Cisco FirePOWER 8000 Series User manual

Insert and Remove a Network Module (NetMod) on

an 8000 Series FirePOWER Appliance

Document ID: 118194

Contributed by Nazmul Rajib and Josiah Zimmermann, Cisco TAC

Engineers.

Aug 06, 2014

Contents

Introduction

Prerequisites

Before You Begin

Required Tool and Hardware

Remove the Module or Slot Cover

Insert a Module or Slot Cover

Introduction

Instead of the usual fixed port configuration of most high−end security appliances, the modularity of the 8000

Series appliances enables you to choose and change the number and type of interfaces for the appliance.

Various Network Modules (NetMods) are inserted into the 8000 Series appliances to customize the interface

configuration to match your network requirements. This document describes how to insert and remove a

NetMod in an 8000 series FirePOWER appliance.

Caution: If you install a NetMod in an incompatible slot on your appliance or a NetMod is otherwise

incompatible with your system, an error or warning message appears in the web interface on the managing

Defense Center when you attempt to configure the NetMod.

Prerequisites

Before You Begin

Before you begin, prepare to insert or remove your module using the following guidelines:

Identify all appliance and module parts.• Identify the slots where you want to install your NetMods.• Identify the correct slots for your stacking modules.• Confirm that the EMI gaskets are in place.• Unplug all power cords from the appliance.•

Warning: You cannot hot−swap modules. You must power down and unplug both power cords from the

appliance before inserting or removing modules.

Caution: Use proper electrostatic discharge (ESD) practices such as wearing wrist straps and using an ESD

work surface when handling the modules. Store unused modules in an ESD bag or box to prevent damage.

Required Tool and Hardware

T8 Torx screwdriver• 8000 Series FirePOWER appliance•

Remove the Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to release the latch.

Step 3: Slide the module out of the slot.

Insert a Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to open the latch. The near end of the latch is visible. The far

end of the latch is inside the module.

Step 3: Insert the module into the slot until the far end of the latch is inside the slot and the near end of the

latch touches the outside of the slot.

Step 4: Push the lever toward the module so that the latch engages and pulls the module into the slot.

Step 5: Press firmly on the screw hole to push the lever fully against the module to secure the latch.

Step 6: Insert and tighten the reserved T8 Torx screw into the lever.

Updated: Aug 06, 2014 Document ID: 118194

Table of contents

Other Cisco Network Hardware manuals

Cisco

Cisco CATALYST 6000 Installation and operation manual

Cisco

Cisco Network Storage System NSS3000 Series User manual

Cisco

Cisco CPS-MSP-1RU-K9 User manual

Cisco

Cisco Cisco ONS 15600 SDH User manual

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... User manual

Cisco

Cisco 1230AG - Aironet - Wireless Access Point User manual

Cisco

Cisco GS7000 Operating instructions

Cisco

Cisco NCS 6008 LCC Instruction Manual

Cisco

Cisco Aironet 1040 Series User manual

Cisco

Cisco Content Delivery Engine 100/200/300/400 Manual

Cisco

Cisco RSP4+ Bootflash Memory Upgrade to 16MB... Operator's manual

Cisco

Cisco Firepower 2130 Maintenance and service guide

Cisco

Cisco ONS 15310-MA User manual

Cisco

Cisco ASR 5000 User manual

Cisco

Cisco S170 Web User manual

Cisco

Cisco ONS 15454 Series Manual

Cisco

Cisco CX-FEIP-1FX= Installation and con?guration User manual

Cisco

Cisco Meraki MX68 Manual

Cisco

Cisco SOURCEfire 3D500 User manual

Cisco

Cisco OL-7822-06 User manual

Cisco

Cisco ISE - Line Card ISE User manual

Cisco

Cisco AGS+ Instruction Manual

Cisco

Cisco ONS 15454 User manual

Cisco

Cisco NAC3350-PROF-K9 - NAC Profiler Server User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide