ClimateRight CR5000ACH User manual
IMPORTANT: READ OWNERS MANUAL & INSTALLATION GUIDE CAREFULLY
BEFORE ASSEMBLY AND USE
Read and follow all safety rules and instructions before operating this equipment.
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY.
Please keep this manual for future reference.
INSTALLATION
INSTRUCTIONS
PORTABLE AIR CONDITIONER & HEATER ACH SERIES
CR2500ACH • CR5000ACH • CR10000ACH
CR10000ACH
CR2500ACH & CR5000ACH
2
INSTALLATION INSTRUCTIONS
REQUIRED TOOLS (NOT SUPPLIED)
·Electric Drill
·Pencil
·Tape Measure
·3-1/2”Bi-Metal Hole Saw (See picture at right)
·Six (6) - #6 Flat head wood or sheet metal screws, 1”length recommended.
(Customer must choose the length and supply the screws based on the thickness and type
material being screwed into.)
·Screwdriver to match screw heads
·Exterior caulk (optional)
·Hacksaw (optional)
INCLUDED PARTS
Quick Connect Hose System
A. (2) Unit Connector Flanges (Pre-mounted to ClimateRight®)
B. (4) Hose Flanges (Pre-mounted to Hoses)
C. (2) 4’Flexible Air Hose
D. (2) Building Flanges
E. (4) Flange Caps
Figure 1
Building Flange
3
INSTRUCTIONS
1. Choose a firm, flat and level location next to the structure. Be aware of anything that may
be sensitive to water as the unit will drain water from the condensation drain tube onto the
ground. The unit must be within 4’(48”) of the structure (closer, if there will be bends in
the air hose) and 6’to a 120V power outlet. The closer the unit is to the structure, the
better the airflow will be. (See Figure 2.1)
2. Place the ClimateRight unit at the chosen location. Orient the unit with the Air Inlet and
Outlet toward the structure or at a maximum of 90 degrees from the structure.
Note: It is important to face the control panel toward an area from which the remote
control will be used, but do not turn the unit so the air hoses will bend more than 90
degrees. If the unit must be turned up to 90 degrees, a gentle curve is preferred over a
sharp bend in the air hose. The sharp bend will degrade airflow and heating and cooling
capacity. All control functions will be performed from the remote control.
3. Before marking locations to drill the holes for the flanges, make sure there are no electrical
wires, pipes or obstructions of any type behind the proposed drilling locations.
4. Find a location where the first hole will be located. The hole locations should not be placed
where objects could block the air flow. Mark the first location with a pencil.
5. The second hole location is recommended to be spaced a minimum of 12”diagonally from
the first hole location. Mark this location with a pencil. (See Figure 2.2)
Figure 2.1
Figure 2.2
4
6. With no obstructions behind the marked locations, drill out the holes with the 3-1/2”hole
saw.
7. Once the holes have been drilled, insert a ClimateRight Building Flange (D).
Note: Check the length of the flange, if the Building Flange is too long, it can be cut to
length with a hacksaw. The grooves on the flange are spaced at 1”intervals.
8. If necessary, mark the screw hole locations with a pencil and drill pilot holes for the screws.
(For #6 wood screws use a 1/16”drill bit.)
9. Optional: Lay down a bead of caulk on the side of the Building Flange that will face the
building. (See Figure 3)
10. Take 3 screws and secure the Building Flange into the structure. Repeat steps 6-9 for the
second Building Flange (D).
11. The Air Hoses (C) and Hose Flanges (B) are pre-assembled at the factory. Take one of these
assemblies and extend the accordion style hose so it is long enough to reach the unit and
the structure.
12. Mate the Hose Flange (B) to the ‘Air Outlet’Unit Connector Flange (A) (See Figure 4) that is
pre-installed on the unit. Turn the Hose Flange clockwise until they “click”together.
13. Take the other side of the Air Hose and Hose Flange and install it onto the upper Building
Flange (D).
14. Install the second Air Hose onto the ‘Air Inlet’by repeating steps 11 and 12, except install
onto the lower Building Flange.
15. Take the power cord and plug the unit into a GFCI protected receptacle or a receptacle with
a weatherproof (while-in-use) cover.
16. The ClimateRight unit is now ready for use. Refer to the Owner’s Manual for instructions on
how to operate the unit.
Figure 3
Figure 4
2
Questions or concerns? For assistance,
please call Customer Service:
800-725-4628
777 Manor Park Dr. Columbus, Ohio 43228
www.climateright.com
This manual suits for next models
3
Table of contents
Other ClimateRight Air Conditioner manuals
ClimateRight
ClimateRight CR-2550 User guide
ClimateRight
ClimateRight CR13000-PAC User manual
ClimateRight
ClimateRight easyair CR12000SACH Troubleshooting guide
ClimateRight
ClimateRight CR2500ACH User manual
ClimateRight
ClimateRight easyair CR12000SACH User manual
ClimateRight
ClimateRight CR-5000-AC User manual
ClimateRight
ClimateRight easyair CR12000SACH User manual
ClimateRight
ClimateRight CR2500ACH User manual
ClimateRight
ClimateRight CR13000-PAC User manual
ClimateRight
ClimateRight CR2500ACH User manual
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu Inverter ASBA30JFC operating manual
Toshiba
Toshiba RAS-M10SMUV-E installation manual
Daikin
Daikin FXLQ20MAVE Operation manual
Hitachi
Hitachi RAS-E24CAK instruction manual
CIAT
CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance
Bestron
Bestron AAC6000 instruction manual
