CNB SxB2xZ12F N User manual
Compact PTZ Dome Camera SxB2xZ12F(N/P)
User’s Manual Ver 1.2 (3810-0287A2)
www.cnbtec.com
Compact PTZ Dome Camera SxB2xZ12F(N/P)
User’s Manual Ver 1.2
www.cnbtec.com
This lightning flash with arrowhead symbol is intended to alert the
user to the presence of un-insulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
◎Read all of the safety and operating instructions before using the product.
◎Save these instructions for future reference.
◎Do not use attachments or accessories unless recommended by the appliance
manufacturer as they may cause ha ards, damage product and void warranty.
◎Do not use this product near water or moisture.
◎Do not place or mount this product in or on an unstable or improperly supported location.
Improperly installed product may fall, causing serious injury to a child or adult, and
damage to the product. Use only with a mounting device recommended by the
manufacturer, or sold with the product. To insure proper mounting, follow the
manufacturer's instructions and use only mounting accessories recommended by
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICEING TO UALIFIED SERVICE PERSONAL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
Important Safeguard
Warnings Cautions
a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the
presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD,
DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE.
manufacturer's instructions and use only mounting accessories recommended by
manufacturer.
◎This product should be operated only from the type of power source indicated on the
marking label.
◎Before using, make sure power supply and others are properly connected.
◎While operating, if any abnormal condition or malfunction is observed, stop using the
camera immediately and then contact your local dealer.
◎Do not disassemble or tamper with parts inside the camera.
◎Do not drop or subject the camera to shock and vibration as this can damage camera.
◎Care must be taken when you clean the clear dome cover. Especially, scratch and dust
will ruin your quality of camera.
◎Do not install the camera in areas of extreme temperature, which exceed the allowable
range.
◎Avoid installing in humid or dusty places.
◎Avoid installing in places where radiation is present.
◎Avoid installing in places where there are strong magnetic fields and electric signals.
◎Avoid installing in places where the camera would be subject to strong vibrations.
◎Never expose the camera to rain and water.
Precautions
Features
Product
Installation
Operation
MENU
Check points before operation ------------------------------------------------------------------ 20
Preset and Pattern Function Pre-Check ------------------------------------------------------ 20
Each protocol function number ------------------------------------------------------------------- 20
Starting OSD Menu --------------------------------------------------------------------------------- 21
Reserved Preset
-------------------------------------------------------------------------------------
21
------------------------------------------------- 6 -------------------------------------------- 26
General Rules of Key Operation for Menu ---------------------------------------------- 26
MAIN MENU ------------------------------------------------------------------------------------- 26
DISPLAY SETUP ------------------------------------------------------------------------------- 27
CAMERA SETUP ------------------------------------------------------------------------------ 28
MOTION SETUP ------------------------------------------------------------------------------- 32
PRESET SETUP ------------------------------------------------------------------------------- 34
SWING SETUP --------------------------------------------------------------------------------- 36
PATTERN SETUP ----------------------------------------------------------------------------- 36
GROUP SETUP -------------------------------------------------------------------------------- 37
SYSTEM INITIALIZE -------------------------------------------------------------------------- 40
------------------------------------------------- 8
------------------------------------------------- 9
------------------------------------------------- 20
Specifications
----------------------------------
42
Reserved Preset
-------------------------------------------------------------------------------------
21
PRESET ----------------------------------------------------------------------------------------------- 21
SWING ------------------------------------------------------------------------------------------------- 22
PATTERN --------------------------------------------------------------------------------------------- 22
GROUP ------------------------------------------------------------------------------------------------- 23
Others Functions ------------------------------------------------------------------------------------ 24
OSD Display of Main Screen --------------------------------------------------------------------- 25
Specifications
----------------------------------
42
◎ 1/4'' High Sensitivity CCD
◎ x12 Optical Zoom, x12 Digital Zoom(Max x144)
◎Day & Night, BLC (Backlight Compensation), WDR(Wide Dynamic Range),
ECL(Eclipse)
◎Auto-Focus, Manual Focus, Semi-Auto Focus.
◎Multi language OSD.
◎ 360°/sec high-speed movement to preset position.
◎ Simultaneous pan/tilt action when moving to preset locations for fast and natural
view transition.
◎ Low speed 0.05°/sec. joystick movement for accurate operation. The joystick speed
automatically changes as the zoom rate changes for easier operation.
◎ Up to 255 cameras can be connected in the same network.
◎ Pelco-D, Pelco-P, and BOSCH protocol can be used.
◎ Various camera functions can be configured through the OSD (On Screen Display)
Menu.
◎ Information such as Camera ID, Pan/Tilt location, Direction, Alarm In/Output, Preset
can be displayed.
Video Specification
Pan/Tilt Control
Multi-Language OSD Menu
PTZ Control
Alarm In/Output
7
6
automatically changes as the zoom rate changes for easier operation.
◎ 127 preset locations can be stored, and each preset location can have its own image
settings and label.
◎ 8 Swing functions. (continuously swinging in between 2 pre-set locations back and
forth)
◎ 4 Patterns (Saves specific Joystick operations and endlessly repeats them.)
◎ 8 groups (running a combination of up to 20 preset/pattern/ swing actions saved by
the user in sequence)
※Maximum numbers for each function differs in each protocol
(Refer to “Function numbers in each protocol”, Page 59)
◎ There are 4 Alarm Inputs and one alarm output.
◎ In order to filter out the external noise, use a port coupling at the input and a relay
at the output.
◎ The sensor can be set to Normaly Open or Normaly Close
◎ Sensor inputs can be DC 5~12V.
◎ Relay output can be up to AC 125V/0.5A or DC 24V/1A.
◎ A Sensor input can be configured to move the PTZ to any preset location.
Preset, Pattern, Swing, Group
◎ A numeric Camera ID can be set by the DIP switch, and the values for each switch
position are like the following:
- To set up the Camera ID, remove the lid at the
bottom of the camera by unscrewing the three screws
marked with arrows.
Basic Contents Camera ID Set Up
•Camera •Dome Cover
Or
•Camera with Sunshield •L wrench-1EA
9
8
• Maximum 255 IDs can be used from 1 to 255. Do not use address 0.
• The default address is 1.
• When using a Keyboard type controller, make sure that the address set in the
keyboard matches the camera’s ID before controlling.
Optional Contents
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off
•Rubber gasket
•Installation Guide •Manual
•PLASTIC ANKER
And mounting
bolt set 3EA
•DC or AC Adaptor
•Rubber Gasket for
Wall Mount Bracket
•Wall Mount Bracket
•Installation Guide
•Screws •L wrench-2EA
◎ The forth DIP switch position sets the termination Impedance on the camera.
◎ When the controller is far away from the camera (1:1 connection)
- An impedance mismatch can happen when the controller is far from the camera.
Set the termination impedance on the camera as well as the controller to match
the impedance.
◎
When connecting many cameras in the same network.
◎ The three DIP switch positions shown below sets the communication protocol.
Communication Protocol Termination Impedance
Use the termination Impedance in the following cases:
ON 1 2 3 4 ON 1 2 3 4
NO PROTOCOL BAUDRATE #1 #2 #3
0PELCO-D 2400bps OFF OFF OFF
1PELCO-D 9600bps ON OFF OFF
2PELCO-P 4800bps OFF ON OFF
3
11
10
◎
When connecting many cameras in the same network.
- The signal loss can happen when too many cameras are connected to the same
network. Set the termination impedance on the furthest camera only as well as
the controller. Do not turn on the termination impedance on other cameras.
◎ On the controller (Keyboard-type or DVR), make sure the same protocol and
baud rate are selected before controlling.
◎ Turn the camera’s power off before changing the protocol setting.
3
PELCO-P 9600bps ON ON OFF
4BOSCH 9600bps OFF OFF ON
Others Reserved
# 2# 1 # n
Keyboard Controller/DVR
RS-485
① Put the dome cover on the camera where the
marks on the casings line up. Tighten the 4
crews using the wrench supplied.
② Attach the rubber gasket to the surface mount
bracket and mount the bracket on the
installation surface using the screws provided.
④ Put the camera into the bracket where the
mark lines up with ‘unlocked’ (I) mark on
the bracket. Lock the camera in by slightly
turning it clockwise.
⑤ Make sure to turn the camera to the
position where the mark on the camera
lines up with ‘locked’ (II) mark on the
Installation
Installation of a basic type PTZ
13
12
③ Attach the service wire. Power & video connect
the cables.
☞ Attach the service wire properly to avoid
dropping the product to the ground.
lines up with ‘locked’ (II) mark on the
bracket.
⑥ Tighten the locking screw on the
opposite side using the L wrench. Remove
the protection cover from the dome cover.
The installation is now complete.
•With Sunshield
•Without Sunshield
Installation with a Wall Mount Bracket
① Attach the rubber gasket and Sunshield*
or Surface Mount bracket on the
Wall Mount bracket using the
screws provided.
☞ Applicable only when using
the Sunshield.
④ Put the camera into the bracket
where the mark lines up with
‘unlocked’ (I) mark on the bracket.
Lock the camera in by slightly turning
it clockwise.
⑤
Make sure to turn the camera to the
15
14
② Mount the wall mount assembly on
a wall using the bolts provided.
③ Attach the service wire. Power & video
connect the cables.
☞ Attach the service wire properly to
avoid dropping the product to the
ground.
⑤
Make sure to turn the camera to the
position where the mark on the camera
lines up with ‘locked’ (II) mark on the
bracket.
⑥ Tighten the locking screw on the
opposite side using the L wrench.
Remove the protection cover from
the dome cover. The installation is
now complete.
◎ RS-485
- Connect the RS-485 devices such as a PTZ controller or a DVR to operate the PTZ
camera. Please connect parallel when connecting multiple cameras together.
Cable Connections
- ALARM Line
- CVBS
Keyboard Controller/DVR
17
16
◎ Power
- The power rating for this product is DC 12V/1A and AC 24V/1.5A.
Please check to make sure the power supply is rated at DC 12V and more than 1A
before connecting.
◎ Video Output
- Connect the video cable to camera’s video output cable (provided).
Input Power Allowable Range Current Draw
For DC 12V model DC 12V ±10% 1A
For AC 24V model AC 24V ±10% 1.5A (When the Heater
is on)
- AC/DC Power
- 485 Line
This manual suits for next models
1
Table of contents
Languages:
Other CNB Security Camera manuals
CNB
CNB V4760N User manual
CNB
CNB NB21-7MHR-6 User manual
CNB
CNB XPEED SDN-22Z27F User manual
CNB
CNB IVP5035VR User manual
CNB
CNB LDC3050IR User manual
CNB
CNB LDM-24VF User manual
CNB
CNB XNET IGP2035F User manual
CNB
CNB Xpeed s2000 series User manual
CNB
CNB XNET IDP4000VR User manual
CNB
CNB IDP4030VR User manual
