Blade BM5000S User manual

Safety Precaution

CAUTION:

The lightning flash with

arrowhead symbol, within an

equilateral triangle, is intended

to alert the user to "dangerous

voltage" and to prevent from a

risk of electric shock.

Warning:

To reduce the risk of electric

shock, don't open the cabinet.

Refer servicing to qualified

personnel only.

The exclamation point within an

equilateral triangle is intended to

alert the user to important

operating and maintenance

(servicing).

WARNING: Do not use this STB where contact with / or immersion in water is a possibility. Do not use

near flower vases, washbowls, kitchen sinks, laundry tubs, swimming pools, etc.

WARNING: Do not put near naked flame; otherwise there is the danger of fire.

WARNING: The unit should be connected to a power supply only of the type described in the operating

instructions or as marked on the unit. If you are not sure of the type of power supply (for example, 120

or 230 V) to your home, consult your local dealer or local power company.

WARNING: This product installs diodes. Do not open the cabinet or touch any parts in the inner

mechanism. Consult your local dealer for technical service if the opening is required.

Note: To ensure proper use of this product, please read this User manual carefully and retain

for further reference.

Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and remote control

with a soft cloth lightly moistened with a mild detergent solution.

Attachments: Never add any attachments and/or equipment without the manufacturer consent; as

such additions may result in the risk of fire, electric shock, or other personal injury.

Locating: Slots and openings in the cabinet are provided for ventilation to protect it from overheating.

Do not block these openings or allow them to be blocked by placing the STB on a bed, sofa, or other

similar surface, nor should it be placed over a radiator or heat register.

Power-Cord Protection: Place the power-supply cord out of the way, where it will not be walked on.

Please pay special attention to cords at plugs, convenience receptacles, and the point where they exit

from the unit.

Object and Liquid Entry: Never put objects of any kind into this STB through openings, as they may

touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill

any liquid on the STB.

Note: Moisture may be formed on internal items In the following conditions:

¾When the unit is suddenly moved from cold environment or an air-condition room to a warm place.

¾Immediately after a heater has been turned on.

¾In a steamy or very humid room.

If the moisture forms inside the unit, it may not operate properly. To correct this problem, turn on the

power and wait about two hours for the moisture to evaporate.

Parts Replacement: When the unit parts need to be replaced, user should make sure the service

technician use the replacement parts specified by the manufacturer or having the same characteristics

as the original part. Unauthorized replacement may put the unit In the risk of fire, electric shock or other

hazards.

Safety Check: After all the maintenances and repairs are done, user is required to request the service

technician to conduct the overall safety check to ensure the machine is In the proper condition.

Environment protection

ATTENTION !

Your product is marked with this symbol. It means that the used electrical and electronic products should

not be mixed with general household waste. There is a separate collection system for these products.

CONTENTS

SAFETY PRECAUTION....................................................................................1

ENVIRONMENT PROTECTION........................................................................2

1. FRONT PANEL.............................................................................................5

2. REAR PANEL................................................................................................5

3. CONNECTING YOUR SYSTEM ...................................................................6

4. REMOTE CONTROLLER .............................................................................7

5. BASIC OPERATIONS...................................................................................9

5.1 TURN ON STB.............................................................................................9

5.2 POWER.......................................................................................................9

5.3 CHANNEL UP/CHANNEL DOWN ....................................................................9

5.4 VOLUME UP/VOLUME DOWN........................................................................9

5.5 NUMBER.....................................................................................................9

5.6 MUTE .........................................................................................................9

5.7 PAUSE........................................................................................................9

5.8 RECALL ......................................................................................................9

5.9 FAVORITE...................................................................................................9

5.10 AUDIO ....................................................................................................10

5.11 INFORMATION .........................................................................................10

5.12 EPG ......................................................................................................10

5.13 TV/RADIO.............................................................................................11

5.14 CHANNEL LIST ........................................................................................11

5.15 PAGE UP/PAGE DOWN............................................................................11

5.16 TELETEXT...............................................................................................11

5.17 SUBTITLE................................................................................................12

5.18 FIND.......................................................................................................12

5.19 PIP (PICTURE IN PICTURE).......................................................................13

5.20 ZOOM.....................................................................................................15

5.21 MENU.....................................................................................................15

5.22 EXIT.......................................................................................................15

5.23 OK.........................................................................................................15

6. CHANNEL ...................................................................................................16

7. INSTALLATION...........................................................................................19

8. MULTIMEDIA ..............................................................................................23

9. SETUP.........................................................................................................27

10. OTHERS....................................................................................................34

11. SPECIFICATIONS.....................................................................................38

1. Front Panel

1. POWER KEY: To switch the receiver power on/stand by

2. MENU KEY: To open the main menu

3. CH +/-: To select the next or previous saved channel or to move cursor up/down in the menu

4. VOL+/-: To increase/decrease the volume level or move cursor left/right in the menu

5. OK KEY: Enter the selected menu or channel

6. VFD (Vacuum Florescent Display) : Indicate the channel information and the current status

7. Remote Sensor: Detects infrared signal from remote control unit

8. POWER Indicator: Lights up when the receiver is powered on

9. CA Slot: Insert a CA Card (Supports Single CA interface-ISO7816)

10. USB Port: USB 2.0, connect to USB hard disk or flash disk

2. Rear Panel

Please refer to the diagram above for all possible connections of your receiver

Do not connect the unit to the mains socket until all other connections have been made and checked.

Your configuration may vary depending on model.

1. POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.

2. INPUT (LNB IN 13/18V 500mA MAX): Connect the coaxial cable from LNB of your Dish.

3. HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.

4. RS232 SERIAL PORT: To transfer the data to another STB or PC by RS-232 cable

5. YPbPr: Analog component video output

6. VIDEO: Used to connect any external video.

7. AUDIO R/L: Used to connect any external audio amp or system.

8. OPTICAL: Digital Audio Output via Optical SPDIF Port

9. Ethernet PORT: Plug-in Ethernet Board(RJ45 Port)

10. USB Port: USB 2.0, connect to USB hard disk or flash disk

3. Connecting Your System

There are four ways to connect the receiver to your existing TV system. We recommend using one of the

following cases for the best result:

1. If you have a high definition television set, you should use a HDMI cable for best results. Plug one end

of the cable into the HDMI socket on the receiver and the other end into the matching socket on your

television. In this case, you do not have to make audio connections because the HDMI connector can

output stereo audio or Dolby digital audio.

2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to an

RCA jack on your TV.

Finally connect the coaxial cable from the LNB to the Input on the receiver.

TV with Motorized System (DiSEqC 1.2 / USALS)

Connect one end of your coaxial cable to the LNB IN connector on the receiver and the other end to the

Receiver connector on the DiSEqC 1.2 / USALS motor.

Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 / USALS motor.

All our receivers are designed to be DiSEqC 1.0 / DiSEqC 1.2 /USALS compatible.

This allows multiple antennas to be connected to the receiver at the same time.

If you have two or more fixed antennas or LNBs, we recommend you use a DiSEqC 1.0 switch. Connect

the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch. Do the

same for any other LNBs that you have.

Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch.

Connect the other end to Input on the receiver.

4. Remote Controller

1. POWER: To switch ON/OFF the receiver power supply.

2. MUTE: To mute or restore the sound

3. TV/RADIO: To switch between TV and RADIO.

4. NUMBER KEYPAD: To select TV/Radio channel and enter programming parameters by the numeric

keys and to input the character by the alphabetical keys.

5. RECALL: To return to the previously viewed channel.

6. RED, GREEN, YELLOW, BLUE KEYS: Multi-function keys in menu mode.

7. MENU: Display the main menu or return to the previous one.

8. EXIT: To exit from the menu or pop-up window or cancel the present running functions.

9. PAGE +/-: To move up the cursor to the next or previous page in the menu or channel list.

10. SUB: To show subtitle.

11. TXT: To open teletext page on the channel which has teletext information.

12. FIND: Enter into a menu to search the channel you want.

13. ZOOM: To magnify a certain area on the images

14. OK: To carry out the selection and enter into chosen menu.

15. CH Up/Dn: To turn the next or previous channel and to move the highlight bar for selecting options

to upward or downward on the menu.

16. VOL +/-: To adjusts the sound volume up or down and to move the highlight bar for selecting options

to right or left on the menu.

17. FAV: The shortcut key to favorite menu.

18. INFO: The shortcut key to the information menu.

19. EPG: The shortcut key to the EPG menu.

20. AUDIO: Selects the audio mode among Left / Right / Stereo / Mono

21. USB: The shortcut key to the USB menu.

22. FB/FF: To fast back or fast forward.

23. PLAY/PAUSE: to pause and play the file when you press play / pause key.

24. STOP: To stop the current play.

25. STEP: Jump forward by chapter.

26. RECORD: To make recording of play.

27. NEXT: To change into the next play.

28. PREV: To change into the previous play.

5. Basic Operations

5.1 Turn on STB

First, press the Power to turn on the unit.

When the STB is first used, there will play the first channel from the default Channel List. If the STB is

not first used, STB will play the same channel as last time before turning off.

5.2 Power

1. Press [Power] Key can enter the Standby state

2. In Standby state, press [Power] Key again can call back the unit and go on play the previous channel

3. User can also disconnect the device’s main power to end the Standby state.

5.3 Channel Up/Channel Down

In full screen, press [CH Up/Dn] to change channel.

5.4 Volume Up/Volume Down-

In full screen, press [Vol +/-] to adjust volume.

5.5 Number

In full screen, use number key on the Remote Control Unit to change channel.

5.6 Mute

1. Press [MUTE] key to mute the sound and the screen will show up mute OSD.

2. Press [MUTE] key again to restore sound.

5.7 Pause

By pressing [Pause] key once, the picture and sound will be paused and then, by pressing [PAUSE] key

again, you can continue to watch.

5.8 Recall

Press [RECALL] key will directly switch to the previous channel that you played before current channel.

5.9 Favorite

1. In full screen, press [FAV] key, it will display a window of “Favorite Group” on the left of the screen.

2. In the window of “Favorite”, you can move highlight by press [Ch Up/Dn] key and press [OK] key to

select favorite group.

3. You also can press [VOL +/-] keys to select different “Favorite Group”.

4. Press [Exit] key to exit the current window.

Table of contents

Other Blade Receiver manuals

Blade

Blade BM-7000s User manual

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual