96" IN VIEWING

WIDTH) METHOD 4 (HIGH POWER FABRIC)

FIGURE 8

FRAME BRACKETS

6-PIECES

#10 SCREWS

12-PIECES

LARGE WALL

BRACKETS

3-PIECES

HIGH

POWER

BRACKET

FOR

LARGE

SPLIT

FRAMES,

AND 150",

180", 200"

AND 220"

DIAGONAL

SCREENS.

2-PIECES

Printed in U.S.A. 75135 Rev. 5/07

CLEANING

Da-Tex, Dual Vision, Pearlescent, Cinema Vision, High Power,

Da-Mat, High Contrast Da-Mat, Audio Vision, High Contrast

Audio Vision, High Contrast Cinema Vision and High Contrast

Cinema Perf surfaces can be cleaned as follows:

Using a white clean cloth (100% cotton preferred) that is

dampened with clear water, gently wipe the area in one

direction. Do not use a circular motion. Using a dry

100% cotton cloth, wipe dry after each cleaning

session. To clean a stubborn stain or a sticky surface,

use denatured alcohol (methanol or methyl alcohol)

following the same procedure as for water.

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite Deluxe Insta-theater User manual

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite HORIZON ELECTROL User manual

Da-Lite

Da-Lite DESIGNER MANUAL SCREEN User manual

Da-Lite

Da-Lite VERSATOL User manual

Da-Lite

Da-Lite Whiteboard Mount User manual

Da-Lite

Da-Lite Da-Glas User manual

Da-Lite

Da-Lite advantage User manual

Da-Lite

Da-Lite DUAL MASKING ELECTROL User manual

Da-Lite

Da-Lite SENIOR ELECTROL User manual

Da-Lite

Da-Lite senIor electrol User manual

Da-Lite

Da-Lite ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite Tensioned Conference Electrol User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Polacoat Da-Plex Semi-Rigid User manual

Da-Lite

Da-Lite Designer Contour® User manual

Da-Lite

Da-Lite ViewShare Advantage Electrol Retrofit User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite Senior Electrol User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Picture King User manual

Da-Lite

Da-Lite DESIGNER CONTOUR MANUAL User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions