Cisco NTP-E157 Parts list manual

CHAPTER

11-1

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Change Card Settings

This chapter explains how to change transmission settings on cards in a Cisco ONS 15600.

Before You Begin

As necessary, complete the “NTP-E57 Document Existing Provisioning” procedure on page 7-2.

Before performing the following procedures, investigate all alarms and clear any trouble conditions.

Refer to the Cisco ONS 15600 Troubleshooting Guide as necessary.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

1. NTP-E157 Provision a Multirate PPM, page 11-2—Complete this procedure to provision a multirate

pluggable port module (PPM), for the ASAP card. If a multirate PPM was preprovisioned, this

procedure is unnecessary.

2. NTP-E151 Provision an Optical Line Rate, page 11-3—Complete this procedure to provision the

optical line rate on a multirate PPM for the ASAP card. Single-rate PPMs do not need to be

provisioned.

3. NTP-E150 Change the Optical Line Rate, page 11-4—As needed, complete this procedure to edit

optical line rates for multirate PPMs on the ASAP card.

4. NTP-E149 Delete Pluggable Port Modules, page 11-5—As needed, complete this procedure to

delete PPMs for the ASAP card.

5. NTP-E66 Modify Line and Status Thresholds for Optical Ports, page 11-6—As needed, complete

this procedure to change line (drop) and threshold settings for all OC-N cards.

6. NTP-E105 Change an Optical Port to SDH, page 11-12—As needed, complete this procedure to

change an optical port from SONET to SDH.

7. NTP-E125 Change Card Service State, page 11-13—As needed, complete this procedure to change

card service state.

11-2

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E157 Provision a Multirate PPM

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 In node view, double-click the ASAP card where you want to provision PPM settings.

Step 4 Click the Provisioning > Pluggable Port Modules tabs.

Step 5 In the Pluggable Port Modules pane, click Create. The Create PPM dialog box appears.

Step 6 In the Create PPM dialog box, complete the following:

•PPM—Click the slot number where the SFP is installed from the drop-down list.

•PPM Type—Click the number of ports supported by your SFP from the drop-down list. If only one

port is supported, PPM (1 port) is the only menu option.

Step 7 Click OK. The newly created port appears on the Pluggable Port Modules pane. The row on the

Pluggable Port Modules pane turns light blue and the Actual Equipment Type column lists the equipment

name.

Step 8 Verify that the PPM appears in the list on the Pluggable Port Modules pane. If it does not, repeat Steps

5through 8.

Step 9 Repeat the task to provision a second PPM.

Step 10 Click OK.

Step 11 Continue with the “NTP-E151 Provision an Optical Line Rate” procedure on page 11-3 to provision the

line rate.

Stop. You have completed this procedure.

Purpose This procedure provisions a multirate pluggable port modules (PPMs) in

CTC.

Tools/Equipment None

Prerequisite Procedures NTP-E147 Install the ASAP Card, page 2-5

DLP-E211 Install the ASAP 4PIO Modules, page 18-12, as needed

DLP-E215 Install an SFP, page 18-14, as needed

Required/As Needed Required

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

11-3

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E151 Provision an Optical Line Rate

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 In node view, double-click the ASAP card where you want to provision the line rate.

Step 4 Click the Provisioning > Pluggable Port Modules tabs.

Step 5 In the Pluggable Ports pane, click Create. The Create Port dialog box appears.

Step 6 In the Create Port dialog box, complete the following:

•Port—Click the PPM number and port number from the drop-down list. The first number indicates

the PPM and the second number indicates the port number on the PPM. For example, the first PPM

with one port displays as 1-1 and the second PPM with one port displays as 2-1. When a 4PIO is

present on an ASAP card, the port is identified as 4PIO#-PPM#-Port# (for example 4-4-1). The 4PIO

number can be 1 to 4, the PPM number can be 1 to 4, but the port number is always 1.

•Port Type—Click the type of port from the drop-down list. The port type menu displays the

supported port rates on your PPM. See Table 11-1 for definitions of the supported rates on the ASAP

card.

Step 7 Click OK.

Step 8 Repeat Steps 5through 7to configure the port rates as needed.

Purpose This procedure provisions the line rate on a multirate pluggable port

module (PPM). Single-rate small-form factor pluggables (SFPs) or 4-port

I/O modules (4PIOs) do not need line rate provisioning.

Tools/Equipment None

Prerequisite Procedures NTP-E148 Preprovision an SFP Slot, page 2-8 or

NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed Required

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

Table 11-1 PPM Port Types

Card Port Type

ASAP •OC-3—155 Mbps

•OC-12—622 Mbps

•OC-48—2.48 Gbps

•ETHER—10 Gbps Ethernet

11-4

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E150 Change the Optical Line Rate

Step 9 Click OK. The row on the Pluggable Ports pane turns light blue until the actual SFP is installed and then

the row turns white.

Stop. You have completed this procedure.

NTP-E150 Change the Optical Line Rate

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 In node view, double-click the ASAP card where you want to edit the PPM port rate.

Step 4 Click the Provisioning > Pluggable Port Modules tabs.

Step 5 Click the port with the port rate you want to change in the Pluggable Ports pane. The highlight changes

to dark blue.

Step 6 Click Edit. The Edit Port Rate dialog box appears.

Step 7 In the Change To field, use the drop-down menu to select the new port rate and click OK.

Step 8 Click Yes on the Confirm Port Rate Change dialog box.

Stop. You have completed this procedure.

Purpose This procedure changes PPM port rates for the ASAP card. Perform this

procedure if you want to change the port rate on a multi-rate SFP that is

already provisioned.

Tools/Equipment None

Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

11-5

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E149 Delete Pluggable Port Modules

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network.

Step 2 Click the Alarms tab:

a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on

page 17-50 as necessary.

b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear,

resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide.

c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition

information.

Step 3 You cannot delete a port on a PPM: if it is in service, part of a protection group, has a communications

channel termination in use, is used as a timing source, has circuits, or has overhead circuits. As needed,

complete the following procedures and task:

•NTP-E61 Modify or Delete Optical 1+1 Port Protection Settings, page 10-4

•NTP-E62 Change Node Timing, page 10-4

•NTP-E128 Modify or Delete Communications Channel Terminations and Provisionable Patchcords,

page 10-7

•NTP-E52 Modify and Delete Circuits, page 9-2

•NTP-E134 Modify and Delete Overhead Circuits, page 9-3

•DLP-E115 Change the Service State for a Port, page 17-14

Step 4 In node view, double-click the ASAP card where you want to delete PPM settings.

Step 5 Click the Provisioning > Pluggable Port Modules tabs.

Step 6 To delete a PPM and the associated ports:

a. Click the PPM line that appears in the Pluggable Port Modules pane. The highlight changes to dark

blue.

b. Click Delete. The Delete PPM dialog box appears.

c. Click Yes. The PPM provisioning is removed from the Pluggable Port Modules pane and the

Pluggable Ports pane.

Step 7 Verify that the PPM provisioning is deleted:

•If the PPM was pre-provisioned, CTC shows an empty slot in CTC after it is deleted.

•If the SFP or 4PIO is physically present when you delete the PPM provisioning, CTC transitions to

the deleted state, the ports (if any) are deleted, and the PPM is represented as a gray graphic in CTC.

The SFP or 4PIO can be provisioned again in CTC, or the equipment can be removed, in which case

the removal causes the graphic to disappear.

Purpose This procedure deletes PPM provisioning for SFPs on the ASAP card.

Tools/Equipment None

Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Level Provisioning or higher

11-6

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Note If you need to remove the SFP, see the “DLP-E216 Remove an SFP” procedure on page 18-15.

If you need to remove the 4PIO, see the “DLP-E217 Remove a 4PIO Module” procedure on

page 18-16.”

Stop. You have completed this procedure.

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 at the node where you want to change the

settings. If you are already logged in, continue with Step 2.

Step 2 Complete the “NTP-E69 Back Up the Database” procedure on page 14-4.

Step 3 On the shelf graphic, double-click the OC-N card that you want to provision. The card view appears.

Step 4 Click the Provisioning > Line tabs. (Click Provisioning > Optical > Line tabs for the ASAP card).

Step 5 As needed, provision the options in Table 11-2 for each OC-N port.

Purpose This procedure changes line settings (line type, coding, and length), line

status (in service or out of service), and performance monitoring thresholds

for OC-48, OC-192 cards, and OC-N ports on ASAP cards.

Tools/Equipment None

Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2

Required/As Needed As needed

Onsite/Remote Onsite or remote

Security Provisioning or higher

Table 11-2 OC-N Card Line Settings

Heading Description Options

Port # Identifies the port number •For an OC-48 card: 1 – 16

•For an OC-192 card: 1 – 4

•For an ASAP card: up to 16 ports,

denoted by 4PIO module followed by

port number. (Example: 1-3-1

denotes the third port on 4PIO

Module 1.)

Port Name Provides the ability to assign the

specified port a name

User-defined; name can be up to 32

alphanumeric/special characters (blank

by default)

SF BER Sets the signal fail bit error rate •1E-3

•1E-4 (default)

•1E-5

11-7

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E66 Modify Line and Status Thresholds for Optical Ports

SD BER Sets the signal degrade bit error rate •1E-5

•1E-6

•1E-7 (default)

•1E-8

•1E-9

Provides Sync Indicates that the port has been

provisioned as a network element timing

reference on another node (ONS 15600,

ONS 15454, or ONS 15327)

Read-only

•Yes (checked)

•No (unchecked)

Send Do Not

Use

When checked, sends a DUS (do not use)

message on the S1 byte

•Yes (checked)

•No (unchecked; default)

BLSR Ext.

Byte

Chosen extended byte carries information

that governs BLSR protection switches.

•K3

•Z2

•E2

•F1

Admin State Sets the port service state unless network

conditions prevent the change.

•IS—Puts the port in-service. The

port service state changes to IS-NR.

•IS,AINS (default)—Puts the port in

automatic in-service. The port

service state changes to

OOS-AU,AINS.

•OOS,DSBLD—Removes the port

from service and disables it. The port

service state changes to

OOS-MA,DSBLD.

•OOS,MT—Removes the port from

service for maintenance. The port

service state changes to

OOS-MA,MT.

AINS Soak Sets the automatic in-service soak period. Duration of valid input signal, in hh.mm

format, after which the card becomes in

service (IS) automatically (0 to 48 hours,

in 15-minute increments).

Type Defines the port as SONET or SDH.

Enable Sync Msg and Send Do Not Use

must be disabled before the port can be

set to SDH.

•SONET (default)

•SDH

Table 11-2 OC-N Card Line Settings (continued)

Heading Description Options

11-8

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Step 6 Click Apply.

Service State Identifies the autonomously generated

state that gives the overall condition of

the port. Service states appear in the

format: Primary State-Primary State

Qualifier, Secondary State.

•IS-NR—(In-Service and Normal)

The port is fully operational and

performing as provisioned.

•OOS-AU,AINS—(Out-Of-Service

and Autonomous, Automatic

In-Service) The port is

out-of-service, but traffic is carried.

Alarm reporting is suppressed. The

ONS node monitors the ports for an

error-free signal. After an error-free

signal is detected, the port stays in

OOS-AU,AINS state for the duration

of the soak period. After the soak

period ends, the port service state

changes to IS-NR.

•OOS-MA,DSBLD—(Out-of-Service

and Management, Disabled) The port

is out-of-service and unable to carry

traffic.

•OOS-MA,MT—(Out-of-Service and

Management, Maintenance) The port

is out-of-service for maintenance.

Alarm reporting is suppressed, but

traffic is carried and loopbacks are

allowed.

SyncStatusMsg Allows you to view the incoming

synchronization status message by

clicking Show.

•PRS (Primary reference source –

Stratum 1)

•STU (Sync traceability unknown)

•ST2 (Stratum 2)

•ST3 (Stratum 3)

•ST3E (Stratum 3E)

•SMC (SONET minimum clock)

•ST4 (Stratum 4)

•TNC (Transit node clock)

•DUS (Do not use for timing

synchronization)

•RES (Reserved; quality level set by

user)

Enable Sync

Messages

Enables synchronization status messages

(S1 byte), which allow the node to choose

the best timing source

•Yes (checked, default)

•No (unchecked)

Table 11-2 OC-N Card Line Settings (continued)

Heading Description Options

11-9

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Step 7 Click the Thresholds subtab. The default selection is Near End, 15 Min, and Line (Figure 11-1).

Figure 11-1 Provisioning Thresholds for the OC-48 Card

Step 8 As needed, complete the following:

a. Click Line, Section, Path, or Physical to provision the line, section, path, and physical options in

Table 11-3 for each OC-N port.

b. Change the selection to Near End/Far End, 15 Min/1Day as necessary.

c. Click Refresh to view or modify the thresholds for each selection.

11-10

Cisco ONS 15600 Procedure Guide, R5.0

February 2008

Chapter 11 Change Card Settings

NTP-E66 Modify Line and Status Thresholds for Optical Ports

Table 11-3 OC-N Threshold Options (Line, Section, and Path)

Heading Description Options

Port Port number 1 – 16 for an OC-48 card, 1 – 4 for an

OC-192 card

CV Coding violations Numeric. Defaults (15 min/1 day):

Line

•21260/212600 (OC-48 Near and Far

End)

•85040/850400 (OC-192 Near and Far

End)

Section

•10000/100000 (Near End); 0/0 (Far

End)

•10000/500 (OC-192 Near and Far

End)

Path

•15/125 (OC-48/OC-192 Near and Far

End)

ES Errored seconds Numeric. Default (15 min/1 day):

Line

•87/864 (Near and Far End)

Section

•500/5000 (Near End); 0/0 (Far End)

Path

•12/100 (OC-48/OC-192 Near and Far

End)

SES Severely errored seconds Numeric. Defaults (15 min/1 day):

Line

•1/4 (Near and Far End)

Section

•500/5000 (Near End); 0/0 (Far End)

Path

•3/7 (OC-48/OC-192 Near and Far

End)

SEFS Severely errored framing seconds Numeric. Defaults (15 min/1 day):

Section

•500/5000 (Near End); 0/0 (Far End)

This manual suits for next models

Table of contents

Other Cisco Network Hardware manuals

Cisco

Cisco UCS 6248 UP User manual

Cisco

Cisco WBPN User manual

Cisco

Cisco IAD2430 Series Manual

Cisco

Cisco CATALYST 6000 Installation and operation manual

Cisco

Cisco Physical Access 1125 Appliance User manual

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... User manual

Cisco

Cisco ISA550 Instruction Manual

Cisco

Cisco IAD1101 User manual

Cisco

Cisco 2600 Series Technical document

Cisco

Cisco Engine 611 User manual

Cisco

Cisco MultiRIP Ethernet Card User manual

Cisco

Cisco 220 Series Smart Plus User manual

Cisco

Cisco Firepower 4100 Series User manual

Cisco

Cisco Firepower 1010 User manual

Cisco

Cisco ONS 15454 SDH E1-75 User manual

Cisco

Cisco NCS 1004 User manual

Cisco

Cisco Nexus 93600CD-GX Manual

Cisco

Cisco Catalyst 8300 Series Manual

Cisco

Cisco ONS 15327 Operator's manual

Cisco

Cisco GS7000 Operating instructions

Cisco

Cisco SCE 1000 and Operator's manual

Cisco

Cisco Aironet 340 Series User manual

Cisco

Cisco IPS-4260-K9 - IPS Sensor 4260 User manual

Cisco

Cisco CSC-C2FCIT Instruction Manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide