Cisco 1100 Series User manual

Install and Upgrade Internal Modules and Field

Replaceable Units

The Cisco 1100 Series Integrated Services Routers have internal modules and field-replaceable units (FRUs)

that can be quickly and easily removed and replaced without having to send the entire router for repair.

This section describes how to install and upgrade the internal modules and FRUs in the Cisco 1100 Series

ISRs. The information is contained in the following sections:

•Access Internal Modules, on page 1

•Locate Internal and External Slots for Modules, on page 3

•Install an LTE Pluggable Module, on page 3

•Install and Remove Small Form Pluggable Modules, on page 10

Access Internal Modules

To access the internal modules on the router, you must first disconnect the power source and then remove the

chassis cover. See the Replacing the Chassis Cover section for instructions on how to remove and later

replace the chassis cover on the routers.

Only trained and qualified personnel should be allowed to install, replace or service this equipment. Statement

1030.

Warning

Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network

voltages. Statement 1041.

Warning

Power off the unit before you begin. Statement 237.

Warning

Install and Upgrade Internal Modules and Field Replaceable Units

Replace the Chassis Cover

The Cisco 1100 Series ISRs have a removable cover. Do not attempt to run the router without the cover. This

can cause the router to overheat very quickly. To remove the chassis cover, use a number-2 Phillips screwdriver

and perform the following tasks:

Remove the Cover

To remove the cover, perform the following steps:

Step 1 Disconnect the power supply before you perform any module replacement.

Step 2 Confirm the router is turned off and disconnected from the power supply.

Step 3 Disconnect all port cables so that that no one works on the unit with attached cable in the event of lightning or surges.

Step 4 Place the chassis on a flat surface.Remove the fourteen cover screws on the two sides of the router cover.

Step 5 Slide the cover from bezel side to I/O side until it stops. Remove all screws on both sides of the router; there are seven

screws on each side.

Step 6 Pull the cover to disengage the slots along the front (bezel) edge of the chassis, as shown in this figure.

Slots

Screw holes (7 numbers on each side)

Install and Upgrade Internal Modules and Field Replaceable Units

Replace the Chassis Cover

Replace the Cover

The covers are an integral part of the safety design of the product. Do not operate the unit without the covers

installed. Statement 1077

Warning

To replace the cover, perform the these steps:

Step 1 Disconnect the power supply before you begin replacing the chassis cover.

Step 2 Confirm that the router is turned off and disconnected from the power supply (or power supplies) if there is redundant

power supply.

Step 3 Disconnect all port cables to ensure that no one works on the unit with attached cable in the event of lightning or surges.

Step 4 Place the chassis on a flat surface.

Step 5 Locate the cover hooks on the mating slots and slide the cover towards the bezel side.

Step 6 Secure seven screws on each side.

Locate Internal and External Slots for Modules

This section describes the locations of internal modules on the router motherboard.

Install an LTE Pluggable Module

To reduce the risk of electric shock, the chassis of this equipment needs to be connected to permanent earth

ground during normal use Statement 445

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages

and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other

equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all

cards, faceplates, front covers, and rear covers are in place. Statement 1029.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement

1030

Warning

Install a Micro-SIM Card onto a USB LTE Dongle

This section describes how to insert a micro-SIM card into a USB LTE dongle in a C1101-4P router.

Install and Upgrade Internal Modules and Field Replaceable Units

Replace the Cover

Figure 1: Micro-SIM Card Slot with Dust Cover

Step 1 To insert a micro-SIM card into a USB LTE dongle, do these steps:

a. Tap open the micro-SIM protective cap on the USB dongle, gently insert the micro-SIM card with its edge oriented

as shown in the figure until the SIM is seated in the socket.

b. Tap close the micro-SIM protective cap on the USB to close the slot.

Step 2 To remove a micro-SIM card into a USB LTE dongle, do these steps:

a. Tap open the dust cover, and then gently push the micro-SIM card to eject the card from the SIM slot.

b. Tap close the micro-SIM protective cap on the USB to close the slot.

The antenna orientation may need to be adjusted for optimal performance.

Note

Perform the following steps to insert the USB LTE dongle with the SIM card into a horizontal slot on the rear

panel of a C110x series router:

1. Ensure the micro-SIM is installed in the LTE USB dongle.

2. Plug the LTE USB dongle into the magnet holder.

3. Attach the magnet holder into the USB port on the metal front panel of C1101-4P.

Install and Upgrade Internal Modules and Field Replaceable Units

Install a Micro-SIM Card onto a USB LTE Dongle

Figure 2: LTE USB 2.0 Dongle for C1101-4P

DescriptionNumber

Supporting ring1

Magnet2

Extend outward 30mm3

Plug-in direction4

DescriptionNumber

Supporting ring1

Dongle holder with magnet2

Router-C1101-4PLTEPW3

Install and Upgrade Internal Modules and Field Replaceable Units

Install a Micro-SIM Card onto a USB LTE Dongle

Follow the same procedure to install the USB LTE dongle onto routers with a vertical USB slot.

Install an LTE Pluggable Module on a C1101-4P

To insert the LTE pluggable module into the router, do these steps:

Step 1 Insert and then gently push the LTE pluggable into the pluggable slot of C1101-4P until firmly fixed.

Step 2 Tighten the screw, the recommended torque is 10-12 in-lb.

Figure 3: LTE Pluggable - C1101-4P

DescriptionItem

GPS Antenna1

LTE Antenna2

Ground Lug3

Kensingston Lock Slot4

Install and Upgrade Internal Modules and Field Replaceable Units

Install an LTE Pluggable Module on a C1101-4P

Figure 4: LTE Pluggable - C1127X-8PLTEP

DescriptionItem

GPS Antenna1

LTE Antenna2

Ground Lug3

Kensingston Lock Slot4

Install and Upgrade Internal Modules and Field Replaceable Units

Install an LTE Pluggable Module on a C1101-4P

Figure 5: LTE Pluggable - C1118-8PLTEP

DescriptionItem

Mini-PCIE1

Common heat spreader + thermal interface2

I/O3

Enclosure base to support 4-antenna4

4-1 SMA-MHF4 cable assembly5

SMA Diversity Antenna for usability and Micro-USB port access6

Figure 6: LTE Pluggable - C1118-8PLTEP Back Panel

Install and Upgrade Internal Modules and Field Replaceable Units

Install an LTE Pluggable Module on a C1101-4P

Figure 7: C1118-8PLTEP with Micro SIM Slots

This section describes how to insert a Micro-SIM card into an LTE pluggable module.

To insert the Micro-SIM cards into an LTE Pluggable module:

1. Place the router on its bottom side, remove the screws and then the Micro-SIM cover from the pluggable

module.

Do not touch any part of the exposed PCB circuit area when the Micro-SIM cover is removed.

Caution

2. Push in each Micro-SIM card into the slot until it clicks.

3. Secure the Micro-SIM cover with a screw. The recommended torque is 2.8 - 3.8 inch LBF.

4. You have now successfully inserted the Micro-SIM cards into the LTE pluggable module.

Figure 8: Insert the Micro-SIM cards

Install and Upgrade Internal Modules and Field Replaceable Units

Install an LTE Pluggable Module on a C1101-4P

DescriptionItem

Micro-SIM 1 (Towards the device)1

Micro-SIM 0 (Away from the device)2

Install and Remove Small Form Pluggable Modules

This section describes how to install and remove Small Form Pluggable (SFP) modules in the Cisco 1100

Series ISRs. The information is contained in the following sections:

Install Small Form Pluggable Module

This section describes how to install optional small-form-factor pluggable (SFP) modules in the Cisco ISR1000

series Integrated Services routers to provide optical Gigabit Ethernet connectivity.

Only SFP modules certified by Cisco and complies with IEC 60825-1:2014 are supported on these routers.

For more information, refer to SFPs Supported on Cisco 1100 ISRs.

The SFP module-GLC-GE-100FX V01 is not supported on the Cisco111x Series.

Note

Class 1 laser product. Statement 1008.

Warning

Remove Small Factor Pluggable Module

To remove a small factor pluggable (SFP) module from the router:

Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not

view directly with optical instruments. Viewing the laser output with certain optical instruments (for example,

eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.

Warning

Install and Upgrade Internal Modules and Field Replaceable Units

Install and Remove Small Form Pluggable Modules

Other manuals for 1100 Series

This manual suits for next models

Table of contents

Other Cisco Wireless Router manuals

Cisco

Cisco UBR7246VXR User manual

Cisco

Cisco WRT54G2 Linksys User manual

Cisco

Cisco 4402 - Wireless LAN Controller Guide

Cisco

Cisco Linksys E900 User manual

Cisco

Cisco Linksys WRT54G3G User manual

Cisco

Cisco DPC3827 User manual

Cisco

Cisco UC540W-BRI-K9 User manual

Cisco

Cisco Linksys WRV54G User manual

Cisco

Cisco RV340W User manual

Cisco

Cisco 7246 - uBR Router Manual

Cisco

Cisco RB-WRT54GS2 - Wireless-G Broadband Router User manual

Cisco

Cisco Linksys SE1500 User manual

Cisco

Cisco Linksys X1000 User manual

Cisco

Cisco 881W - Integrated Services Router Wireless Manual

Cisco

Cisco Small Business WRP400 User manual

Cisco

Cisco RV180 Instruction Manual

Cisco

Cisco Linksys EA2700 User manual

Cisco

Cisco LINKSYS WRT54GX4 User manual

Cisco

Cisco WRT320N - Wireless-N Gigabit Router Wireless User manual

Cisco

Cisco WRT610N - Simultaneous Dual-N Band Wireless... User manual

Cisco

Cisco WRVS4400N - Small Business Wireless-N Gigabit Security... Instruction Manual

Cisco

Cisco C3201FESMIC-TP= - 3201 Fast EN Switch Mobile Interface Card Expansion... User manual

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router User manual

Cisco

Cisco WRT54G2 Linksys User manual

Popular Wireless Router manuals by other brands

Milesight

Milesight UG67 user guide

Airlogic

Airlogic AirSync Class 1 Features

Samsung

Samsung WCH730B user manual

TELEFONICA

TELEFONICA USB Adapter quick start guide

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series quick start

Askey

Askey RAC2V1K user manual

Alloy

Alloy WLF2454AP-S user guide

TP-Link

TP-Link TL-WR542G user guide

NETGEAR

NETGEAR WNR2000v4 user manual

Hama

Hama 53120 Operating instruction

Intellinet

Intellinet 524582 user manual

Asus

Asus RT-N10P user guide

D-Link

D-Link DIR-506L Quick installation guide

Sapido

Sapido GR297n user manual

Asus

Asus DSL-N55U user guide

AMTC

AMTC WR7502 user guide

Compaq

Compaq CP-2W - iPAQ Connection Point manual

SMC Networks

SMC Networks WBR14-N2 FICHE user guide