ClearCube M1032W User manual

Page 1 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

M1032W

Engineering Workstation

Quick Start Guide

Container Contents

Included in

container

The list below shows components included in an M1032W Engineering Workstation container.

M1032W Engineering Workstation

Chassis mounting rails and hardware

GPU graphics card

Mini-DisplayPort-to-DisplayPort cables (× 2 or × 4 depending on configuration)

Power cable

TERA2 PCoIP®host card

This Quick Start Guide

GPU and motherboard documentation

Not included

The list below shows items not included with an M1032W Engineering Workstation.

PCoIP zero client(s)

Monitors

Ethernet cables

Keyboard and mouse

Page 2 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

M1032W Overview and Features

M1032W

overview

The M1032W Engineering Workstation is a 1U, GPU-optimized, high-performance engineering workstation

based on the Intel®C612 chipset. The list below shows M1032W features.

Intel Xeon®E5-2600 v3-series processor (up to 10 cores and 145 W)

8 × DIMM slots, 288-pin DDR4, 1.2 V

Up to 256 GB DDR4 ECC RDIMM at 2133, 1600, or 1333 MHz

Up to 512 GB DDR4 ECC LRDIMM at 2133, 1600, or 1333 MHz

Supports 64-GB, 32-GB, 16-GB, 8-GB, 4-GB, and 2-GB DIMMs

6 × 2.5-inch SATA hot-swap drive bays

RAID support:

0, 1, 5, and 10 on Windows®operating systems

0, 1, and 10 on Linux®operating system

3 × Ethernet ports (2 × LAN ports and 1 × dedicated IPMI port)

Support for IPMI 2.0

Continued on next page

Page 3 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

M1032W Overview and Features, Continued

M1032W front

panel

The picture and table below show indicators and buttons on the front panel of an M1032W.

Indicator

Button

Description

Information

LED

Information. Shows several states:

Status

Description

Red, continuous

Overheat condition.

Check cables.

Red, flashing

(every second)

Fan failure.

Check fan.

Red, flashing

(every4seconds)

Power failure. Check

power supply.

Blue, continuous

Local Unit Identifier

(UID) button has

been pressed. Use to

aid identification in

rack mount.

Blue, flashing

Remote UID is on.

Use to identify unit

from remote location.

NIC 2

Flashing: network activity.

NIC 1

Flashing: network activity.

HDD

Flashing: hard disk drive activity.

Power

(Indicator)

Continuous: power is supplied to M1032W.

UID

(Button)

Unit Identifier. Press to illuminate blue

LEDs on front panel and rear of chassis to

ease identification in rack mounts. LED

remains on until button is pressed again.

Power

(Button)

Press to power on and power off M1034W.

Continued on next page

Page 4 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

M1032W Overview and Features, Continued, Continued

M1032W rear

ports and

connectors

The picture below shows ports, connectors, and buttons on the rear of an M1032W.

Description

GPU

Graphics

Card

DisplayPorts (number varies by configuration)

Dual-link DVI-I port (× 1, not on all configurations)

Dedicated IPMI LAN port

USB 3.0 port 0

USB 3.0 port 1

Ethernet LAN 1 port

Ethernet LAN 2 port

COM port

VGA port

Unit ID Button (press to illuminate LED for visual identification in rack)

Optional fiber NIC

PCoIP

Host

Card

Mini DisplayPorts (× 2 or × 4, number varies by configuration)

Dedicated PCoIP LAN port

Power connector

GPU Graphics Card

(Varies by Configuration)

PCoIP Host Card

(Varies by Configurations)

Page 5 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

Rack Rails and Mounting

Rack rail

components

Two rack rail assemblies are included with an M1032W Engineering Workstation. Each assembly has

two sections:

Inner rails: attach to the workstation chassis (the inner rail is pre-attached), and

Outer rack rails: attach to rack

The picture below shows the inner chassis rails and the outer rack rails.

Continued on next page

Inner Rail

Pre-Assembled

Inner Rail Extension

Attach to Chassis

Outer Rack Rails

Slide Front into Rear and Attach

Front and Rear Brackets to Rack

Front Bracket

Rear Bracket

Page 6 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

Rack Rails and Mounting, Continued

Install inner

rail extensions

The picture and table below show how to attach and secure the inner rail extensions.

Step

Action

Align the hooks on the side of the chassis with the slots on the inner rail extension.

Slide the extension rail toward the front of the chassis.

Secure the extension rail with the screws provided.

Repeat these steps to attach the other extension rail on the other side of the chassis.

Next step: assemble outer rack rails.

Assemble

outer rack rails

Outer rack rails consist of two sections: a longer front section and a shorter rear section. Slide these together to

assemble the rail.

Step

Action

Identify the left and right outer rack rails by examining the ends (brackets). These brackets

bend outward as shown in “Rack rail components.”

Slide the front section of the outer rack rail into the rear outer rack rail as shown in “Rack rail

components.”

Repeat these steps to assemble the other outer rack rail.

Next step: install outer rack rails in a rack.

Continued on next page

Step 1

Step 2

Step 3

Page 7 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

Rack Rails and Mounting, Continued

Install outer

rack rails

The picture and table below shows how to install the assembled outer rack rails in a rack.

Step

Action

Adjust the outer rack rails so that the outer rails

fit snugly in the rack.

Align the holes on the front of the outer rail with

the holes on the front of the rack and secure with

the screws provided (see Ain the adjacent

picture).

Align the holes on the rear of the outer rack rail

with the holes on the rack and secure with the

screws provided (see Bin the adjacent picture).

Repeat these steps with the other outer rack rail

assembly.

Next step: Install the workstation in a rack.

Installing in

rack

To install an M1032W Engineering Workstation in a rack:

1. While carefully lifting the workstation, slide the inner rail extensions into the front of the outer rack rails.

2. Push the workstation into the rack until it clicks into the locked position.

Removing

from rack

This picture and table below show how to remove an M1032W Engineering Workstation from a rack.

1. Press the outer rack rail latch to release the workstation chassis

(the latch is shown in the adjacent picture).

2. Carefully slide the chassis forward off of the outer rack rails and

out of the rack.

Page 8 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

Setting up an M1032W Engineering Workstation

M1032W

cabling

This section shows how to connect cables. Numbers in parentheses correspond to labels shown in “M1032W

front panel” and in “M1032W rear ports and connectors”to ease identification.

Step

Action

Install the included mounting rails to the server chassis and then install the chassis in a rack.

From the rear of the chassis, use the included video cables to route video from the PCoIP host

card to the GPU. Use the included DP-to-mini-DP cables.

“Cabling diagrams” below shows pictures of every GPU and PCoIP Host Card combination.

Find your configuration in the table’s Card Configuration column and connect cables as shown

in the corresponding picture.

Connect an Ethernet cable to the dedicated PCoIP LAN port (20) and connect the other end

to a network router or switch.

Optionally, connect one or more Ethernet cables to the LAN ports (13) and (14) on the rear

of the chassis and connect the other end of the cable(s) to a network router or switch.

If your configuration includes a fiber NIC (18), connect a fiber Ethernet cable to the Fiber

NIC (18) on the rear of the chassis and connect the other end of the cable to a network

router or switch.

Optionally, connect one or more Ethernet cables to the Dedicated IPMI port (10) on the

rear of the chassis and connect the other end of the cable to a network router or switch.

From the rear of the chassis, connect the included power cable to the power connector

(21) on the rear of the server, and connect the power cable to a power outlet.

From the front of the chassis, press the power button (7) to power on the server.

Continued on next page

Page 9 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

Setting up an M1032W Engineering Workstation, Continued

Cabling

diagrams

This section shows how to connect cables between the GPU and PCoIP Host Card for each M1032W

configuration. Connect video cables on the rear of your workstation according to the configuration you ordered.

In the table below, DP indicates DisplayPort and Mini-DP indicates mini-DisplayPort.

NOTE: Host card mini-DP ports are ordered from 1 (rightmost) to 4 (leftmost). Be sure to use ports as

shown below when connecting cables from the host card to the GPU (using different ports can

cause display issues).

Card

Configuration

Displays

Resolution

Diagram

K1200 GPU and

Quad PCoIP Host Card

1920 × 1200

2560 × 1600

K2200 GPU and

Quad PCoIP Host Card

2560 × 1600

Continued on next page

Page 10 of 15 P/N G0200177 Rev A, 1.0.03.03.2016

ClearCube Technology, Inc. 3700 W Parmer Lane Austin, TX 78727 (512) 652-3500 www.clearcube.com

Setting up an M1032W Engineering Workstation, Continued

Cabling diagrams (continued)

Card

Configuration

Displays

Resolution

Diagram

K2200 GPU and

Dual PCoIP Host Card

1920 × 1200

2560 × 1600

M4000 GPU and

Quad PCoIP Host Card

1920 × 1200

2560 × 1600

Continued on next page

Table of contents

Other ClearCube Desktop manuals

ClearCube

ClearCube Eon e100 Technical manual

ClearCube

ClearCube A6106HL User manual

ClearCube

ClearCube Eon e100 Technical manual

ClearCube

ClearCube Capio One User manual

ClearCube

ClearCube Thin Client I8520 User manual

ClearCube

ClearCube CD7800 Series User manual

ClearCube

ClearCube Eon e100 User manual

ClearCube

ClearCube Thin Client CD8826 User manual

ClearCube

ClearCube CD1020 Series User manual

ClearCube

ClearCube Cloud Desktop CD9500 series User manual

ClearCube

ClearCube CD10 Series User manual

ClearCube

ClearCube ClientCube 3 User manual

Popular Desktop manuals by other brands

HP m9060n - Pavilion - Elite Quick setup

Asus

Asus E210 Series user guide

Dell

Dell Inspiron 600m quick start

Dell

Dell Inspiron 3662 Service manual

TotalFlow

TotalFlow uFLO user manual

HP Presario SV7000 - Desktop PC manual

HP ProDesk 400 G5 Maintenance and service guide

Logitech

Logitech MK320 quick start guide

Dell

Dell XPS 730 H2C Service manual

Sony

Sony Vaio Series operating instructions

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer quick start

Alto

Alto MD 250 instruction manual

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series user manual

Sony

Sony VAIO VGX-TP1 Series user guide

Asus

Asus Eee Box B204 user manual

Dell

Dell Optiplex 9010 All In One owner's manual