Clarke Contractor CON1500RDV Instruction Manual

OPERATION & MAINTENANCE

INSTRUCTIONS

LS1215

ROTARY HAMMER DRILL

MODEL NO: CON1500RDV

PART NO: 6479605

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Hammer Drill. The CRD1500RDV is

designed for general drilling/masonry drilling/chiselling/drill & hammer use in

trade and light industrial applications.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

INVENTORY

1 Blow-moulded Case 9 150 mm x 12 mm TCT Drill Bit

2 1500 Watt Rotary Hammer 10 Dust Shield Cup

3 Side Handle Assembly (fitted) 11 13 mm Keyed Chuck

4 Depth Stop Rod 12 SDS+ Chuck Adaptor (fitted to 13

mm chuck and including L.H.T.

retaining screw)

5 250 mm Bull Point Chisel 13 Chuck Key

6 250 mm x 20 mm Flat Chisel 14 Pin Wrench

7 150 mm x 8 mm TCT Drill Bit 15 Accessory Storage Box

8 150 mm x 10 mm TCT Drill Bit 16 Pot of Grease (for SDS+ Chuck & Bit

Shanks)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

WORK AREA

1. Keep work area clean and well lit. Cluttered and dark areas invite

accidents.

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges or refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

2. Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

3. When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in personal injury.

2. Use safety equipment. Always wear eye protection. Safety equipment such

as dust mask, non-skid safety shoes, or hearing protection used for

appropriate conditions will reduce personal injuries.

3. Avoid accidental starting. Ensure the switch is in the off position before

connecting to the power supply.

4. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL

INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/

OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED

BELOW REFERS TO YOUR HAMMER DRILL.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

5. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the power before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

4. Store idle tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Poorly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

7. Use the power tool and accessories in accordance with these instructions

and in the manner intended for the particular type of power tool, taking

into account the working conditions and the work to be performed. Use of

the power tool for operations different from intended could result in a

hazardous situation.

SERVICE

1. Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Read instruction

manual before use

Wear dust mask

Class 2 Double

Insulated

Wear ear defenders

CE Mark Wear safety glasses

Weee Directive

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity

supply is the same as that indicated on the rating plate. Connecting it to any

other power source may cause damage.

If it is necessary to change the fuse in the plug, the fuse cover must be refitted.

If the fuse cover becomes lost or damaged, the plug must not be used until a

suitable replacement is obtained.

If the plug has to be changed due to damage, a replacement should be

fitted, following the wiring instructions shown below. The old plug must be

disposed of as insertion into a mains socket could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond

with the markings on the terminals of your plug, proceed as follows.

• The wire which is

coloured Blue must be

connected to the

terminal which is

marked Nor coloured

Black.

• The wire which is

coloured Brown must

be connected to the

terminal which is

marked Lor coloured

Red.

We strongly recommend that this machine is connected to the mains supply via

a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

This symbol indicates that this is a Class II product, and does not require

an earth connection.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

a 5 Amp

the cable is firmly held by the clamp

fuse

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 SDS Chuck 6 Speed Control

2 Rotation Stop Switch 7 Motor

3 Grease Port Cover 8 Front Handle

4 Trigger 9 Depth Stop

5 Hammer Action Selector

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

POSITIONING THE FRONT HANDLE

The front handle can be positioned

left, right or centre as required.

1. Loosen the handle by twisting it

clockwise (when viewed from

above).

2. Rotate the handle to the required

position.

3. Secure the handle by twisting it

anticlockwise (when viewed from

above).

FITTING THE DEPTH STOP

The depth stop is fitted within the

front handle and can only be used if

this handle is fitted.

1. To install the depth stop, undo the

thumbscrew until the depth stop

can be passed through the

opening.

2. To set the depth stop, release the

thumbscrew and slide the rod in

and out to the required position.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INSERTING A DRILL BIT / CHISEL

The chuck clamps SDS drill bits and chisels without the need for a chuck key.

1. Pull back the collar and Insert the

bit.

• Turn the bit in the chuck until it

latches.

2. Release the collar to lock in

place.

3. Check by pulling the bit to see if it

is locked in place.

IMPORTANT: Always clean the shaft

of the drill bit before inserting into the chuck.

IMPORTANT: Do not allow dust or debris inside the chuck as this will cause

problems in the future.

REMOVING A BIT

1. Slide the collar to the rear and pull the bit out the chuck.

CAUTION: WHEN REMOVING A BIT FROM THE DRILL, REMEMBER THAT IT

MAY BE EXTREMELY HOT. EITHER ALLOW IT TO COOL DOWN FIRST OR USE

INDUSTRIAL GLOVES TO REMOVE THE BIT.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SELECTING THE OPERATING MODE

HAMMER ACTION SELECTOR

1. With the drill not operating, set the

hammer action selector to the

required setting.

• Left - Hammer Assisted Drilling

• Right - Drill Only

IMPORTANT: When using the

“hammer action” you only need to

apply light pressure. Too much pressure will place unnecessary load on the

motor. Check the drill bits regularly, re-sharpen or replace if required.

ROTATION ON/OFF SELECTOR

Some jobs require the chuck to

remain stationary yet still have the

hammer effect, such as chiselling

concrete, plaster etc.

• Set the rotation selector to the

right for “no rotation”.

• Set the rotation selector to the

left for “normal rotation”.

CAUTION: THESE OPERATIONS SHOULD ONLY BE PERFORMED WHEN THE

DRILL IS AT A COMPLETE STOP.

Mode Hammer Action selector Rotation selector

Drill Only Drill Only ON

Hammer Drill Hammer Assisted Drilling ON

Hammer only (no rotation) Hammer Assisted Chiselling OFF

Table of contents

Other Clarke Drill manuals

Clarke

Clarke RAD1 User manual

Clarke

Clarke CDS1 User manual

Clarke

Clarke X-Pro CAT207 Installation and operation manual

Clarke

Clarke CHD820 Instruction Manual

Clarke

Clarke CAT87 Installation and operation manual

Clarke

Clarke CAT116 Instruction Manual

Clarke

Clarke Contractor CON24 Installation and operation manual

Clarke

Clarke CAT27B Installation and operation manual

Clarke

Clarke 3110835 Installation and operation manual

Clarke

Clarke CONTRACTOR CON720RHD Instruction Manual

Clarke

Clarke CMD300 Manual

Clarke

Clarke CCD30LIC Instruction Manual

Clarke

Clarke X-pro CAT158 Installation and operation manual

Clarke

Clarke CAT60 Installation and operation manual

Clarke

Clarke SCD28 User manual

Clarke

Clarke CAT100 Installation and operation manual

Clarke

Clarke CRD1250 User manual

Clarke

Clarke CAT123 Instruction Manual

Clarke

Clarke CHD500 Installation and operation manual

Clarke

Clarke Metalworker CMD10 Manual

Clarke

Clarke CRD1250 Instruction Manual

Clarke

Clarke CON18LI Instruction Manual

Clarke

Clarke CMD300 Instruction Manual

Clarke

Clarke Air CAT68 Instruction Manual

Popular Drill manuals by other brands

Makita

Makita BDF456 instruction manual

Black & Decker

Black & Decker LDX220 instruction manual

Hitachi

Hitachi DH 40MA Handling instructions

Challenge

Challenge JO Instructions and parts manual

Makita

Makita LXFD01 instruction manual

Festool

Festool T18+3 instructions

Milwaukee

Milwaukee M12 FPDX-202X Original instructions

EINHELL

EINHELL TE-RH 32 E operating instructions

Makita

Makita DHP484 instruction manual

Makita

Makita FD05 instruction manual

Bosch

Bosch PSB 530 RA operating instructions

Maximum

Maximum 054-1359-4 instruction manual

Makita

Makita HP332D instruction manual

Raider

Raider RDP-HD31H user manual

Bort

Bort BPM-1400x2 manual

Black & Decker

Black & Decker 7266 owner's manual

KENT USA

KENT USA TRD1230 Operation manual

Bosch

Bosch GSB 19-2 RE Original instructions