Bosch TC2073 User manual

Instruction Manual

EN Indoor Wall and

Corner Housings

TC2073

EN |2

Bosch Security Systems | 09 August 2004

TC2073 | Instruction Manual | Important Safeguards

Important Safeguards

1. Read, Follow, and Retain Instructions - All safety

and operating instructions should be read and

followed before operating the unit. Retain instructions

for future reference.

2. Heed Warnings - Adhere to all warnings on the unit

and in the operating instructions.

3. Electrical Connections - Only a qualified electrician

should make electrical connections.

4. Cable Runs - All cable runs must be within

permissible distances.

5. Mounting - This unit must be properly and securely

mounted to a supporting structure capable of

sustaining the weight of the unit. Accordingly:

a. The installation should be made by a qualified

installer, in compliance with local codes.

b.Exercise care in selecting suitable hardware to

install the unit, taking into account both the

composition of the mounting surface and the

weight of the unit. Periodically examine the unit

and the supporting structure to ensure that the

integrity of the installation is intact.

Failure to comply with these stipulations may result in

separation from the support structure. This may cause

damages or injury to anyone or anything struck by the

falling unit.

6. Attachments - Attachments not recommended by

the product manufacturer should not be used, as they

may cause hazards.

Safety Precautions

Attention: Installation should be performed by

qualified service personnel only in accordance

with the National Electrical Code or applicable

local codes.

Power Disconnect. Units with or without

ON-OFF switches have power supplied to the

unit whenever the power cord is inserted into the

power source; however, the unit is operational

only when the ON-OFF switch is in the ON

position. The power cord is the main power

disconnect for all units.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

This symbol indicates the presence of

uninsulated “dangerous voltage” within the

product’s enclosure. This may constitute a

risk of electric shock.

The user should consult the operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

EN |3

Bosch Security Systems | 09 August 2004

TC2073 Series | Instruction Manual | Unpacking

1UNPACKING

This mechanical equipment should be unpacked and

handled carefully.

Check for the following items:

Qty. Item

1Model No. of unit

1Key (taped to the housing cover)

1Corner-mount housing

1Camera bracket

1Toolhead driver1for security fastener

1One tool per housing

If an item appears to have been damaged in shipment,

replace it properly in its carton and notify the shipper.

If any items are missing, notify your Bosch Security

Systems Inc. Sales Representative or Customer Service.

The shipping carton is the safest container in which the

unit may be transported. Save it for possible future use.

2SERVICE

If the unit ever needs repair service, the customer

should contact the nearest Bosch Security Systems, Inc.

Service Center for return authorization and shipping

instructions.

Service Centers

USA

Phone: 800-366-2283 or 717-735-6638

fax: 800-366-1329 or 717-735-6639

CCTV Spare Parts

Phone: 800-894-5215 or 408-956-3853 or 3854

fax: 408-957-3198

e-mail: [email protected].com

Canada

Phone: 514-738-2434

Europe, Middle East & Asia Pacific Region

Phone: 32-1-440-0711

For additional information, see

www.boschsecuritysystems.com.

3INSTALLATION

1. Remove the contents from the box.

2. Loosen the security fasteners using the toolhead

driver, and open the front half of the housing.

3. Remove the paper from the back side of the

window.

4. The Camera bracket can be mounted into the

housing in one of two ways, depending on camera

size and the desired angle (see FIGURE 1).

5. Place the housing in the corner and mark the

location of the four (4) mounting holes.

6. Pass the electrical and video cables through the

hole provided in the back of the housing.

7. Mount the housing by bolting it to the wall.

8. Make the electrical and camera connections.

USE 0NLY CLASS 2 POWER SUPPLY FOR

THE CAMERA.

9. Adjust the camera angle and tighten the camera

bracket. Loosen, but do not remove the nuts to

adjust the bracket.

10. Close the housing and tighten the security

fasteners.

FIGURE 1

3935 890 15912 04-33 | Updated August 09, 2004 | Data subject to change without notice.

Bosch Security Systems, Inc.

850 Greenfield Road

Lancaster, PA 17601 USA

Tel: 800-326-3270

Fax: 1-717-735-6560

www.boschsecuritysystems.com

Bosch Security Systems B.V.

P.O. Box 80002

5600 JB Eindhoven

The Netherlands

Tele +31 40 27 80000

Bosch Security Systems Pte Ltd.

38C Jalan Pemimpin

Singapore 577180

Republic of Singapore

Tel: 65 (6) 319 3486

Table of contents

Other Bosch Security System manuals

Bosch

Bosch DS7400XiV4-EXP User manual

Bosch

Bosch AMAX panel 4000 User manual

Bosch

Bosch Praesideo User manual

Bosch

Bosch Fire System User manual

Bosch

Bosch D623 Series User manual

Bosch

Bosch DIP-6083-8HD User manual

Bosch

Bosch D222 User manual

Bosch

Bosch Solution 16i User manual

Bosch

Bosch UNPXF Series User manual

Bosch

Bosch PAVIRO Mounting instructions

Bosch

Bosch LTC 8016/90 User manual

Bosch

Bosch Spexor User manual

Bosch

Bosch FMC-210-DM-G-R User manual

Bosch

Bosch ITS-SPDIAL-FR User manual

Bosch

Bosch CM705B How to use

Bosch

Bosch HSG9483 Series User manual

Bosch

Bosch ISN-SM-30 User guide

Bosch

Bosch Security Systems User manual

Bosch

Bosch Solution 144 User manual

Bosch

Bosch SOLUTION 3000 User manual

Bosch

Bosch MAP 5000 User manual

Bosch

Bosch Security Systems User manual

Bosch

Bosch Radion Specialty RFBT User manual

Bosch

Bosch MIC IP starlight 7000i User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual