ComAp InteliNano NT MRS User manual

ComAp,a.s.

Kundratka 2359/17

180 00, Praha 8

Czech Republic

InteliNano-NT MRS, SW version 1.5, ©ComAp –September 2013 1

InteliNano-NT-MRS-1.5-Fast User Guide.pdf

CAN INTERFACE

GENERATOR VOLTAGE

MEASUREMENT

T16 = Neutral

T17 = Phase 1

T18 = Phase 2

T19 = Phase 3

USB interface

COM

INTPUT TERMINALS

T10 = COM for analog inputs

T11 = binary input

T12 = binary input

T13 = binary/analog input –Low Fuel Level

T14 = binary/analog input –Coolan Temperature

T15 = binary/analog input –Oil Pressure

OUTPUT TERMINALS

T04 = binary output –Starter (6A)

T05 = binary output - Fuel Solenoid (6A)

T06 = binary output (500 mA)

T07 = binary input/output (500 mA)

POWER SUPPLY, D+

T01 = BATT -

T02 = D+

T03 = BATT +

ECU

DIESEL / GASOLINE ENGINE GENERATOR

LOAD

Fuel Solenoid

Battery

Sarter

Fuel Level Analog

Coolant Temperature Analog

Oil Pressure Analog

D+

Alarm

Ready To Load

Fuel Solenoid

Starter

COM

Remote Start And Load

Emergency Stop

CAN

L COM H

USB

Battery +

Battery -

D +

InteliNano NT



MRS Fast User Guide

Typical wiring diagram

Accessing the setup mode

Ensure the engine is stopped and the controller is in Manual mode (green LED above button Auto is turned off).

If you have not configured the custom initialization (init) screen then press and hold Stop button, then briefly press ▲button and then Auto .

If you have already created your own init screen then press and hold Stop button and then briefly press ▲, the custom init screen will appear, keep holding the Stop

button. Then press ▼to switch LCD to default init screen, and then press Auto.

To move up and down in the setup menu use ▲and ▼buttons. Press Start button to select or Stop button for exit.

Basic settings

Input settings

Engine parameters and protections

ECU setting

Generator protections

Info

Output settings

Outputs and inputs

Output

code

Output source

Type

Terminal assignment

O00

Not Used

binary

T04, T05, T06, T07

O01

Starter

binary

T04

O02

Fuel Solenoid

binary

T04, T05, T06, T07

O03

Stop Solenoid

binary

T04, T05, T06, T07

O04

Alarm

binary

T04, T05, T06, T07

O07

Ready To Load

binary

T04, T05, T06, T07

O08

Prestart

binary

T04, T05, T06, T07

O09

ECU Power Relay

binary

T04, T05, T06, T07

O10

Choke

binary

T04, T05, T06, T07

O11

Glow Plugs

binary

T04, T05, T06, T07

Normally Open Contact –output

Normally Open Contact - input

button

Normally Closed Contact –output

Normally Closed Contact –input

button

User curves

I21

I23

I25

VDO Level %

VDO 5 Bar

VDO 40-120 °C

Datcon Level %

VDO 10 Bar

VDO 50-150 °C

Datcon 5 Bar

Datcon High °C

Datcon 7 Bar

Datcon Low °C

Datcon 10 Bar

Not selected

Input

code

Input source

Type

Terminal assignment

I00

Not Used

binary

T07, T11, T12, T13, T14, T15

I01

Emergency Stop

binary

T07, T11, T12, T13, T14, T15

I02

Remote Start/Stop

binary

T11

I03

Remote Start And Load

binary

T11

I04

Access Lock

binary

T07, T11, T12, T13, T14, T15

I07

GCB Feedback

binary

T07, T11, T12, T13, T14, T15

I10

External Warning 1

binary

T07, T11, T12, T13, T14, T15

I11

External Warning 2

binary

T07, T11, T12, T13, T14, T15

I12

External Warning 3

binary

T07, T11, T12, T13, T14, T15

I13

External Shutdown 1

binary

T07, T11, T12, T13,T14, T15

I14

External Shutdown 2

binary

T07, T11, T12, T13, T14, T15

I15

External Shutdown 3

binary

T07, T11, T12, T13, T14, T15

I20

Low Fuel Level

binary

T07, T11, T12, T13, T14, T15

I21

Fuel Level Analog

analog

T13, T14, T15

I22

Low Oil Pressure

binary

T07, T11, T12, T13, T14, T15

I23

Oil Pressure Analog

analog

T13, T14, T15

I24

High Coolant Temperature

binary

T07, T11, T12, T13, T14, T15

I25

Coolant Temperature Analog

analog

T13, T14, T15

I29

Fuel Level SD

Binary

T07, T11, T12, T13, T14, T15

Dimensions

Case dimensions: 118mm x108mm x 40mm

Panel Cutout: 96mm x 96mm

WARNING!

If D+ is not used, connect this terminal to battery positive!

ComAp,a.s.

Kundratka 2359/17

180 00, Praha 8

Czech Republic

InteliNano-NT MRS, SW version 1.5, ©ComAp –September 2013 2

InteliNano-NT-MRS-1.5-Fast User Guide.pdf

Setpoints

Use ▲and ▼buttons to move or change value. Start button to select setpoint or confirm changes and Stop button to go back.

Basic settings

Setpoint

code

Setpoint name

B01

Nominal Voltage Ph-N

80 –480 V

B02

Nominal Voltage Ph-Ph

80 –600 V

B03

Nominal Frequency

50 Hz (1), 60 Hz (2)

B04

Connection Type

Mono Phase (1), SplitPhase (2),

3Ph3Wire (3), 3Ph4Wire (4)

B05

Units Format

Metric unit format (1), US unit

format (2)

B07

Zero Power Mode Delay

0-360 min

B08

Light Tower Mode

Disable (1), Enable (2)

B09

Nominal RPM

100-4000

Engine parameters and protections

Setpoint

code

Setpoint name

E01

Prestart Time

0-600 s

E02

Maximum Cranking Time

0-60 s

E03

Cooling Time

0-3600 s

E04

Oil Pressure Shutdown

0-10 Bar

E05

Coolant Temperature Shutdown

0 -150 °C

E15

Fuel Level Shutdown

0 –20%

E06

Battery Undervoltage

8 –40 V

E07

Warning Maintenance

0 –10000 h

E08

Oil Pressure Starter Disengagement

Disable (1), Enable (2)

E09

Choke Time

0 –3600 s

E10

Minimal Stabilization Time

1 –300 s

Generator protections

Setpoint

code

Setpoint name

G01

Generator Overvoltage Shutdown

G02 –200 %

G02

Generator Undervoltage Shutdown

0 - G01 %

G03

Generator Overfrequency Shutdown

G04 –130 %

G04

Generator Underfrequency Shutdown

0 –G03 %

To apply all changes return to the main setup menu and restart the controller by pressing the Stop button.

Alarms and Events

Events

Manual Start

Remote Start

Manual Stop

Remote Stop

Auto On

Auto Off

Power On

Island Operation

Warnings

Warning Maintenance

Low Battery

Low Fuel Level

External Warning 1

External Warning 2

External Warning 3

ECU Communication Error

Shutdowns

Emergency Stop

Overspeed

Underspeed

Low Oil Pressure

High Coolant temperature

External Shutdown 1

External Shutdown 2

External Shutdown 3

GCB Fail

Generator Overvoltage

Generator Undervoltage

Generator Overfrequency

Generator Underfrequency

Generator CCW Rotation

Start Fail

Stop Fail

Battery Flat

Fuel Level SD

ECU

For ECU configuration use PC software NanoEdit. For more details see InteliNano AMF Reference Guide.

Technical data

Power supply range

6-36 VDC

Power supply drop-out immunity

100 ms

Power consumption

35 –295 mA

Zero Power Mode consumption

52 - 344 µA

Operating temperature

-20... 70 °C

Operating humidity

95% non-condensing (IEC/EN 60068-2-30)

Protection degree (front panel)

IP65 with GASKET 4x405 only

IP50 without gasket

Storage temperature

-30... 80 °C

Binary outputs (up to 4)

Low current outputs (2)

500 mA

High current output (2)

6 A (long term) / 10 A (short term)

Total output current

10 A (long term) / 16 A (short term)

Binary inputs (up to 6)

Input resistance

1,5 kΏ

Closed contact voltage

<2 V

Open contact voltage

>3,5 V

Analog inputs (up to 3)

Galvanic insulation

Not insulated

Electrical range

0 - 2500 kΏ

Resolution

0,1 Ώ

Precision

2 % ± 3 Ώ

Charging alternator preexcitation circuit

Excitation current

100 mA

Charging fail threshold

80 %

Generator/Mains measurements

Measurement input

3ph generator voltage

Measurement type

True RMS

Voltage range

480 V Ph-Ph (277 V Ph-N)

Max. measured voltage

340 V Ph-N

Voltage accuracy

Frequency range

40 –70 Hz

Frequency accuracy

1 %

Other manuals for InteliNano NT MRS

Other ComAp Controllers manuals

ComAp

ComAp InteliGen NTC Use and care manual

ComAp

ComAp InteliGen 200 Manual

ComAp

ComAp IG-NT User manual

ComAp

ComAp InteliDrive Mobile User manual

ComAp

ComAp InteliNano NT Plus User manual

ComAp

ComAp InteliVision 5 CAN User manual

ComAp

ComAp InteliLite 4 AMF 20 User manual

ComAp

ComAp InteliDrive DCU Marine User manual

ComAp

ComAp ECON-4 Instruction manual

ComAp

ComAp InteliSys NT Programming manual

ComAp

ComAp IGS-NT Series User manual

ComAp

ComAp InteliNano NT MRS User manual

ComAp

ComAp InteliLite4 AMF20 Manual

ComAp

ComAp InteliDrive FLX LITE User manual

ComAp

ComAp IG-NT GC User manual

ComAp

ComAp IG-NT-BB User guide

ComAp

ComAp InteliDrive DCU Industrial User manual

ComAp

ComAp ECON-4 User manual

ComAp

ComAp InteliLite MRS10 User manual

ComAp

ComAp InteliLite MRS16 User manual

ComAp

ComAp InteliSys NTC BaseBox Use and care manual

ComAp

ComAp InteliLite 4 MRS16 Manual

ComAp

ComAp InteliDrive DCU Marine User manual

ComAp

ComAp InteliLite NT MRS User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual