Bosch 715ES Reference manual

Models: 715ES, C800ES, C920ES, C920ESC, 2400ES, 2700ES

Replacing gas valve

Service Bulletin G3-28

Introduction

This procedure must be performed by a licensed gas technician

with a calibrated combustion gas analyzer.

 The gas valve is not gas type specic but requires different CO₂

values when calibrating for different gas types.

Tools needed:

Phillips head screwdriver

 Small at head screwdriver

#40 Torx driver

 Combustion gas analyzer

30mm open end wrench or large adjustable wrench

4mm allen wrench

Preparation

1. Unplug water heater and turn off gas to heater using installer

supplied manual shut off valve.

2. Loosen two Phillips head screws located at bottom rear of cover.

(Fig. 1, step 1, pos. 1).

3. Lift front cover upward and remove. (Fig. 1, step 1, pos. 2 & 3)

Step 1 Step 2

tep

Figure 1

4. Remove combustion cover by unclipping two upper and two

lower clips securing cover. (Fig. 1, step 2)

5. Remove 3 Phillips screws on control unit (Fig. 2, step 1). Place

control unit into the service postion by engaging its tabs with

the holes in the horizontal sheet metal on bottom of the heater

chassis . (Fig. 2, step 2).

Step 2

Step 1

tep

Step

Figure 2

Gas

Valve

Removing the gas valve

1. Unplug wire connection from gas valve. (Fig. 3, pos. 1).

2. Disconnect clear silicone pressure balance tube from right side

of gas valve. (Fig. 3, pos. 2)

3. Loosen and disconnect large 30mm hex nut on the left side of

gas valve. (Fig. 3, pos. 3).

4. Unscrew the three 4mm allen screws from the top of the gas

valve. (Fig. 3, pos. 4).

5. Remove gas valve from the water heater.

http://waterheatertimer.org/Troubleshoot-Bosch-Tankless-water-heaters.html

Data subject to change without notice | Printed in the USA | BTC 710002312 A | 01.2009 Bosch Thermotechnology Corp.

Service bulletin

18 | G3-28 | 715ES, C800ES, C920ES, C920ESC, 2400ES, 2700ES

Bosch Thermotechnology Corp.

50 Wentworth Avenue

Londonderry, NH 03053

Tel: 1-866-642-3198

Fax: 1-603-584-1681

www.boschhotwater.com

Figure 3

Installing gas valve

1. Replace both the grey ber washer on the left side of the gas

valve and the rubber gasket on the top of the gas valve.

2. Hold replacement gas valve in place and reinstall the three allen

screws into the top of the gas valve. (Fig. 3, pos. 4).

3. Reinstall 30mm hex nut on the left side of gas valve.

(Fig. 3, pos. 3)

4. Open manual gas shutoff valve and check for leaks at all connec-

tions.

5. Reinstall silicone pressure balance tube to right side of gas

valve. (Fig. 3, pos. 2).

6. Reconnect wire connection to gas valve. (Fig. 3, pos. 1).

Calibrating gas valve

1. Reinstall combustion cover. (Fig. 1, step 2).

2. Return control unit to normal position and secure with 3 Phillips

head screws. (Fig. 2)

3. Plug in water heater and push power button to the "ON" posi-

tion.

4. Open a hot water tap. If heater res, adjust CO₂ using service

bulletin G3-12 Measuring and adjusting CO₂.

5. If the heater does not fire, allow the unit to display the EA error

code and shut off hot water tap. The fan will continue to run to

purge the heater of gasses. Continue to the next section for a

rough gas valve adjustment.

Rough gas valve adjustment

Note: Do not forcefully tighten adjustment screws past bottom out

point. Stop bottoming out screw when resistance is felt. Failure

to do so will damage the gas valve.

1. Locate adjustment screw on gas valve. Loosen Phillips head

screw so retaining cover can be rotated to expose brass slotted

screw. (Fig. 4, pos. 1 & 2).

2. Turn brass slotted screw clockwise gently until it bottoms out

and/or screw resistance increases. (Fig. 4, pos. 3).

Figure 4

3. Once the slotted screw is bottomed out, make the following

adjustment to the slotted screw depending on your model and

gas type. (Fig. 4, pos. 3)

For models GWH 715 ES/GWH 2700 ES/ GWH 2400 ES:

Natural Gas: 2.5 turns counter-clockwise on brass slotted screw

Liquid Propane: .75 turns counter-clockwise on brass slotted screw

For model GWH C 800 ES:

Natural Gas: 3 turns counter-clockwise on brass slotted screw

Liquid Propane: 1 turn counter-clockwise on brass slotted screw

For models GWH C920 ES/GWH C 920 ESC:

Natural Gas: 2.5 turns counter-clockwise on brass slotted screw

Liquid Propane: Leave brass slotted screw bottomed out

4. Open a hot water tap. If heater res, adjust CO₂ using service

bulletin G3-12 Measuring and adjusting CO₂. If heater still does

not re, contact Bosch Thermotechnology Corp.

5. Reinstall brass slotted screw cover and secure with Phillips

screw. (Fig. 4, pos. 1 & 2).

!WARNING

FAILURE TO PROPERLY CALIBRATE THE

HEATER’S CO₂ LEVEL MAY RESULT IN A

HAZARDOUS CONDITION CAUSING

SEVERE PERSONAL INJURY OR DEATH.

Other manuals for 715ES

This manual suits for next models

Other Bosch Control Unit manuals

Bosch

Bosch ICP-COM-IF User manual

Bosch

Bosch Heatronic 4000 Instructions for use

Bosch

Bosch FLM-420-RLV1-E User manual

Bosch

Bosch PAVIRO PVA-1WEOL Installation and operation manual

Bosch

Bosch KTS Truck User manual

Bosch

Bosch Rexroth PSI 6500 Series Manual

Bosch

Bosch ETT 223 User manual

Bosch

Bosch DCU 220 Setup guide

Bosch

Bosch K20 RF User manual

Bosch

Bosch Rexroth VM350 User manual

Bosch

Bosch Rexroth H-4WEH...XE Series User manual

Bosch

Bosch AMC2-4WE User manual

Bosch

Bosch MS 50.4 User manual

Bosch

Bosch FM441/CMM 910 User manual

Bosch

Bosch Rexroth IndraControl XFE 01.1 Series User manual

Bosch

Bosch DCU 220 Setup guide

Bosch

Bosch C-IR 20 User manual

Bosch

Bosch Conettix B444-A User manual

Bosch

Bosch Rexroth 3DREP 6 XE Series User manual

Bosch

Bosch B426 Owner's manual

Bosch

Bosch Rexroth BVD 52 Series User manual

Bosch

Bosch B443 User manual

Bosch

Bosch rexroth PSK Gen 2 User manual

Bosch

Bosch Control 8310 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual