Black Box COMPACT T1 User manual

Compact T1

QUICK START GUIDE

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside the U.S. call 724-746-5500)

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: info@blackbox.com

MAY 2003

PRODUCT P/N MT850A

002-0162-0001

Supporting Software Version:

Controller 6.1

IP Router 1.6

CMG Router 2.0

PREFACE

Preface

Safety Information

CAUTION! ALWAYS USE CAUTION WHEN INSTALLING TELEPHONE LINES.

READ THE CAUTIONS BELOW FOR DETAILS ON SAFETY GUIDELINES TO PREVENT

INJURY.

lNever touch uninsulated telephone wires and terminals unless the

telephone line has been disconnected at the Network Interface (NI) as

voltage potentials as high as 300 VAC may be present across the transmit

and receive pairs.

lOnly use No. 26 AWG or larger telecommunication line cord, to reduce

the risk of fire.

lNever install telephone wiring during a lightning storm.

lNever install telephone jacks in wet locations unless the jack is

specifically designed for wet locations.

lRefer to the installation section of this manual for a safe and proper

installation procedure. All wiring external to thisequipment should follow

the current provision of the National Electrical Code.

4 Compact T1 - Release 6.1

Preface

Electrostatic Discharge (ESD) Precautions

ESD can damage processors, circuit cards, and other electronic components. Always

observe the following precautions before installing a system component.

1. Do not remove a component from its protective packaging untilready to install

it.

2. Wear a wrist grounding strap and attach it to a metal part of the system unit

before handling components. If a wrist strap is not available, maintain contact

with the system unit throughout any procedure requiring ESD protection.

WARNING! INTEGRATED CIRCUITS (ICS) ARE EXTREMELY SUSCEPTIBLE TO

ELECTROSTATIC DISCHARGE. UNLESS YOU ARE AQUALIFIED SERVICE

TECHNICIAN WHO USES TOOLS AND TECHNIQUES THAT CONFORM TO ACCEPTED

INDUSTRY PRACTICES, DO NOT HANDLE ICS.

The ESD warning label appears on packages and storage bags

that contain static-sensitive products and components.

QUICK START

Quick Start

In this Guide

nUnpacking and Inspection

nInstallation Environment

nAssembly of Compact T1

nWall Mounting

nRack Mounting (Optional Feature)

nCompliant Installation

nChassis Connectors and Buttons

nInterface Connectors

nLocal and Remote Management Option

nConfiguration

nController Cards

nPower Supplies

nService Cards

2 Compact T1 - Release 6.1

Quick Start

Unpacking and Inspection

WARNING! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC

DEVICES.

1. Inspect containers for damage during shipment. Report any damage to the

freight carrier for possible insurance claims.

2. Compare packing list with office records. Report any discrepancies to the

office.

3. Open shipping containers, be careful not to damage contents.

4. Inspect contents and report any damage.

5. If equipment must be returned for any reason, carefully repack equipment in

the original shipping container with original packing materials if possible.

6. If equipment is to be installed later, replace equipment in original shipping

container and store in a safe place until ready to install.

Installation Environment

The environment in which you are installing the Compact T1 must meet the following

conditions:

lOperating temperature range: 32° to 104° F (0°to 40°C)

lStorage temperature range: -40° to 158° F (-40°to 70°C)

lCooling method is byfree air convection, requires long axis of unitto be mounted

horizontally

lMaximum operating altitude: 10,000 ft. (3,048 m)

lMaximum non-operating altitude: 40,000 ft. (12,192 m)

lRelative humidity (non-condensing) range: 0 to 95%

For operation outside the defined environment requirements, the Compact T1 must be

placed in an environmentally controlled enclosure.

Compact T1 - Release 6.1 3

Quick Start

Assembly of Compact T1

The cards should be positioned in the chassis as follows:

Note: Slots are labeled on the top and the bottom of the chassis.

lPower Supply in the POWER Slot

lT1 Controller in Slot A

lService Cards can be in any slot 1 through 6.

Note: When an Unit is mounted to the wall, cards that use the front cable

connections should be loaded from Slot 6 to 1. This will minimize card access

issues due to cable interference.

lAlways install blank faceplates in any unused slots.

Service Card Slots

123456APOWER

4 Compact T1 - Release 6.1

Quick Start

Wall Mounting

Before beginning the mounting process, verify that the area meets the following

requirements:

lA stable environment, clean and free from extremes of temperature, shock,

vibration and EMI, that meets the all installation environment requirements, see

Installation Environment on page 1-2.

The Unit is delivered with a mounting bracket attached for quick and easy wall

mounting, as shown in the illustration above.

To install the unit to the wall, attach the unit using the four screws provided, one at each

bracket foot.

NOTE: Do not mount the Unit in any other orientation as show above.

Leave at least 3.5"

above and below

the Unit for

adequate ventilation

Mounting Bracket

Leave adequate clearance

at the back for access to

connectors Leave at least 14" at

the front of the unit for

access to cards and

DIP switches

Compact T1 - Release 6.1 5

Quick Start

Rack Mounting (Optional Feature)

Rack mounting kits are available for both 19 and 23 inch racks.

To rack mount the Unit, follow the instructions below:

1. Attach bracket ears to rack mounting bracket using four #8-32 x 3/16" screws

on each side.

Bracket Ear

Left Side View

6 Compact T1 - Release 6.1

Quick Start

Rack Mounting (Optional Feature)

2. Attach heat baffle to bracket ears using two #8-32 x 5/16" screws on each side.

3. Attach rack mounting bracket ears to rack using two #12-24 x 5/8" rack

mounting screws on each side.

Heat Baffle

Left Side View

Front View

This manual suits for next models

Table of contents

Other Black Box Network Hardware manuals

Black Box

Black Box LT0009A User manual

Black Box

Black Box ACU5100A User manual

Black Box

Black Box IT Pro LNA1000A User manual

Black Box

Black Box V5.1 User manual

Black Box

Black Box TS580A-R4 User manual

Black Box

Black Box CMA005A User manual

Black Box

Black Box 16-Port Rackmount 10/100 User manual

Black Box

Black Box JPM083A User manual

Black Box

Black Box LWS100AE User manual

Black Box

Black Box ACR2004A User manual

Black Box

Black Box ME1240A-F User manual

Black Box

Black Box 5000 series User manual

Black Box

Black Box AC1059A User manual

Black Box

Black Box EncrypTight User manual

Black Box

Black Box USB Director RS-232 User manual

Black Box

Black Box JPM624A User manual

Black Box

Black Box Lineshare Master - 4 User manual

Black Box

Black Box LES1604A User manual

Black Box

Black Box AC504A User manual

Black Box

Black Box CSU/DSU User manual

Black Box

Black Box Internet Sharer FX850A User manual

Black Box

Black Box JPM083A-R3 User manual

Black Box

Black Box TL482A-R3 User manual

Black Box

Black Box LB9218A User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide