Code Alarm CATX110 Operating instructions

Model CATX110

Programming Guide

The keychain transmitters included with the system have

been pre-programmed at the factory, with each button pre-

assigned to control a specific function of the system.

It is important to remember that during programming, each

individual step of the procedure must be executed within 15

seconds of the previous step.

When the 15 second time limit is allowed to expire, the

system will automatically terminate the programming mode.

This is indicated by a long chirp from the siren.

Additionally, the system will store codes from up to 4

different transmitters. If a 5th transmitter is programmed to

any receiver channel, then the first transmitterprogrammed

to that channel will be erased from the system’s memory.

To program new or additional transmitters, the alarm must

be disarmed and the valet switch must be in the OFF

position:

1. Enter the vehicle, and turn the ignition key to the ON

position.

2. Flip the valet switch ON then OFF 3 times

3. The dash LED will flash one time, and the sounding

device will beep one time, indication the system is ready to

accept programming for receiver channel 1.

4. Press and hold the Arm/Disarm Icon button until the

sounding device emits a long beep, indicating the signal

has been stored into memory.

5. If you have additional transmitters (up to 4) that need to

be programmed, repeat step 4 for each transmitter.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote transmitter should last

approximately one year, depending on usage. When the battery begins to

weaken, you will notice a decrease in range, or the distance from your vehicle

that your remote transmitter will operate. Follow the instructions below to

change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the remote

control. Twist the coin to pry the remote control halves apart.

2. Remove the old battery and replace with a new one. Besure to

observe the (+) and (-) signs in the battery compartment.

3. Carefully snap the case halves back together, then test the

remote control.

Model CATX110

Programming Guide

Table of contents

Other Code Alarm Car Alarm manuals

Code Alarm

Code Alarm F20 User manual

Code Alarm

Code Alarm PROFESSIONAL CA 1045 User manual

Code Alarm

Code Alarm ca1554 User manual

Code Alarm

Code Alarm CA 1150 User manual

Code Alarm

Code Alarm ca 1151 User manual

Code Alarm

Code Alarm CSI-200 User manual

Code Alarm

Code Alarm PowerCode PC 6100 User manual

Code Alarm

Code Alarm CSI-300 User manual

Code Alarm

Code Alarm CA 1550 User manual

Code Alarm

Code Alarm SRT 5500 User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES CA 1551 User manual

Code Alarm

Code Alarm ELITE Series User manual

Code Alarm

Code Alarm CA611 User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm CATX2LCD Operating instructions

Code Alarm

Code Alarm ca 1552 Professional Series User manual

Code Alarm

Code Alarm SRT 1600 User manual

Code Alarm

Code Alarm CA-670 User manual

Code Alarm

Code Alarm CA 6551 SST User manual

Code Alarm

Code Alarm CA 671 User manual

Code Alarm

Code Alarm CATX510 Operating instructions

Code Alarm

Code Alarm Professional ca6153 User manual

Code Alarm

Code Alarm CA-230 User manual

Code Alarm

Code Alarm CA-640 User manual

Popular Car Alarm manuals by other brands

Clifford

Clifford 3606X owner's guide

Ultra Start

Ultra Start 2500M SERIES install guide

Ultra Start

Ultra Start 650 Series owner's manual

Audiovox

Audiovox Prestige Platinum+ APS-511C owner's manual

Sparkrite

Sparkrite SRA8 Guide

Viper

Viper 4708V owner's manual

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Installation and maintenance manual

Falcon

Falcon Predator XL3 Installer manual

Audiovox

Audiovox Auto Security XR91 Programming guide

Clifford

Clifford Sabre II owner's manual

CrimeStopper

CrimeStopper CS-8717 Wiring diagram

Ultra Start

Ultra Start 450 SERIES install guide

Scytek electronic

Scytek electronic Vectra X3 product manual

Excalibur

Excalibur AL-1860-EDPB Operation guide

Clifford

Clifford CYBER 2 owner's manual

Gemini

Gemini 7057 user manual

FlashLogic

FlashLogic FLRSBA PRESTIGE Product guide

Magicar

Magicar FAI-440 manual