Cisco Physical Access Gateway User manual

QUICK START GUIDE

Cisco Physical Access Gateway Quick Start Guide

1Summary Steps

2Cisco Physical Access Gateway

3Wall Mounting a Gateway or Optional Module

4Cisco Physical Access Reader Module

5Cisco Physical Access Output Module

6Cisco Physical Access Input Module

7Obtaining Documentation and Submitting a Service Request

278-18554-05

1 Summary Steps

The following steps are an example of the main installation and configuration tasks for a Cisco Physical Access Control system.

The exact procedures and order of installation for your system may vary.

Tip To ensure proper operation, perform a test installation of all equipment on a lab bench before actual installation: use

Cisco PAM to configure the Gateways and all peripheral devices including locks, readers, and sensors. This allows any

issues to be resolved before the equipment is installed at the various access points.

1. Unpack and mount the Cisco Physical Access Gateway.

2. Unpack and mount optional reader, input or output modules, if necessary.

3. Connect door readers, input and output devices to the Cisco Physical Access Gateway or optional modules.

4. Connect power to the Cisco Physical Access Gateway and any optional modules.

5. Connect an Ethernet cable from a PC to the ETH1 interface on the Gateway module.

Note To enter the Gateway initial configuration, be sure to connect your PC to the ETH1 port. The ETH0 port is used

for network communication.

6. Open a web browser on your PC and enter https://192.168.1.42. This URL opens the web-based configuration page.

7. Enter the default username and password:

default username: gwadmin

default password: gwadmin

Enter the Network settings, as shown in Figure 1.

Figure 1 Network Settings for the Cisco Physical Access Gateway

8. Enter the ETH0 Configuration settings. The ETH0 port is used for network communications with the Cisco PAM appliance.

a. If a Dynamic Host Configuration Protocol (DHCP) server is configured on your IP network, select the DHCP check

box for ETH0 to automatically configure the required IP network settings, including IP address, Subnet Mask, and

Gateway. The DHCP check box is selected by default.

b. (Optional) If a DHCP server is not used to assign IP address settings, enter the following information in the ETH0 fields:

–

IP address: Enter the IP address of the Cisco Physical Access Gateway.

–

Subnet Mask: Enter the subnet mask.

–

Gateway: Enter the IP gateway address.

9. (Optional) Enter the DNS Server address if names (not IP addresses) are used for the CPAM address.

10. Enter the Cisco PAM Configuration:

a. Enter the Cisco PAM IP address (IP address or name) to enable Gateway communication with the appliance.

b. Enter the port number for the Cisco PAM appliance. The port number must be greater than 1024 and less 65535. The

default is 8020.

Tip DHCP can also be configured to supply the Gateway with the IP address of the Cisco PAM appliance by configuring

option 150 in the DHCP response. The Cisco PAM appliance TCP port number can be provided by DHCP option 151

of the DHCP response.

c. Enable SSL: The secure socket layer (SSL) is enabled for secure communication between the Gateway and Cisco PAM

appliance by default. If necessary SSL can be disabled by deselecting the Enable SSL check box.

Note SSL is enabled or disabled for all Gateways and the Cisco PAM appliance. Cisco Systems recommends that SSL

always be enabled to ensure secure communications. If the SSL settings are changed, you must reset all

Gateways and the Cisco PAM appliance.

11. Click Save to save the settings. Wait until the Gateway resets and the web browser displays the screen Network Settings

Applied. Changes do not take effect until saved.

12. Repeat these steps for each Gateway in the system.

13. Perform additional configuration, verification, and monitoring tasks as described in the Cisco Physical Access Manager User

Guide.

Tip For complete instructions, see the Cisco Physical Access Gateway User Guide.

478-18554-05

2 Cisco Physical Access Gateway

Package Contents

Each Cisco Physical Access Gateway includes the following:

•Six resistors (1K) for supervised input interfaces

•Two mounting brackets, with 4 screws for each bracket

•Regulatory compliance and safety information

•Quick Start guide

•Connector plugs, including the following:

Gateway Module Overview and Port Descriptions

The Cisco Physical Access Gateway includes connections for power, Ethernet, door readers and other input and output devices,

as shown in Figure 2.

Figure 2 Cisco Physical Access Gateway Ports and Connectors: Side View

Note For detailed installation and configuration instructions, see the Cisco Physical Access Gateway User Guide.

Type Quantity

10 Pin 1

3 Pin 4

2 Pin 6

187040

The following items are shown in Figure 2:

Type Description

1Power Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC

external power source.

2CAN A three-wire CAN bus is used to connect additional modules, including the Cisco Reader

Module, Cisco Input Module, and Cisco Output Module.

Note Modules are connected using the CAN1 interface. The CAN2 interface is not

supported in this release.

3SVR (Server) When the LED is steady green, the Gateway is connected to a Cisco PAM.

4Fast Ethernet

interfaces

There are two 10/100 BASE-TX RJ-45 connectors:

•ETH 0: connects the Gateway to the network. ETH 0 also supports Power over Ethernet

(PoE) for the device (optional).

•ETH 1: connects the device to a PC to access the device configuration web page.

5Serial interface The RS-485 interface is not supported in this release.

6Wiegand interface This interface can be configured as the following:

•One 10-pin Wiegand/clock and data reader interface to connect a single door reader.

•Two 5-pin Wiegand/clock and data interfaces to connect two door readers (for

installations where a 5-pin interface is sufficient).

Note Disconnect power from the Gateway or Reader module before connecting reader

devices to the modules. Connecting a reader device when the modules are powered

can cause the Gateway or Reader module to malfunction.

7Input interfaces Three input interfaces used to sense the contact closure. Each input can be configured as

supervised or unsupervised and can be configured to sense a Normally Open (NO) or

Normally Closed (NC) contact.

•An unsupervised input senses a simple contact closure state, including Normal or Alarm.

When connected to open contacts, the terminal voltage range is 4V to 5V. For closed

contacts, the voltage range is 0V to 0.7V.

•A supervised input senses four contact states, including Normal, Alarm, Open and Short.

These inputs require 1K End-Of-Line (EOL) termination resistors installed at the

contacts (two resistors are included in the accessory kits for each Input port). Refer to

the Cisco Physical Access Gateway User Guide for instructions to install the termination

resistors.

678-18554-05

8Output interfaces Three Form C (5A @ 30V) relay output interfaces. Each output connection can be configured

as either Normally Closed (NC) or Normally Open (NO).

•C & NO connection: The relay is normally open. The circuit is closed when triggered.

•C & NC connection: The relay is normally closed. The circuit is opened when triggered.

Notes:

•Install surge protection between the output device and the Cisco PAM module. See the

Cisco Physical Access Gateway User Guide for instructions.

•Common (C) is always used, and either NC or NO is used to complete the connection.

•All Generic Output devices installed in Cisco PAM systems prior to Release 1.1.0 were

connected to the Gateway, Reader, or Output modules with the wiring reversed. If

upgrading to Cisco PAM Release 1.1.0 or later from an earlier release, disconnect all

Generic Output devices and do the following:

–

Connect Normally Open devices to the N.O. and C connectors on the Gateway,

Reader, or Output module.

–

Connect Normally Closed devices to the N.C. and C connectors on the Gateway,

Reader, or Output module.

9PF Power fail input: an unsupervised input that raises a “power fail” alarm when the circuit is

open. Can be configured as an additional unsupervised port. An unsupervised input indicates

only normal or alarm. The corresponding LED is red when circuit is open (when no input is

connected).

10 TM Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open.

Can be configured as an additional unsupervised port. An unsupervised input indicates only

normal or alarm. The corresponding LED is red when circuit is open (when no input is

connected).

11 Reset Resets the device. See “Resetting the Cisco Physical Access Gateway” in the Cisco Physical

Access Gateway User Guide for more information.

Type Description

3 Wall Mounting a Gateway or Optional Module

Each Cisco Physical Access Gateway and optional module includes two mounting brackets and four screws to mount the

gateway to the wall. Figure 3 shows the three options for attaching the included wall-mount brackets to a module.

Figure 3 Three Options for Installing Wall Mount Brackets

The following items are shown in Figure 3:

Wall Mount Installation Kit Contents

Each module includes a wall mount installation kit that contains the following:

1Option 1: Bottom end mounting 4Mounting Brackets (included)

2Option 2: Bottom side mounting 5Screws

3Option 3: Side mounting

Hardware Item Quantity

Wall Mount brackets 2

Screws 8

187050

878-18554-05

4 Cisco Physical Access Reader Module

What’s In the Box

Each Cisco Reader Module includes the following:

•Six resistors (1K) for supervised input interfaces

•Two mounting brackets, with 4 screws for each bracket

•Regulatory compliance and safety information

•Quick start guide

•Connector plugs, including the following:

Installing the Module

See Wall Mounting a Gateway or Optional Module, page 7.

Reader Module Overview and Port Descriptions

The Cisco Reader Module includes ports for connecting up to two doors and associated input and output devices, as shown in

Figure 4.

Figure 4 Cisco Reader Module Ports and Connectors

Type Quantity

10 Pin 1

3 Pin 4

2 Pin 6

187049

The following items are shown in Figure 4:

Type Description

1Power Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC

external power source.

2CAN interfaces A 3-wire CAN bus is used to connect additional modules.

Note Modules are connected using the CAN1 interface. The CAN2 interface is not

supported in this release.

3CAN terminator The CAN terminator switch should be set to ON for the last device in a CAN wiring bus.

This switch should be set to OFF for all other devices in the CAN bus.

4Serial Interface The RS-485 interface is not supported in this release.

5Wiegand interface This interface can be configured as the following:

•One 10-pin Wiegand/clock and data reader interface to connect a single door reader.

•Two 5-pin Wiegand/clock and data interfaces to connect two door readers (for

installations where a 5-pin interface is sufficient).

Note Disconnect power from the Gateway or Reader module before connecting reader

devices to the modules. Connecting a reader device when the modules are powered

can cause the Gateway or Reader module to malfunction.

6Input interfaces Three input interfaces used to sense the contact closure. Each input can be configured as

supervised or unsupervised and can be configured to sense a Normally Open (NO) or

Normally Closed (NC) contact.

•An unsupervised input senses a simple contact closure state, including Normal or Alarm.

When connected to open contacts, the terminal voltage range is 4V to 5V. For closed

contacts, the voltage range is 0V to 0.7V.

•A supervised input senses four contact states, including Normal, Alarm, Open and Short.

These inputs require 1K End-Of-Line (EOL) termination resistors installed at the

contacts (two resistors are included in the accessory kits for each Input port). Refer to

the Cisco Physical Access Gateway User Guide for instructions to install the termination

resistors.

10 78-18554-05

7Output interfaces Three Form C (5A @ 30V) relay output interfaces. Each output connection can be configured

as either Normally Closed (NC) or Normally Open (NO).

•C & NO connection: The relay is normally open. The circuit is closed when triggered.

•C & NC connection: The relay is normally closed. The circuit is opened when triggered.

Notes:

•Install surge protection between the output device and the Cisco PAM module. See the

Cisco Physical Access Gateway User Guide for instructions.

•Common (C) is always used, and either NC or NO is used to complete the connection.

•All Generic Output devices installed in Cisco PAM systems prior to Release 1.1.0 were

connected to the Gateway, Reader, or Output modules with the wiring reversed. If

upgrading to Cisco PAM Release 1.1.0 or later from an earlier release, disconnect all

Generic Output devices and do the following:

–

Connect Normally Open devices to the N.O. and C connectors on the Gateway,

Reader, or Output module.

–

Connect Normally Closed devices to the N.C. and C connectors on the Gateway,

Reader, or Output module.

8PF Power fail input: an unsupervised input that raises a “power fail” alarm when the circuit is

open. Can be configured as an additional unsupervised port. An unsupervised input indicates

only normal or alarm. The corresponding LED is red when circuit is open (when no input is

connected).

9TM Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open.

Can be configured as an additional unsupervised port. An unsupervised input indicates only

normal or alarm. The corresponding LED is red when circuit is open (when no input is

connected).

Type Description

This manual suits for next models

Table of contents

Other Cisco Gateway manuals

Cisco

Cisco Explorer 4250 User manual

Cisco

Cisco DPC3941T User manual

Cisco

Cisco DPQ2425 User manual

Cisco

Cisco TelePresence ISDN GW MSE 8321 User manual

Cisco

Cisco Expressway Series User manual

Cisco

Cisco Linksys WAG310G User manual

Cisco

Cisco RF 1 User manual

Cisco

Cisco EPC3928 DOCSIS User manual

Cisco

Cisco Linksys WAG325N User manual

Cisco

Cisco EPC2434 User manual

Cisco

Cisco Linksys SPA8000-XU Original operating instructions

Cisco

Cisco EPC3925 User manual

Cisco

Cisco VG310 Instruction Manual

Cisco

Cisco ASR 9000 Series Installation manual

Cisco

Cisco RFGW-10 Manual

Cisco

Cisco IC3000 Manual

Cisco

Cisco ASR 5000 Series Instruction Manual

Cisco

Cisco DPC3848 User manual

Cisco

Cisco LINKSYS RFC 2364 Original operating instructions

Cisco

Cisco DPC2434 User manual

Cisco

Cisco IG21 Series User manual

Cisco

Cisco VG224 - Analog Phone Gateway User manual

Cisco

Cisco ASR 5000 Instruction Manual

Cisco

Cisco DPC User manual

Popular Gateway manuals by other brands

LST

LST M500RFE-AS Specification sheet

Kinnex

Kinnex Media Gateway quick start guide

2N Telekomunikace

2N Telekomunikace 2N StarGate user manual

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Original instructions

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE user guide

Telsey

Telsey CPVA 500 - SIP Technical manual

RTA

RTA 460A-NNA4 Product user guide

Shaw

Shaw Gateway HDPVR user manual

ABB

ABB VSN900 Commissioning manual

Commander

Commander Pulse owner's manual

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E manual

NETGEAR

NETGEAR C6300BD installation guide

Amit

Amit CDW531AM user guide

HMS

HMS Netbiter EasyConnect EC150 user manual

Huawei

Huawei EchoLife HG620 user guide

AT&T

AT&T U-verse 3801 Replacement self-installation guide

Logic IO

Logic IO RTCU MX2 turbo Technical manual

Suttle

Suttle MediaMAX MXM-521 installation instructions